GIZMO ENGINEERING IS-AB Bedienungsanleitung
INTRINSICALLY SAFE ALARM IS-AB
1. CONNECT BATTERY
The battery pack connects with the JST connector. Only battery model
BT-IS may be used. Battery is Intrinsically Safe and may be changed
in the hazardous area. Refer to control drawing BT-IS
2. PROGRAM DESIRED MODE
•The modes available are selected using the DIP switches as follows:
3. OPERATION
•When there is a level alarm, the LED and buzzer will alternate.
The front button silences the buzzer. In the mode with switch
#2 “ON”, the LED will continue to flash until level is corrected.
If switch #1 is “ON” the buzzer will sound again after a 30
minute “snooze”.
•If the alarm is not acknowledged for 60 minutes, the alarm output
will be reduced to save battery power. After 60 minutes, all alarms
will be reduced to only 5 sec. every 30 seconds. This allows the
alarm to last for up to 600 hours (25 days) in this power-saving
mode.
4. OTHER POINTS
•Operating temperature is -40ºC to 60ºC. (-40ºF to 140ºF)
•Low battery is indicated by an alarm with which has a rapid beeping
pattern for 5 seconds every 30 seconds.
•Very low temperatures will diminish the battery life. For example if
operating at -40º, the battery will be reduced by half. See website
for more detailed information.
•If there is a second sensor connected,(on LS2) it will have a slower
beeping/flashing pattern from the first sensor. (slow vs. fast pattern)
•If there is a cable connecting to the box,the sensor is N.C,. so there
will be an alarm and relay output if the cable becomes
disconnected.
Page of 1 2
SWITCH
ON
OFF
1
30 min. buzzer snooze alarm.
No buzzer snooze alarm.
2
PB shuts off buzzer, but LED & relay stay on until
both level is corrected.
Pressing button shuts off buzzer and LED, and resets
relay, regardless of level.
3
Auto reset of LED, buzzer and relay when level is
corrected.
Manual reset: must push button after level is corrected to
reset LED and relay.
4
Relay N.O.
Relay N.C.
5
Relay output delayed 15 mins.
Relay output is immediate.
DIP SWITCHES
WITH #1 & 2 “ON”
BATTERY
BT-IS
INTRINSICALLY SAFE ALARM IS-AB
5. RELAY OUTPUT
•If the relay output is to be connected, follow parameters in “Control Drawing “IS-001” so
the remote device in the “safe” area does not introduce an unsafe voltage into the
hazardous area. Connect the remote device through an Intrinsically Safe barrier. .
Connect the output cable to the T-IS using the cable with screw-lock connector provided.
6. EXAMPLE INSTALLATION
•Install IS-AB level switch on a tank or drum by screwing the mounting thread into the tank or drum opening.
Page of 2 2
Jan 3, 2018
IS-AB ALARM
RELAY OUTPUT TO
INTRINSICALLY SAFE
BARRIER
LEVEL “PROBE”
SCREWS INTO
TANK OR DRUM
Gizmo
2257 County Road 4, Building 3, Stanley, NY 14561 585-301-0970 www.drumalarm.com
Engineering
Customer Instruction number AB-IS-002
Inhaltsverzeichnis
Andere GIZMO ENGINEERING Sicherheitssystem Handbücher
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung