Gizzmo V4 Bedienungsanleitung
Instruction Manual
Thank you for purchasing the Gizzmo V4 Boost Controller. This manual
contains operating instructions and installation procedures that are
needed for the fitment and operation of this product
www.facebook.com/gizzmoelectronics
V1.1
gizzmo
ELECTRONICS
THE V4 IS AN INFORMATIVE COMPETI TI ON GRADE BOOST CONTROLLER WI TH EVERYDAY
FUNCTI ONALI TY. TAKI NG WHAT WE KNOW FROM A OVER A DECADE OF DEVELOPMENT, AND
FROM LI STENI NG TO WHAT YOU, THE END USERS WANT,WE CONTINUALLY STRIVE TO GIVE
YOU WHAT YOU NEED.
FASTER: 32MHZ 16bit PROCESSOR. USI NG THE LATEST PROCESSOR TECHNOLOGY MEANS
THAT THI S UNI T WI LL NEVER BE WANTI NG FOR MORE PROCESSI NG POWER! THI S MEANS YOU
WI LL ALWAYS HAVE THE BEST, MOST ACCURATE BOOST CONTROL
EASE OF USE: SOMETIMES YOU JUST WANT TO KNOW WHAT THE UNIT IS DOING... NOW YOU
CAN! WE HAVE ENABLED THE DISPLAY TO SHOW NOT ONLY THE CONVENTIONAL BOOST BUT
HAVE ALSO ADDED THE ABILITY TO SEE DUTY OR RPM DUTY OFFSET
gizzmo
V4 Controller
OLED display
Gizzm o’s V4 houses a 128 by
64 OLED display so now the
menu's are less cryptic and all
of your options can be seen at
once
What's New in the V4
New Tiny Sizing
50% smaller so you can fit it
anywhere, it is easily the worlds
smallest boost controller ever.
3 buttons
Gizzm o’s V4 has added a
button to make navigation a lot
easier. this V4 is all about user
convienience
V4 CHANGES:
- OLED DISPLAY
- 50% SIZE REDUCTION
- 40% WEIGHT REDUCTION
- 3 BUTTON NAVIGATION FOR EASE OF USE
gizzmo
ELECTRONICS
V4 Specifications
Functions/ Specifications
Number of boost memories Maximum boost Processing Power
Active Over Boost
Boost Control
V4 size
Operating Voltage (v) Operating Current Reverse
Battery Protection Overcharging Protection Display
Pressure display options Wastegate Compatibility
Solenoid
6 with individual gain settings 50psi (3.5bar)
32mhz 16bitRISC 5psi to 50psi Closed with adjustable start9mm * 57mm * 26mm 11.8V
- 21V
Less than 0.5A
Yes
Yes
White graphical OLED
KPA, PSI,BAR,DC,DUTY Internal
and External
High Performance Single
9mm
26mm
57mm
26mm
57mm
26mm
57mm
1 2 3 4 5
www.facebook.com/gizzmoelectronics
For the lastest news visit...
gizzmo
ELECTRONICS
V4 Parts List
V4
Module x1
Solenoid Valve
x1
I nst ruct ion Manual
x1
5m m ‘Y’ Piece
Connector x1
Bracket and
Accessories
4 X screws
1 X stand off
2 X brackets
Cable Tie
x8
I BCR2
Harness x1
1.2m x2.8m m
Vacuum Tubing x1
3m m ‘Y’ Piece
Connector x1
Tail 5m m
x2
3m m Flat
Washer x2
3m m Nut
x2
3m m Bolt
x2
1m x5m m Nit rile
Tubing x1
12345
.
ELECTRONICS.LTD
Than k you fo r pu rch asi ng t he Gizzm o
IBC- R RPM depe nd en t Boo st Cont r o ll er
Boost Con t ro lle r. This ma nu al con ta in s
oper ating in struct ions and in stal lati on
pro cedure s that ar e neede d for t he fi ttin g
and o perat ion of t his prod uct
gizzmo
ELECTRONICS
Operating Instructions
Warning/Caution
Always connect t he wiring exact ly as described in t he inst ruct ion m anual.
Disconnect the negat ive t erm inal of t he bat t ery before proceeding wit h inst allat ion.
Do not drop or expose t his unit to excessive shock.
I nstallat ion should only be perform ed by an experienced aut om ot ive elect rician.
Keep this unit away from m oisture.
Never disassem ble, m odify, or t am per wit h t his unit .
Never operat e this unit while driving.
Securely m ount t his unit away from any area that m ay effect driving.
This unit is only designed for 12V DC t ype vehicles with a negat ive ground supply.
When in running mode the
UP button intitiates the
scramble feature. All other
modes see this used as a
shift up or increment
selection
When in running mode
pressing the DOWN button
increments the next memory
selection. Additionally,
Holding the DOWN button
enters you into the memory
setup menu. All other modes
see this used as a shift down
or decrement selection
The Enter button , in
running mode, is used to
enter the setup menus.
In all other modes it is
used to select or select &
continue.
Present
pressure
Running Display
Present memory
Selected
present Solenoid
Duty Cycle
Present
pressure
option
gizzmo
ELECTRONICS
Setup Menu Overview
To enter the menu screen below simply press the ENTER (middle) button once
Scramble: Scramble is to add additional boost (via duty) for a set
amount of time. Entering this option allows you to set how much duty
and how much time to add it for.
Display: This option allows you to select if you want your boost settings
and display in bar, psi or kpa
Overboost: This option allows you to set a boost level at which the V4
will display a warning and cut boost in the event of a over boosting
fault, this option also allows you to switch this feature off.
Input Trig: This is where you go to set up what you want to use the
external trigger input wire for, if anything. The 4 options are scramble
(as explained above), memory change which is where it increments to
the next memory setting e.g. 1>2>3... , boost cut where it'll cut to
minimum boost if this wire is switched to earth and lastely off in the
case of you not wanting to use this wire.
Anti Spike: This is to set a percentage which is proportional to the
recovery time to ramp up boost in throtle off on situations like gear
changes. This is often used to compensate for an inadequate wastegate
Hard Reset: This is for cases where you may want to return to all the
factory settings your V4 was supplied with. Some examples of these
cases might be when you are swapping the V4 to another vehicle, when
you have changed things and lost your way or when things are just
acting crazy for no aparent reason.
gizzmo
ELECTRONICS
To Change Boost Memories
To select the next memory
simply press the DOWN
button once
The MEM: display will
increment and the pressure
display will show the target
pressure for your new
memory selected
Then the running display
will return to the real time
pressure
Units of Pressure
Caution: All readings in this Manual are in BAR unless otherwise stated.
Press ENTER
Once
Press DOWN once and
then ENTER once to
select 'Display'
Use UP and DOWN to
hightlight your option
and then Enter to
save your selection
Solenoid Check I the event of a
solenoid or solenoid
loom fault, the sol flt
indication will come up
on the running screen
gizzmo
ELECTRONICS
Scramble Setup
Press ENTER once to access
menu screen Press ENTER
again to access
Scramble setup
Use the UP and DOWN buttons to adjust the
'Secs' setting inline with how many seconds
you'd like the additional boost to stay on for
and then press ENTER to continue
Use the UP and DOWN buttons to adjust the
'Perc' setting inline with how much additional
duty you'd like to add whilst on scramble and
then press ENTER to save and exit
In running mode the scramble can be
triggered by pressing the up button or
the remote trigger when the 'input
trigger' is setup as scramble. When the
scramble is triggered the 'SCR' and the
remaining seconds are displayed in the
top right hand corner of the screen as
displayed to in the image to the left
MULTI-SCRAMBLE
The V4 has Gizzmo's multi-scramble feature. With this you can re-press the UP
button or remote button whilst on scramble and the V4 will add another
additional scramble duty and replenish the seconds. That's very confusing so
here's an example. If you had your scramble duty set to 3% and secs set to 5.
Upon triggering scramble 3% duty would be added to your base duty for 5
seconds. If after 3 seconds you decided you needed more boost again, you can
repress the trigger and you would then have your base duty + 6% (3% + 3%)
and the seconds would reprenish to 5sec again. This can be done up to 2 times
in addition to the first scramble.
gizzmo
ELECTRONICS
Over Boost Setup
Press ENTER once to access
the menu screen
Press DOWN twice and
ENTER once to access
the overboost setup
NOTE: When you first enter the overboost setup it may display 'OFF'. If you
go once press above the maximum boost (in this example 3.2bar) or one
press below zero the display will read 'OFF' to indicate that overboost will be
disabled.
Use UP and DOWN to set the limit that
you would like to set at which the V4
warns you of an overboost situation and
actively switches to minimum boost. Once
you have set this press ENTER to save
and exit to the running screen
When you exceed the overboost level the display will show the
WARN logo like above and the duty will drop to zero as above
gizzmo
ELECTRONICS
Input trigger Setup
Press ENTER once to access
the menu screen
Press DOWN 3 times and
ENTER once to access the
input trigger selection
Use UP and DOWN to highlight the selection
you would like (descriptions below) and then
press ENTER and your selection will be saved
and you'll return to the running screen
SCRAMBLE: this allows the remote input to trigger scramble and multi
scramble events. As with all remote triggering options the remote wire must
switch to earth so the remote wire goes to one side of the button/switch
and the other must be connected to earth
MEMORY: this makes the remote trigger wire increment the memory
selection e.g. 1 > 2 >3... Again it switches to earth so the remote wire goes
to one side of the button/switch and the other must be connected to earth
BOOST CUT: this is used to switch to minimum boost, so mainly as a
safety feature. An example of this may be if you wired a level sensor from a
water/meth injection tank so that if it got low it would switch a eath to the
remote wire to cut boost. Please be aware that when the aux boost cut is
active (cutting boost) the running display will indicate this as below.
OFF: this is obviously to switch the aux input off so that if it earths out
nothing happens.
EXIT: this is to return to the running screen with no changes
Inhaltsverzeichnis
