GJD GJD 394 Bedienungsanleitung
GJD
TAKE CONTROL
GJD 394
D-TectX Signal Strength / Walk Tester
Engineer Instructions
The D-TectX Signal Strength / Walk Tester is a hand held battery powered
device to assist with the installation and alignment of D-TectX wireless
detectors.
The D-TectX Signal Strength / Walk Tester needs to learn the code from the
D-TectX detector being set up. The unit will then indicate when the detector
has activated and also show the strength of the .F. signal being received.
1. Battery Installation
emove battery compartment cover, install a PP3 9 Volt alkaline battery and
replace battery compartment cover.
2. Clear Code
Turn the unit on and clear any existing detector codes by pressing and
holding the LEA N button for 4 seconds until the TAMPE red LED starts to
flash, then release the button. The unit is now ready to learn a new detector
code.
3. Learn Detector Code
Plug the detector’s code transfer lead in to the LEA N socket in the end of the
D-TectX Signal Strength / Walk Tester, press and release the detector’s
Programme Button, press and release the LEA N button. After 2 seconds the
Tamper, Signal Strength 2 and 4 LEDs will flash 3 times to confirm the code
has been transferred.
If this does not show then repeat steps 2 – 3.
4. Signal Strength Testing
The detector needs to be put in to transmit test mode by pressing the
Programme Button on the detector 8 times and on the eighth press keep the
button held until the LED goes off then releas the button. The detector will
now transmit a signal every 2 seconds for approximately 8 minutes. This can
be stopped at any time by pressing the detector’s Programme Button for 4
seconds.
When the D-TectX Signal Strength / Walk Tester receives a signal from the
detector, the .F. signal strength is displayed on the 4 green LEDs.
For optimum results the D-TectX Signal Strength / Walk Tester should be held
in an upright position.
4 Beeps and 4 green LEDs indicates maximum signal strength.
3 Beeps and 3 green LEDs indicates very good signal strength.
2 Beeps and 2 green LEDs indicates good signal strength.
1 Beep and 1 green LED indicates moderate signal strength.
A weaker .F. strength is indicated by an increased time between signals
being received.
To preserve battery life on the detector it is recommended to exit the
transmit test mode after testing has been completed.
5. Walk Testing
Ensure the detector is not in transmit test mode.
Set the detector to the required detection range and align the detector head
to cover the required area then replace the detector’s cover.
When the detector has detected movement, the D-TectX Signal Strength /
Walk Tester will beep and the blue DETECTION LED will light. The LED
display will remain lit for 15 seconds, pressing the LEA N button momentarily
will clear the display.
After movement has been detected, no further detection signals will be
transmitted for 8 seconds.
To test any further detectors repeat steps 2 – 5.
After 1 minute of the D-TectX Signal Strength / Walk Tester being turned on
but with no detection or button presses then 3 consecutive beeps and blue
DETECTION LED flashes will be indicated.
GJD Manufacturing Limited, Unit 2 Birch Industrial Estate, Whittle Lane,
Heywood, Lancs., OL10 2SX, UK.
Sales 01706 363998 Fax 01706 363991 Technical 01706
363990
Inhaltsverzeichnis
Andere GJD Prüfgeräte Handbücher
Beliebte Prüfgeräte Handbücher anderer Marken
SMART
SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung
Agilent Technologies
Agilent Technologies BERT Serial Bedienungsanleitung
Agilent Technologies
Agilent Technologies N3280A Bedienungsanleitung
Vernier
Vernier Go Direct Voltage Bedienungsanleitung
Lifeloc
Lifeloc R.A.D.A.R. Bedienungsanleitung
Fluke
Fluke T5-600 Bedienungs- und Montageanleitung
PCB Piezotronics
PCB Piezotronics 8159-0112A Bedienungsanleitung
BW Technologies
BW Technologies MicroDock II Bedienungsanleitung
Sun Nuclear
Sun Nuclear 1027 Bedienungsanleitung
Biomark
Biomark HPR LITE READER Bedienungsanleitung
Hioki
Hioki 3169-20 Bedienungsanleitung
Ashcroft
Ashcroft ATE-100 Bedienungsanleitung