Glasdon ECLIPSE Bedienungsanleitung
1. Firstly establish the location your Eclipse canopy
is to be sited. To install your canopy we
recommend installing from the upper left fixing
key hole. From the ground measure approximately
2330mm upwards on the wall and mark the centre
using a pencil/scriber (diagram A).
2. Using a 12mm masonry drill bit and a hammer drill,
drill the marked hole to a depth of 110mm (diagram B).
3. Remove the washer from one of the anchors and
hammer the anchor into the drilled hole making sure it
is fully inserted (diagram C). Tighten the anchor using a
17mm socket until it is firmly secure. Once secure, then
unscrew the bolt until it is around 30mm proud of the
wall (diagram D) for the canopy to be hooked onto.
KIT CONTENTS
1 x 1.4m Canopy 4 x Cover rings
4 x Wall fixings 1 x Foam Strip
4 x 50mm Washers
4 x Cover caps
TOOLS REQUIRED
Tape measure 17mm Socket bit
Hammer battery drill Hammer
12mm Masonry drill bit Spirit Level
Socket set
ECLIPSE CANOPY INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
NOTE:
A. B.
C. D.
IMPORTANT NOTE: ENSURE ALL RELEVANT PERSONNEL READ THE POINTS LISTED WITHIN THIS LEAFLET AND
THAT A COPY IS GIVEN TO STAFF INVOLVED WITH THE INSTALLATION AND MAINTENANCE OF THIS PRODUCT.
Anchor
Anchor
Hole marking for
top left key hole
NOTE: A minimum of 2 persons are required for this installation.
Weight of the canopy: 21kg
2330
30
4. Lift the canopy up and position the top left key hole slot on the protruding
bolt. Pivot the canopy up at the opposite side ensuring the canopy is level
with the mortar lines or by using a spirit level. (diagram E).
5. Mark the remaining 3 hole
centres of your canopy using a
pencil or scriber (diagram F). The
hole positions are indicated by the
arrows above and below the fixing
slots located in the recesses in the
rear of the canopy. Carefully
remove the canopy from the bolt
and place it down on the floor.
Bolt
1
E. F.
The canopy is supplied with wall fixings suitable for solid walls of adequate strength. Although most solid
and cavity walls can typically support the canopies, they should be assessed for adequate strength and
stability by a suitably qualified person. There are a number of other anchors and resin fixings that are
probably suitable for your particular site conditions, and the appropriate fixing type should be chosen.
6. Repeat step 2 with the remaining marked holes.
7. Insert the three remaining anchors into the pre-drilled holes and tighten using a 17mm socket.
When tightened fully unscrew all four bolts so only the anchors are left inside the wall.
8. A self-adhesive foam strip is supplied to provide a seal between canopies and/or the wall. Before
using the foam strip firstly clean the recess that runs around the top edge of both sides and the rear of
the canopy, ensuring it is free from dirt/grease. For single unit installations, adhere the foam strip to the
recess at the rear of the unit, cut to the desired length and discard the excess. Where multiple units are
to be sited side by side, the foam strip should be adhered in one piece to the rear and all adjoining
sides of the canopies. NOTE: both abutting sides of the canopies should be fitted with foam strip
providing a double layer for an improved seal.
50mm washer Cover ring Bolt
Recess for
foam strip
NOTE: WHEN INSTALLING CANOPIES SIDE-
BY-SIDE, REPEAT THESE INSTRUCTIONS
FOR EACH ADDITIONAL CANOPY.
HOWEVER CARE SHOULD BE TAKEN TO
MAKE SURE THE CANOPIES ARE
POSITIONED SO THEY ARE AS CLOSE AS
POSSIBLE TO EACH OTHER AND
GENERALLY IN LINE SO THE FOAM STRIP IS
SUFFICIENTLY COMPRESSED TO SEAL.
11. Once secure, the security cover caps
should be pushed into the cover rings.
12. To complete the installation use the
remaining hole plugs and insert into the
unused fixing holes.
9. With all the anchors now inserted into the
wall, place each bolt through a cover ring and
a 50mm washer.
10. Using correct lifting procedures and
equipment, lift the canopy up onto the wall
to align the four fixing slots with the anchor
positions. Carefully re-insert the bolts
through the fixing slots so as to not disturb
the anchor or cross thread the bolt. Tighten
the bolts using a 17mm socket, adjusting
the canopy to level in the process
Outer Slot
2
Cover cap
2 x Mounting posts
8 x Cover caps
8 x Cover rings
1 x Sealing foam
2 x 17mm socket
Hammer Drill
Drill Bit
8 x 50mm washers
4 x M10 Nyloc nuts
4 x M10 x 100mm Canopy Fixings
1. Place one of the posts onto a raised surface
around 100mm from the floor. Preferably a trolley
so the unit is easy to manoeuvre when assembled.
2. Position the canopy on its side and place
the post into the recess on the back of the unit.
Place a bolt through a cover ring and then
through a 50mm washer and keep to hand.
3. Place a bolt through a cover ring and then
through a 50mm washer. Insert the assembled
bolt through the hole in the canopy until it
protrudes through the post at the back.
4. Place a 50mm washer and a cover cap
over the bolt and secure with a nyloc nut.
5. Using 17mm sockets tighten the bolt until the
canopy is securely fastened to the post.
6. Repeat steps 3,4 & 5 for the second fixing
hole until the post is securely fastened.
ECLIPSE SINGLE CANOPY POST MOUNTING ASSEMBLY INSTRUCTIONS
KIT CONTENTS TOOLS REQUIRED
3
NOTE: A minimum of 3 persons are required for this installation.
Weight of the complete assembly: 60 kg
7. Using correct lifting techniques lift the
second post and position it into the recess
on the back of the canopy.
8. Repeat steps 3, 4, 5 & 6 until the second
post is securely attached to the canopy.
9. Finally push the cover caps into the
cover ring to secure the fixings.
4
10. Using correct lifting techniques pivot the
canopy up at one end where it is to be sited.
11. Once the canopy is upright make
sure the posts are perpendicular with
the ground and adjust if necessary.
NOTE:
LIFTING AIDS SHOULD BE USED TO LIFT THE CANOPY AND POSTS WHERE POSSIBLE.
IT IS RECOMMENDED TO POSITION A SPLINT/NOGGIN BETWEEN THE TWO MOUNTING POSTS
TO KEEP THE POSTS RIGID WHEN PIVOTING THE UNIT UPWARD.
Splint Splint
FOR INSTALLATION INSTRUCTIONS FOR GROUND FIXINGS SEE PAGE 6/7
2. Position the first canopy on its side
on a raised platform and place the post
into the recess on the back of the unit.
1. Firstly apply the foam strip to the rear of each
canopy inside the shallow recess as marked above.
= Area to adhere
foam strip
3. Place a bolt through a cover ring and then through a 50mm washer and keep to hand.
4. Position the second canopy back-to-back so the post is sandwiched inside the recesses.
5. Push the bolt through the first fixing hole and the post until it protrudes through both canopies.
Insert a 50mm washer and a cover cap over the bolt and secure with a nyloc nut. Tighten the bolt
using a 17mm socket.
6. Repeat steps 3 & 4 for the second fixing
hole to secure the first post.
7. Using correct lifting techniques slide the
second post into the recess and align the holes.
8. Repeat steps 3, 4 & 5 on the remaining fixing
holes until the second post is secure.
9. Repeat steps 10 and 11 on page 4 to erect the
canopy.
ECLIPSE DOUBLE CANOPY POST MOUNTING ASSEMBLY INSTRUCTIONS
FOR INSTALLATION INSTRUCTIONS FOR GROUND FIXINGS SEE PAGE 6/7
5
NOTE: A minimum of 3 persons are required for this installation.
Weight of the complete assembly: 86 kg
Bolt
Second Post
Washer
Cover ring
Nut
2 x Mounting posts
8 x Cover caps
8 x Cover rings
1 x Sealing foam
2 x 17mm socket
Hammer Drill
Drill Bit
8 x 50mm washers
4 x M10 Nyloc nuts
4 x M10 x 190mm Canopy Fixings
KIT CONTENTS TOOLS REQUIRED
3. Insert the 60mm anchors into the pre-
drilled holes and gently hammer them down
until they are flush with ground level.
4. Re-position the posts so the fixing holes
align with the anchors. Insert the 70mm bolts
through the 20mm washers and the holes in
the base plate into the anchor sleeves.
Pre-drilled
holes
5. Using a 17mm socket loosely tighten all
four bolts on each base plate before
tightening them fully.
6. Once all bolts are fully tightened, firmly
press the tamper-proof caps onto the bolt
heads to complete the installation.
1. Firstly establish the location your Eclipse
canopy is to be sited. Mark the 8 fixing holes
in the base plate using a pencil or a scriber.
2. Remove the canopy from the marked holes
and drill them using a 16mm masonry drill bit
to a depth of around 80mm. Remove debris
and dust from inside and around the holes.
ECLIPSE CANOPY SURFACE MOUNTING KIT INSTALLATION INSTRUCTIONS
NOTE: ONCE THE CANOPY HAS BEEN PIVOTED UPRIGHT CARE SHOULD BE TAKEN TO MAKE SURE THE
POSTS ARE HORIZONTALLY LEVEL AND PERPENDICULAR TO GROUND LEVEL BEFORE MARKING.
6
20mm
washer
Base
Plate
KIT CONTENTS
8 x M10 x 70mm Bolt
8 x M10 x 60mm Anchor sleeve
8 x 20mm washer
8 x Tamper proof caps
TOOLS REQUIRED
17mm Socket bit Hammer
Hammer battery drill Spirit Level
16mm Masonry drill bit
Socket set
1. Firstly establish the location your
Eclipse canopy is to be sited. We
recommend digging a minimum hole size
of 500mm x 500mm to a depth of 550mm
as detailed above
ECLIPSE CANOPY CONCRETE IN MOUNTING KIT INSTALLATION INSTRUCTIONS
NOTE:
ONCE THE CANOPY HAS BEEN PIVOTED UPRIGHT CARE SHOULD BE TAKEN TO ENSURE THE
POSTS ARE HORIZONTALLY LEVEL AND SECURE IN THE HOLES
ASSEMBLE THE CANOPY/ CANOPIES TO THE CONCRETE IN POSTS IN THE SAME MANNER AS
INSTRUCTED ON PAGES 3, 4 & 5 OF THIS MANUAL
3. Fill the holes with around 50mm of gravel
or similar material, then position the canopy
into the holes.
2. Insert the cross bar through the hole in
the bottom of each of the posts, these will
anchor the posts when concreted.
4. Ensure the canopies are horizontally
level and the posts are perpendicular to
ground level. To ensure the canopies stay
level it is recommended that chocks or a
stabilising frame is used to keep the posts
secure within the hole prior to concreting.
Posts
5. Once secure pour concrete into the hole
until flush with ground level. Allow concrete
to harden fully to complete your installation.
1130mm Hole
Centres
7
500
500
Posts
50
NOTE:
WE RECOMMEND USING QUICK DRYING
CONCRETE (EG QC10) FOR EASE OF INSTALLATION
Stabilising frame
Should you require any further assistance please contact us on
GLASDON MANUFACTURING LIMITED
Poulton Business Park • Poulton-le-Fylde • Lancashire • FY6 8JW
Tel: 01253 891131 • Fax: 01253 891923
© Copyright GML/EclipseInstall/Dec2007
In accordance with our policy of continuous development and improvement, we reserve the right
to make changes in design and specification without notice.
Glasdon Manufacturing Limited products are manufactured under license worldwide and
various components of the models are patented and design registered.
AND ECLIPSE™ ARE TRADEMARKS OR REGISTERED TRADEMARKS OF GLASDON
GROUP OR ITS SUBSIDIARIES IN THE U.K. AND OTHER COUNTRIES
• GLASDON cannot be held responsible for claims arising from incorrect installation.
Inhaltsverzeichnis
Andere Glasdon Zelt Handbücher
