IRT
Connectors
A77
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
© 2011 Glenair, Inc. Printed in U.S.A.
CAGE Code A6854
www.glenair.com - www.glenair.it e-mail: info@glenair.it
A
Wiring Instructions - Plug Connector - Example: Size 03
Step 1
Step 2
Cut and strip the cable (See TABLE 2).
Contact Type B (mm)
1 20.0
2 20.0
3 20.0
4 21.0
5 29.0
B
TABLE 2
Crimp contacts (3) on conductors.
ITS 500
Connectors
30
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
© 2011 Glenair, Inc. Printed in Italy
CAGE Code 06324
www.glenair.com - www.glenair.it e-mail: info@glenair.it
ITS 500 Series
Reverse Bayonet Single Pole Power Connector
Assembly Instructions
17
17
18
16
19
15
14
13
12
29.50 mm
1.61”
Items Description
Receptacle Connector - Assembly Instructions
Step 1 Step 2
Step 4
Step 3
Cut and strip the cable Crimp the contact (14) on the conductor.
Insert the contact (14) crimped to the wire into the front insert (13). Install the rear insert (15) until it stops against the
front insert (13) and check that the insert is assembled correctly per the picture above.
12 - Receptacle
13 - Front Insert
14 - Male Contact
15 - Rear Insert
16 - Backshell
17 - Compression Ring
18 - Grommet
19 - Backnut
Screw the backshell (16) onto the rear external threads of the receptacle (12) and tighten. Make sure that the angled
side of the compression rings (17) are facing into the grommet (18). Then screw the backnut (19).
Electrical Test: Insulation resistance (5000 MΩ Min.). Test voltage: 3000 Vcc (1 min.).
19 17 18 16
17
Torque value = 30 N/m Torque value = 40 N/m
ITS 901
Connectors
6
GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912
© 2011 Glenair, Inc. Printed in Italy
CAGE Code 06324
www.glenair.com - www.glenair.it e-mail: info@glenair.it
Plug Connector
7 - Plug Shell
8 - Front Insert
9 - Contact
10 - Rear Insert
11 - Backend Adapter
12 - Clamp
IRT Series Components Exploded View
Plug Connector
7
8
9
11
12
10
IRT Series
Rectangular Multi Pole Power Connector
Components Exploded View
Plug with
Lever Lock System
Plug with
Screw Mating System
File:Draft1
Locazione: Errore: Nessun riferimento
3.2 0.8 max
1 / 1
Errore: Nessun riferimento
Errore: Nessun riferimento
Errore: Nessun riferimento Errore: Nessun riferimento g Errore: Nessun riferimentocm² Errore: Nessun riferimento
1:1
22/02/2222 22/02/2222 / /
CODICE
CODE
Ra (µm)
SCALA
SCALE
PART NUMBER
MATERIALE
MATERIAL
MODIFIC.
DISEGNATO
FIRMA
0.2x45°
Max.
R 0.2
Max.
GRUPPO
SERIES
ATTENZIONE:
ATTENTION:
Non sono ammessi spigoli
vivi e bave di lavorazione
.
No sharp edges or burrs allowed.
Tolleranze generali
General tolerances
ISO 2768 - fH
AREA
DESCRIZIONE
DESCRIPTION
Spigoli interni / esterni
privi di indicazione
Inner / outer edges without
specific indica tion
DRAWN
CONTROLLATO
CHECKED
APPROVATO
APPROVED
SIGNATURE
DATA
DATE
REV.
FOGLIO
SHEET
1234567
PESO
8
>
≤
≤
>
≤
>
≤
>
≤
≤
>
≤
THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF GLENAIR, INC. AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO BE DISCLOSED, REPRODUCED IN WHOLE
OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE BY ANYONE OTHER THAN GLENAIR, INC. WITHOUT WRITTEN
PERMISSION FROM GLENAIR, INC. THE INFORMATION HEREIN HAS BEEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY BE USED FOR ENGINEERING EVALUATION AND
INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM GLENAIR, INC.
IRT Series
Rectangular Multi Pole Power Connector
Wiring Instructions - Plug Connector - Example: Size 03
7
8
9
11
12
10
File:2750905701 - Contatto COMPLETO P-CE Ø14.4 - IRT4-144P-CE.dft
Locazione: Errore: Nessun riferimento
3.2 0.8 max
1 / 1
Errore: Nessun riferimento
Errore: Nessun riferimento
Errore: Nessun riferimento g 0 cm²
1:1
22/02/2222 22/02/2222 / /
CODICE
CODE
Ra (µm)
SCALA
SCALE
PART NUMBER
MATERIALE
MATERIAL
MODIFIC.
DISEGNATO
FIRMA
0.2x45°
Max.
R 0.2
Max.
GRUPPO
SERIES
ATTENZIONE:
ATTENTION:
Non sono ammessi spigoli
vivi e bave di lavorazione
.
No sharp edges or burrs allowed.
Tolleranze generali
General tolerances
ISO 2768 - fH
AREA
DESCRIZIONE
DESCRIPTION
Spigoli interni / esterni
privi di indicazione
Inner / outer edges without
specific indication
DRAWN
CONTROLLATO
CHECKED
APPROVATO
APPROVED
SIGNATURE
DATA
DATE
REV.
FOGLIO
SHEET
1234567
PESO
8
>
≤
≤
>
≤
>
≤
>
≤
≤
>
≤
THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF GLENAIR, INC. AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO BE DISCLOSED, REPRODUCED IN WHOLE
OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE BY ANYONE OTHER THAN GLENAIR, INC. WITHOUT WRITTEN
PERMISSION FROM GLENAIR, INC. THE INFORMATION HEREIN HAS BEEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY BE USED FOR ENGINEERING EVALUATION AND
INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM GLENAIR, INC.
File:2750905701 - Contatto COMPLETO P-CE Ø14.4 - IRT4-144P-CE.dft
Locazione: Errore: Nessun riferimento
3.2 0.8 max
1 / 1
Errore: Nessun riferimento
Errore: Nessun riferimento
Errore: Nessun riferimento g 0 cm²
1:1
22/02/2222 22/02/2222 / /
CODICE
CODE
Ra (µm)
SCALA
SCALE
PART NUMBER
MATERIALE
MATERIAL
MODIFIC.
DISEGNATO
FIRMA
0.2x45°
Max.
R 0.2
Max.
GRUPPO
SERIES
ATTENZIONE:
ATTENTION:
Non sono ammessi spigoli
vivi e bave di lavorazione
.
No sharp edges or burrs allowed.
Tolleranze generali
General tolerances
ISO 2768 - fH
AREA
DESCRIZIONE
DESCRIPTION
Spigoli interni / esterni
privi di indicazione
Inner / outer edges without
specific indication
DRAWN
CONTROLLATO
CHECKED
APPROVATO
APPROVED
SIGNATURE
DATA
DATE
REV.
FOGLIO
SHEET
1234567
PESO
8
>
≤
≤
>
≤
>
≤
>
≤
≤
>
≤
THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF GLENAIR, INC. AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO BE DISCLOSED, REPRODUCED IN WHOLE
OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE BY ANYONE OTHER THAN GLENAIR, INC. WITHOUT WRITTEN
PERMISSION FROM GLENAIR, INC. THE INFORMATION HEREIN HAS BEEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY BE USED FOR ENGINEERING EVALUATION AND
INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM GLENAIR, INC.
File:2750905701 - Contatto COMPLETO P-CE Ø14.4 - IRT4-144P-CE.dft
Locazione: Errore: Nessun riferimento
3.2 0.8 max
1 / 1
Errore: Nessun riferimento
Errore: Nessun riferimento
Errore: Nessun riferimento g 0 cm²
1:1
22/02/2222 22/02/2222 / /
CODICE
CODE
Ra (µm)
SCALA
SCALE
PART NUMBER
MATERIALE
MATERIAL
MODIFIC.
DISEGNATO
FIRMA
0.2x45°
Max.
R 0.2
Max.
GRUPPO
SERIES
ATTENZIONE:
ATTENTION:
Non sono ammessi spigoli
vivi e bave di lavorazione
.
No sharp edges or burrs allowed.
Tolleranze generali
General tolerances
ISO 2768 - fH
AREA
DESCRIZIONE
DESCRIPTION
Spigoli interni / esterni
privi di indicazione
Inner / outer edges without
specific indication
DRAWN
CONTROLLATO
CHECKED
APPROVATO
APPROVED
SIGNATURE
DATA
DATE
REV.
FOGLIO
SHEET
1234567
PESO
8
>
≤
≤
>
≤
>
≤
>
≤
≤
>
≤
THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF GLENAIR, INC. AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO BE DISCLOSED, REPRODUCED IN WHOLE
OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE BY ANYONE OTHER THAN GLENAIR, INC. WITHOUT WRITTEN
PERMISSION FROM GLENAIR, INC. THE INFORMATION HEREIN HAS BEEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY BE USED FOR ENGINEERING EVALUATION AND
INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM GLENAIR, INC.
File:2750905701 - Contatto COMPLETO P-CE Ø14.4 - IRT4-144P-CE.dft
Locazione: Errore: Nessun riferimento
3.2 0.8 max
1 / 1
Errore: Nessun riferimento
Errore: Nessun riferimento
Errore: Nessun riferimento g 0 cm²
1:1
22/02/2222 22/02/2222 / /
CODICE
CODE
Ra (µm)
SCALA
SCALE
PART NUMBER
MATERIALE
MATERIAL
MODIFIC.
DISEGNATO
FIRMA
0.2x45°
Max.
R 0.2
Max.
GRUPPO
SERIES
ATTENZIONE:
ATTENTION:
Non sono ammessi spigoli
vivi e bave di lavorazione
.
No sharp edges or burrs allowed.
Tolleranze generali
General tolerances
ISO 2768 - fH
AREA
DESCRIZIONE
DESCRIPTION
Spigoli interni / esterni
privi di indicazione
Inner / outer edges without
specific indication
DRAWN
CONTROLLATO
CHECKED
APPROVATO
APPROVED
SIGNATURE
DATA
DATE
REV.
FOGLIO
SHEET
1234567
PESO
8
>
≤
≤
>
≤
>
≤
>
≤
≤
>
≤
THIS COPYRIGHTED DOCUMENT IS THE PROPERTY OF GLENAIR, INC. AND IS FURNISHED ON THE CONDITION THAT IT IS NOT TO BE DISCLOSED, REPRODUCED IN WHOLE
OR IN PART, OR USED TO SOLICIT QUOTATIONS FROM COMPETITIVE SOURCES, OR USED FOR MANUFACTURE BY ANYONE OTHER THAN GLENAIR, INC. WITHOUT WRITTEN
PERMISSION FROM GLENAIR, INC. THE INFORMATION HEREIN HAS BEEN DEVELOPED AT GLENAIR'S EXPENSE AND MAY BE USED FOR ENGINEERING EVALUATION AND
INCORPORATION INTO TECHNICAL SPECIFICATIONS AND OTHER DOCUMENTS WHICH SPECIFY PROCUREMENT OF PRODUCTS FROM GLENAIR, INC.
Valid for all sizes
Valid for all kinds
of backend
