Global Skyware 9013 Bedienungsanleitung

Global Skyware 1315 Outlet Center Drive Smitheld, NC 27577

90CM KA-BAND

TYPE 9013 ANTENNA SYSTEM

with Factory Assembled Az/El Mount

A ORIGINAL RELEASE MAR 2017 R. Thompson

REV. DESCRIPTION DATE APPROVED

MARCH 2017

Revision A

ASSEMBLY MANUAL

8001121-01

Global Skyware 90CM KA BAND

ASSEMBLY MANUAL

90CM KA-BAND ANTENNA SYSTEM

TABLE OF CONTENTS

SECTION TITLE PAGE

I GENERAL INFORMATION

1.0 PARTS LIST 1

1.1 TOOLS REQUIRED 2

II ASSEMBLY INSTRUCTIONS

2.0 ASSEMBLY AND INSTALLATION 3-4

2.1 ANTENNA ALIGNMENT PROCEDURE 5

2.2 GROUNDING PROCEDURE 6

III CHARTS

3.0 POLARIZATION CHART 7

3.1 ELEVATION CHART 8

3.2 AZIMUTH CHART 9

IV APPENDIX A

4.0 SITE SELECTION 10

4.1 WARNINGS 10

4.2 PERIODIC INSPECTION AND MAINTENANCE 11

4.3 WARRANTY 12

5/1

5/2

5/5

5/4

62-9013568

ITEM DESCRIPTION QT Y.

190cm Type 9013 KA Reector 1

2 Feed Arm with Bracket 1

3 90cm KA Band Az/El 1

4 Back Bracket 1

5 90cm Hardware Kits (Contents Below) 1

5/1 5/16”-18 UNC x 3/4” Round Head Square Neck Bolt 10

5/2 5/16”-18 UNC Hex Flange Nut 10

5/3 5/16”-18 UNC x 2 1/4” Hex Bolt 2

5/4 5/16”-18 UNC Hex Nylock Nut 3

5/5 5/16”-18 UNC Narrow Flat Washer 5

5/6 Boom Arm Plate 1

5/7 5/16”-18 UNC Carriage Bolt 1

1.0 PARTS LIST

5/3

5/1

5/7

5/6

1.1 TOOLS REQUIRED

Compass Clinometer Torque Wrench

ADDITIONAL INSTALLATION MATERIALS (Not Included with Antenna)

Installaon Mount (Ground Pole, King Post, Wall Mount or Roof Mount)

Grounding Rod, Clamp & Grounding Block - As required by Naonal Electric Code or local codes.

Ground Wire - #10 solid copper or #8 aluminum as required by Naonal Electric Code or local codes (length as required).

RG-6 Coaxial Cables from antenna to indoor units.

Concrete: See “Ground Pole” secon for quanty

M10 or #3 Rebar: See “Ground Pole” secon for quanty. Deformed steel per ASTM A615, Grade 40 or 60.

9” Magnec Level #1 or #2 Phillips 3/8” Drive

Screwdriver Ratchet Wrench

5/16” Nut Driver 1/4” Socket (3/8” Drive) 1/4” Combinaon Wrench

5/16” Deep Socket (3/8” Drive) 5/16” Combinaon Wrench

Step 0 - Site Selecon and Ground Pole Installaon

A site with a clear, unobstructed view is preferred. Also consider obstrucon that may occur in the

future such as the growth of trees.

>See secon 4.0 for more details.

2.0 ASSEMBLY AND INSTALLATION

5/2

Step 1 - Aach AzEl to Back Bracket

1. From inside the Back Bracket, align the ve hole

paern on the Az/El.

2. Feed the (5) 5/16 x 3/4” RHSN bolts (Item 5/1)

from the back bracket to the Az/El.

3. Secure with (5) 5/16 hex ange nuts (Item 5/2).

Torque to a maximum of 15 /lbs.

5/1

Step 2 - Install Antenna on Mounng Pipe

1. Before aaching the Antenna system to the

mounng pipe use a magnec level to verify the

horizontal and vercal level of the pipe.

2. Being aware of health & safety at all mes, Carry

the Antenna to the pipe.

3. Slide the tube canister of the Az/El Assembly

(Item 3) over the top of the pipe and lower into

place.

4. Secure in place at this stage by hand ghtening

the 5/16” ange nuts on the canister assembly.

Step 4 - Aach the Feed Arm to the Back

Bracket

1. Insert one 5/16”-18 x 2-1/4” carriage bolt (Item

5/7) into the boom arm from the top.

2. Place the boom arm to align with the back

bracket holes and secure with two 5/16”-18

x 2-1/4 inch hex bolts (Item 5/3), 5/16-18 at

washer (Item 5/5) and 5/16-18 hex nylock nuts

(Item 5/4).

3. Finally, as shown here aach the boom arm

plate (Item 5/6) to the boom arm and back

bracket by aligning the 5/16-18 carriage bolt (Item

5/7)into the hole in the plate and secure using

at washer (Item 5/5) and 5/16-18 hex nylock nut

(Item 5/4).

2.0 ASSEMBLY AND INSTALLATION

Step 3 - Aach Reector to Back Bracket

1. Insert ve 5/16-inch x 3/4-inch carriage bolts

(Item 5/1) into the holes in the reector and through

the corresponding holes in the reector back bracket.

2. From the rear of the reector back bracket, secure

the ve carriage bolts (Item 5/1) with four 5/16-inch

hex ange nuts (Item 5/2).

3. Tighten the ve 5/16-inch hex ange nuts (Item

5/2) to 8 -lb of torque.

Note : Ensure that the carriage bolts (Item 5/1) are properly and rmly

seated before ghtening the nuts.

5/55/4

5/3

5/5

5/4

5/5

5/6

5/1

5/2

5/7

Elevaon Fine Adjustment

1. Make nal adjustments to the elevaon by making slight

adjustments to the 5/16” ange nuts on the threaded

elevaon rod.

2. Adjust the nuts along the length to increase or decrease

the seng to achieve the desired elevaon.

3. Aer the correct elevaon has been established, ghten

the two(2) 5/16” ange nuts located in the arched slots

on the side of the Mount Assembly to 20 Nm (15  – lb)

and ghten the two(2) 5/16” ange nuts on the threaded

elevaon rod using a 1/2" wrench.

Elevaon Coarse Adjustment

1. Slightly loosen the two(2) 5/16” ange nuts located in the

arched slots in the sides of the Mount assembly and the two(2)

5/16” ange nuts on the threaded adjustment rod at the back of

the assembly.

2. Adjust the posion of the 5/16” ange nuts on the threaded

adjustment rod along the length of the rod to adjust the elevaon

angle, moving the nuts up & down to nd the correct posion.

Azimuth Coarse Adjustment

1. Using a compass, set the Antenna in the correct pre-determined

direcon.

2. Secure this posion by fully ghtening the three(3) 5/16”

locking nuts to the canister using a 1/2" wrench.

2.1 ANTENNA ALIGNMENT PROCEDURE

Azimuth Fine Adjustment

1. Slightly loosen the three(3) 5/16” locking nuts mounted to

the underside of the mount assembly.

2. Adjust the azimuth by turning the adjustment screw

clockwise or counter-clockwise unl the desired angle is

achieved.

3. Aer vericaon with a compass and meter, re-lock the

5/16” nuts to 20 Nm (15  – lb) using a 1/2” wrench.

5/16” Flange

Nuts

5/16” Locking

Nuts

5/16” Locking Nuts

5/16” Flange Nuts

Azimuth

Adjustment

Screw

INSTALLATION POLE MOUNT

Note: Grounding wire and hardware are not supplied for pole

mount, trimast wall mount or non penetrang roof mount. Installa-

on mount and associated hardware are not supplied.

A grounding screw is provided on the azel as indicated.

Ground Wire

with Ring Clip

1/4”

Drilling

Screw

Ground

Lug

Tooth

Washer

TRIMAST WALL MOUNT

Tooth

Washer

Ground Wire

with Ring Clip

Ground

Lug

Lock

Nut

M6 x 16 mm

Hex Head

Screw

TO GROUNDING

ROD

Non Penetrang

Roof Mount

M6 x 16 mm

Self Tapping

Screw

Ground

Lug

Ground Wire

with Ring Clip

Tooth Washer

Ground Wire

Secure

Clamp

Grounding Rod

TO GROUNDING

ROD

Ground Wire

(NEC Secon

810-20)

Ground Block

(NEC Secon

810-20)

Coaxial Cables (To IDU)

Note: Ground wire, secure clamp, grounding

rod, coaxial cables and ground block are not

supplied.

IMPORTANT: All antenna sytems must be properly grounded. Refer to NEC (Naon-

al Electric Code) Arcle 810, 820 and local building codes for specic requirements.

Typical grounding methods are shown as examples. Tighten all hardware securely

to assure good connuity.

AZEL GROUNDING

SCREW

2.2 GROUNDING PROCEDURE

Polarizaon Chart Sign Values (+ or -) Northern Hemisphere Southern Hemisphere

Antenna Site West of Satellite Longitude -+

Antenna Site East of Satellite Longitude +-

POLARIZATION IN DEGREES

EARTH STATION LATITUDE IN DEGREES NORTH OR SOUTH OF EQUATOR

FEED ROTATION

(Facing Antenna)

For + Polarizaon Rotate Counter Clockwise

For - Polarizaon Rotate Clockwise

Antenna

Feed

3.0 POLARIZATION CHART

ELEVATION IN DEGREES

Use of Elevaon Chart

(1) Determine = the dierence between your site longitude and the satellite longitude.

(2) Find your latude on horizontal axis.

(3) Follow your latude up unl you intersect the curve for your .

(4) Read Elevaon value on vercal axis.

EARTH STATION LATITUDE IN DEGREES NORTH OR SOUTH OF EQUATOR

3.1 ELEVATION CHART

Inhaltsverzeichnis

Andere Global Skyware Antenne Handbücher

Global Skyware

Global Skyware 122H Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung