GLP 7687 Bedienungsanleitung

User Manual

Luminaire software version 118

Hardware version 10074xxxxx or higher

GLP® impression® FR1 TM (Trackmount) User Manual Revision C

This manual covers firmware version 118 and hardware version 10074xxxxx or higher

The marks ‘GLP’ and ‘German Light Products’ are trademarks registered as the property of

German Light Products GmbH in Germany, in the United States of America and in other

countries.

The information contained in this document is subject to change without notice. German Light

Products GmbH and all affiliated companies disclaim liability for any injury, damage, direct or

indirect loss, consequential or economic loss or any other loss occasioned by the use of,

inability to use or reliance on the information contained in this document.

Manufacturer head office:

German Light Products GmbH (GLP), Industriestrasse 2, 76307 Karlsbad, Germany

Tel (Germany): +49 7248 92719 - 0

Service & Support EMEA:

GLP, Industriestrasse 2, 76307 Karlsbad, Germany

Tel. (Germany): +49 7248 9271955

Email: [email protected]

www.glp.de

Service & Support USA:

GLP USA, 1145 Arroyo St., Ste. A, 91340 San Fernando, California

Tel (USA): +1 818 767 8899

Support (US): [email protected]

www.germanlightproducts.com

Contents

Safety.......................................................................................... 4

Avoiding damage..................................................................... 9

Product overview .................................................................... 10

Product features...................................................................... 11

Preparing for use...................................................................... 15

Control menus and LCD display ............................................ 21

Control menu layout ............................................................... 22

DMX channel layout ............................................................... 27

Service and maintenance ..................................................... 30

Technical specifications ......................................................... 33

Dimensions ............................................................................... 35

www.glp.de

4 impression® FR1 TM User Manual

Safety

Key to symbols

The following symbols are used in this manual:

General safety information

Read this section carefully before installing or using the impression® FR1 TM

(Trackmount) luminaire. If you have any doubts or questions about how to use the

luminaire safely, contact your GLP® supplier for assistance. Your GLP supplier will be

happy to help.

The impression FR1 TM and this user manual are intended for use by experienced

professionals with the knowledge and skills to set up, operate, and maintain high-

powered, remotely controlled lighting equipment safely and efficiently. These

operations require expertise that may not be provided in this manual.

• Respect all warnings and directions given in this user manual and on the luminaire.

Read this manual and familiarize yourself with the safety precautions it contains

before installing or using the luminaire. The manufacturer will take no responsibility for

damages or harm resulting from disregard for the information in this manual.

• Check the GLP website at www.glp.de and make sure that you have the latest

version of this user manual. Check also that the software version indicated on page 2

of the user manual matches the version installed in the luminaire. You can download

the correct version of this user manual if necessary.

• Make the user manual available to all installers and operators and save the manual

for future reference.

Warning! Safety hazard.

Risk of severe injury or

death.

Warning! Hazardous voltage.

Risk of lethal or severe

electric shock.

Warning! See user

manual for important

safety information.

Warning! Fire hazard.

Warning! Risk of eye

injury.

German Light Products®

impression® FR1 TM User Manual 5

• If you have questions about the safe installation, operation or maintenance of the

impression FR1 TM, please contact an authorized GLP distributor (see list of distributors

at www.glp.de).

• Use the luminaire only as directed in this user manual. Observe all markings in this user

manual and on the luminaire.

• Refer any service operation not described in this manual and refer all repairs to a

technician authorized by GLP.

• The light source in this luminaire must not be changed by the end user.

• Read and follow the user documentation for all additional equipment.

Electrical safety

• Do not allow the luminaire to come into contact with water or moisture.

• Install the luminaire on EUTRAC 3 lighting track that is correctly and safely installed in

accordance with the lighting track’s user documentation and with local building and

electrical codes. The lighting track must be electrically connected to ground (earth)

and the installation must have both overload and ground fault (earth fault)

protection. The track must be in perfect condition and be rated for the electrical

requirements of all devices mounted on it. For more information, see the lighting track

manufacturer’s documentation.

• The lighting track must be connected to AC mains power at 100-240 V, 50/60 Hz. Do

not mount the luminaire on lighting track that is supplied with power from a dimmer or

presence detector.

• Shut down and lock out AC mains power to the lighting track before carrying out any

installation or maintenance work.

• Shut down power to the lighting track when the luminaire is not in use.

• Shut down power to the lighting track immediately if the track, luminaire or any seal,

cover, cable, or other component is damaged, defective, deformed, wet or showing

signs of overheating. Do not reapply power until the item has been repaired and

made safe by a qualified technician authorized by GLP.

• If a fuse blows, replace it with one of the original type and rating only. If new fuses

blow, disconnect the luminaire from power and send it to a technician authorized by

GLP for repair.

www.glp.de

6 impression® FR1 TM User Manual

Fire safety and protection from burns

• Do not operate the luminaire if the ambient temperature (Ta) exceeds 45° C (115° F).

• The surface of the luminaire’s casing can reach up to 55° C (131° F) during operation.

Avoid contact by persons and materials. Do not install the luminaire in a location

where there is a risk of accidental contact. Allow the luminaire to cool for at least 10

minutes before handling

• Keep the luminaire well away from flammable materials.

• Keep all combustible materials (e.g. fabric, wood, paper) at least 100 mm (4 in.)

away from the luminaire.

• Ensure that there is free and unobstructed airflow around the luminaire. Provide a

minimum clearance of 100 mm (4 in.) around fans and air vents.

• Do not illuminate surfaces within 500 mm (19.7 in.) of the luminaire.

• Do not install a fuse that has a higher rating than the one originally installed in the

luminaire. Do not bypass fuses.

• Do not stick filters, masks or other materials onto optical components.

• The luminaire’s optical components can focus the sun’s rays, creating a risk of fire and

damage. Do not expose the front of the luminaire to sunlight or any other intense light

source, even from an angle.

Eye safety

• The impression FR1 TM is classified as a Risk Group 2 luminaire according to EN 62471.

Possibly hazardous radiation emitted.

• Do not stare into the light output from the luminaire. May be harmful to the eyes.

• Do not look at the luminaire’s light output with optical instruments or any device that

may concentrate the light output.

• Make sure that persons working on or near the luminaire are not looking directly into

the light output when the luminaire lights up suddenly. This can happen when power

is applied, when the luminaire receives a DMX signal, or when certain control menu

items are selected.

• Provide well-lit conditions to reduce the pupil diameter of anyone working on or near

the luminaire.

German Light Products®

impression® FR1 TM User Manual 7

Strobe safety

• Flashing light, particularly at 5 - 30 Hz, may cause seizures in persons with

photosensitive epilepsy. Do not use strobe effects for extended periods.

• Comply with local regulations on the use of strobe lighting and notify the public in

advance with highly visible warning signs when strobe effects are used.

• If a seizure occurs, stop using strobe effects. Seek professional medical help. Note the

time that the seizure starts and finishes. Call emergency medical help urgently if the

seizure lasts more than five minutes, if it is the person’s first seizure, or if the person is

injured. While waiting for help to arrive, consider the following general advice for

caring for a person who is having a seizure: Protect the affected person from injuring

themselves on hard or sharp objects. If necessary, move the person to a safe place.

Lay them on their side with their head supported to prevent it from hitting the floor.

Loosen any tight clothing around their neck. Do not use force to hold the person or

restrict their movements. Do not put anything in their mouth, including your fingers.

Installation safety and protection from personal injury

• Installation must be performed by qualified personnel only and carried out in

accordance with applicable regulations such as DIN VDE 0711-217.

• Restrict access below the work area and work from a stable platform whenever

installing, servicing or moving the luminaire.

• Mount the luminaire only on EUTRAC 3 lighting track that is correctly and safely

installed and rated for the weight of all the devices that will be installed on it.

• When installing a luminaire, support its weight until you have closed both of the two

mechanical fasteners at each side of the luminaire to lock the fasteners into the

lighting track. Do not allow the luminaire to hang from only one mechanical fastener.

• Allow a minimum center-to-center distance of 1000 mm / 40 in. between luminaires

on the lighting track. Do not install luminaires at less than this distance from each other

or you may overload the track and cause a safety hazard.

• Secure the luminaire against falling if the primary trackmount adapter fails by

equipping it with a safety cable as directed in this manual. The safety cable must be

approved for the weight of the luminaire and fastened to a secure anchoring point in

a fixed structure. If no fixed structure is available, secure the luminaire using the safety

cable and retaining collar supplied with the luminaire (or identical replacement items

supplied by GLP) as directed in this manual.

www.glp.de

8 impression® FR1 TM User Manual

• Before applying power to the luminaire, ensure that all fasteners are correctly closed,

that the luminaire is secure, and that the moving head can move through its full

range without risk of collision.

• Do not operate the luminaire with missing or damaged covers, shields or any optical

component.

• If the luminaire becomes damaged, stop using it immediately and remove it from the

installation. Do not attempt to use a luminaire that is obviously damaged.

• Do not modify the luminaire in any way not described in this user manual.

• Install genuine GLP parts only.

German Light Products®

impression® FR1 TM User Manual 9

Avoiding damage

Do not point the front of the luminaire towards the sun or other strong light sources. The

front lens focuses and concentrates light just like a magnifying glass. Strong light can

cause internal damage to the luminaire, melting components or starting an internal fire

within seconds.

Figure 1. Avoiding damage from light sources

Damage can occur whether the luminaire is powered on or off. See Figure 1.Damage

can also occur if the light hits the front of the luminaire at an angle: the luminaire does

not need to be pointing directly at the sun or other light source.

To avoid problems from strong light sources:

• Do not expose the front of a luminaire to sunlight or any other strong light source.

• For outdoor applications during daylight, make sure that the front face of any

luminaire is shielded or points away from the sun, even when not in use.

• Avoid pointing other high-powered beam lights directly at the luminaire.

Do not pick up or carry the luminaire by the front lens bezel. The LCD display is also

fragile. Picking up or supporting the luminaire in these spots could result in damage

that is not covered by the product warranty.

Use only original spare parts. Any structural modification of the system will void the

product warranty.

Inspect the luminaire regularly and clean it if necessary. Clean the luminaire only as

directed in this manual. Oils, solvents, and other chemicals commonly used for

cleaning can damage the lens coatings and surfaces.

Do not drop the luminaire or expose it to mechanical stress.

Do not expose the luminaire to heat (from other lighting luminaires for example).

Transportation and storage

Transport the impression FR1 TM either in a flightcase or in its original packaging to

protect the luminaire from damage caused by shocks during transportation.

Store the luminaire in a dry location when not in use.

www.glp.de

10 impression® FR1 TM User Manual

Product overview

Figure 2: Product overview

A – Front lens assembly

B – Control panel with backlit LCD display

C – Wireless control antenna

D – Combined mechanical fastener and

power phase selection handscrew

E – Trackmount adapter

F – Cooling vent

G – Wireless control linking button

H – Mechanical fastener lever locking screw

I – Fuseholder

J – Safety cable attachment point

K – Mechanical fastener lever

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GLP DJ-Equipment Handbücher

GLP

GLP JDC1 Bedienungsanleitung

GLP

GLP KNV Series Bedienungsanleitung

GLP

GLP IMPRESSION X4L Bedienungsanleitung

GLP

GLP YPOC CMY 700 Bedienungsanleitung

GLP

GLP Impression E350 Bedienungsanleitung

GLP

GLP YPOC 575 Bedienungsanleitung

GLP

GLP Fusion EXO Beam 10 Bedienungsanleitung

GLP

GLP impression x4 bar Kurzanleitung

GLP

GLP Impression Series Bedienungsanleitung

GLP

GLP Startec-1200 Bedienungsanleitung

GLP

GLP Impression XL Bedienungsanleitung

GLP

GLP JDC Line 500 Bedienungsanleitung

GLP

GLP X4 ATOM series Bedienungsanleitung

GLP

GLP Junior Scan 3 Bedienungsanleitung

GLP

GLP Highlander Wash Bedienungsanleitung

GLP

GLP POCKET SCAN Bedienungsanleitung

GLP

GLP impression FR1 TM Bedienungsanleitung

GLP

GLP VOLKSLICHT R-G-B Bedienungsanleitung

GLP

GLP inmpression E 350 Bedienungsanleitung

GLP

GLP GT-1 Bedienungsanleitung

GLP

GLP YPOC 575 COLOR Bedienungsanleitung

GLP

GLP YPOC 250 Color Bedienungsanleitung

GLP

GLP impression FRIO BAR Bedienungsanleitung

GLP

GLP impression X4 Bar 20 Bedienungsanleitung

Beliebte DJ-Equipment Handbücher anderer Marken

ALPHA LITE

ALPHA LITE ALPHA 1500 Betriebsanleitung

Chauvet

Chauvet OVATION E-930VW Bedienungsanleitung

Zumtobel

Zumtobel APHRODITE Home Bedienungsanleitung

Snow Masters

Snow Masters Zig Oscillator Bedienungsanleitung

EuroLite

EuroLite 50530554 Bedienungsanleitung

Beamz

Beamz BUV243 Bedienungsanleitung

thomann

thomann Stairville DJ Lase 40-G MK-III Bedienungsanleitung

Eagletone

Eagletone 6 Eyes Flower Bedienungsanleitung

EuroLite

EuroLite FLD-1508 Bedienungsanleitung

Technical Pro

Technical Pro LG8xSEA Bedienungsanleitung

JB Systems

JB Systems Lounge Laser DMX Bedienungsanleitung

Lightmaxx

Lightmaxx Vega Halo 90 Bedienungsanleitung

Elation

Elation FUZE WASH Z350 Bedienungsanleitung

Maverick

Maverick MK3 WASH Bedienungsanleitung

Infinity

Infinity TF-260C7 Fresnel Bedienungsanleitung

Chauvet

Chauvet EVE E-50Z Bedienungsanleitung

Eliminator Lighting

Eliminator Lighting E 138 Bedienungsanleitung

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Bedienungsanleitung