GMC ETV Bedienungsanleitung

ETV trouble shooting guide

Typical faults:

1- Bad cutting / bending

2- Length jumping

3- Double cutting

1 Knife adjusting:

I. Removing the knife brake-bar.

When removing the brake-bar, check the green rubber, and make sure it is not worn down.

II. Removing the upper knife.

NOTE: The knife is sharp and should be handled with care!

The knife is held in place by four nuts and springs, and two plates. By removing these the top knife

will be loose, take care the knife does not fall off the bolts. This can cause injury or damage to the

knife.

When the upper knife is flipped down you can gain access to the bottom knife, and adjust it from

here. If you need to remove the knife completely, this can be done by loosening the two bolt in

each side of the knife.

III. Adjusting bottom knife.

The knife is held in place by three bolts, to dismount the knife, you will need to loosen these. Note

that one side of the knife have been grind down 0,6mm. This side must always face towards the

machine.

If the knife does not cut clean throughout the length, it can be shimmed up to correct this issue.

-Mark the knife with a pen where the cut is bad.

-Loosen the mounting bolts on the bottom knife.

-Insert a strip of silicone pack paper (50 Microns) behind the knife where you marked it.

NOTE: Make sure not to cover the air holes with the paper!

-Tighten the bolts on the knife.

NOTE: Never use more than 5 layers of paper!

The bottom knife can also be adjusted via the threaded holes located by the mounting bolts,

however this should only be done after consulting with the manufacturer, if done incorrectly it can

damage the knife.

2 Adjusting the brake:

I. Start with removing the brake-bar

Check all parts for marks or other damage. Check straightness of the bar, the rubber and the brass

bracket.

II. Adjusting the magnet of brake.

Adjust the magnets and place the brake-bar back. Distance between rubber strip and brake-bar

should now allow two to three layers of material to pass through, there should be friction when

trying to pass through 4 layers. The adjustment is checked by starting the sheeter and running

length mode, with approx. two cuttings per second and with no web. Insert a piece of paper into

the brake and check that the paper cannot move when the brake is pressing against the paper.

Move the paper laterally through the whole width of the brake.

3- Adjusting the cut

I. Adjusting the Warner clutch.

First make sure the Warner clutch is set to is start position, where the pal is placed on the

counterpart.

NOTE: Keep the clutch free of grease and oil, as this can be a cause of malfunction.

II. Adjust the camshaft.

Adjust the camshaft so the knife is placed in top position. This is done by loosening the two bolts as

shown on the picture. When knife is in top position the bolts are tightened again.

III. Adjust the outer ring.

Adjust the outer ring so it activates the sensor, the sensor will light up when activated.

Inhaltsverzeichnis

Andere GMC Cutter Handbücher

GMC

GMC GMC1250 Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung

RODCRAFT

RODCRAFT RC7170 Bedienungsanleitung