GME RM600D Technisches Handbuch

RM600D INSTRUCTION MANUAL PAGE 1

INFORMATION LEAFLET

REMOTE UNIT

TO SUIT GX600D

RM600D

PAGE 2 INSTRUCTION MANUAL RM600D

REAR PANEL CONNECTIONs

PLEAsE NOTE

The GME RM600D is a remote unit to suit the

GX600D. Please refer to your GX600D manual for

operating instructions and operator qualiﬁcations.

INTRODUCTION

Congratulations on your purchase of the GME RM600D.

With its compact size and waterproof design it can easily be

installed into almost any panel mounting location in your ﬂy

bridge or cabin.

The RM600D is totally designed and manufactured at our

factory in Gladesville, Australia. Precision robots and the

very latest manufacturing techniques ensure a consistent

high quality is maintained, resulting in a communications

system of extreme reliability and performance.

ACCEssORIEs sUPPLIED

The RM600D is supplied with the following.

• Mounting bracket and Gimball knobs

• DC battery lead

• Remote interconnecting cable

• MC504 microphone

• Mounting hardware

• Information leaﬂet

Please immediately contact your point of purchase if any

of these components are missing.

RM600D REMOTE UNIT

The RM600D remote unit provides a remote head

connection to allow operation of the GX600D from

a ﬂybridge or second station on your vessel.

The RM600D conveniently plugs into the GX600D using

an interconnecting cable and no additional interface

wiring is required.

The RM600D is supplied with a DC lead for connection

to a 12 Volt power source and 5 metres of terminated

interconnecting cable. Additional terminated cables are

available in 5 and 10 metre lengths.

When connected, the RM600D can duplicate all functions

of the GX600D. In addition it includes an Intercom feature

that allows internal communications between the GX600D

and the RM600D.

The RM600D is supplied with a standard PTT microphone

which is interchangeable with the alphanumeric

microphone supplied with the GX600D: Because of the

additional functions accessible from the alphanumeric

microphone, master control is given to whichever device

has the alphanumeric microphone connected: However

the main unit GX600D always has priority. If the GX600D

is switched off the system will not operate and no back

lighting will show on the RM600D LCD display. Before

changing the microphones, both units should be

switched off.

Note: Only one alphanumeric microphone should be

connected to any GX600D/RM600D combination.

REsTRICTIONs OF UsE

European Telecommunications Standard Institute (ESTI) has

stipulated the speciﬁc requirements (EN 301 025-1/2/3) for

marine radio with class D DSC feature. This equipment is not

for use on SOLAS vessels or vessels on inland waterways.This

radio is intended for use in European countries: DK, FI, FR,

DE, GR, IE, IT, MT, NL, PT, ES, SE, GB, IS, NO AND TR.

Mounting Bracket

DC Power Cable Extension Speaker Socket

Gimbal Knob

Inter Connecting

Cable to main unit

0168 !

RM600D INSTRUCTION MANUAL PAGE 3

sPECIFICATIONs

ELECTRICAL

Supply Voltage: 12 Volt Nominal

10.5-15.6 Volt Max. range

Negative earth

Current Consumption: Muted <200 mA

Full Volume 700 mA

ENVIRONMENTAL

Temperature Range: -10˚C to 55˚C

Solar Radiation: Case UV stabilised

Water & Dust Resistance: TP67 excluding external

cabling

Compass Safe Distance: 300 mm

MECHANICAL

Dimensions: 164(W) x 65(H) x 55(D) mm

Weight: 450 grams

AUDIO OUTPUT POWER

External 4 Ohm Speaker: 4 Watts average

Internal Speaker: 2 Watts average

EXTERNAL CONNECTIONs

Microphone: 6 pin RJ12 Socket

D.C. Supply: 2 pin Polarized Blade Socket

External Speaker: 3.5 mm mini phono line

socket (mono)

OVERCURRENT PROTECTION

Fuse: Inline 2 Amp 3 AG

INsTALLATION

INsTALLING THE UNIT

After choosing your location, hold the unit with the

mounting bracket attached into the desired position and

mark the location with a pencil. Remove the mounting

bracket from the radio and drill the mounting holes. Bolt or

screw the bracket in place using hardware suitable for the

mounting surface. The unit is supplied with stainless steel

screws; however, if the mounting surface is unsuitable for

screws you may need to replace these with stainless steel

bolts. Remember the ﬁxings for overhead mounted units

may have to withstand heavy pounding when the vessel is

in rough water or being towed on a trailer.

sELECTING A LOCATION

It is advisable to spend a little time selecting the best

location for your RM600D. The mounting bracket can be

rotated above, below or behind the radio enabling the radio

to be mounted in a wide range of locations. In addition,

using the optional ﬂush mounting kits (MK600, MK001,

MK002) the RM600D can be mounted directly in a panel or

dashboard. The ﬂush mounting kits allow for installation or

replacement of any existing VHF radio.

REPLACING THE MICROPHONE

It is recommended that the microphone be left permanently

connected to the RM600D, but if it must be disconnected,

proceed as follows:

1. Insert a small screw driver between the rubber boot

and the lip of the raised area on the front panel.

2. Ease the rubber boot out of the cable entry hole and

slide it along the cable away from the front panel.

3. Identify the plug locking lever, work the screwdriver

blade behind it and move the lever towards the plug

body. At the same time gently pull the plug from the

socket. (see diagram below).

If required, replacement microphones are available with

plug and rubber boot already ﬁtted.

WATER PROOFING CONNECTIONs

Although the RM600D itself is designed to resist the

ingress of water, the cable connectors are not completely

waterproof. After installation, the speaker and remote

connectors should be wrapped in waterproof tape or similar

to minimise the risk of corrosion or water damage. Do

not use normal electrical tape as this will not provide an

adequate seal against water. The connectors should then

be positioned where they are not directly exposed to the

elements.

Cable

Screwdriver

Locking Lever

move to left to

release Plug

Cable entry hole

A Division of:

Head Ofﬁce: sYDNEY- Locked Bag 2086, North Ryde N.S.W. 1670, Australia. Tel: +61 2 9844 6666, Fax: +61 2 9844 6600.

MELbOURNE ADELAIDE PERTH bRIsbANE sYDNEY AUCkLAND

7 Mircro Circuit 14 Phillips St. Unit 1 Unit 1 Unit B Unit F

Dandenong South Thebarton 10-12 Harvard Way 89-101 Factory Rd. 22-24 College St. 35 Neilpark Dr.

Vic. 3175 S.A. 5031 Canning Vale Oxley Gladesville East Tamaki

Tel: +62 3 9798 0988 Tel: +61 8 8234 2633 W.A. 6155 Qld. 4075 N.S.W. 2111 N.Z. 2141

Fax: +62 3 9798 0177 Fax:+61 8 8234 5138 Tel: +61 8 9455 5744 Tel: +61 7 3278 6444 Tel: +61 2 9879 8888 Tel: +64 9 274 0955

Fax: +61 8 9455 3110 Fax:+61 7 3278 6555 Fax: +61 2 9816 4722 Fax: +64 9 274 0959

For customers outside Australia and New Zealand, please contact your local GME retailer or email to: [email protected]

Part Number: 310351 Drawing Number: 4 3 9 0 1 - 2 www.gme.net.au

NATIONAL DIsTRIbUTOR DETAILs:

GME limit this warranty to the original purchaser of the

equipment.

GME warrant the RM600D to be free from defects in

material and workmanship for a period of twelve (12)

months from the date of purchase from their authorised

retailer.

Should the product require servicing during this period,

all labour and parts used to effect repairs will be supplied

free of charge. GME reserve the right to determine whether

damage has been occasioned by accident, misuse or

improper installation whereby the warranty would be void,

including equipment which has been damaged due to:

(a) Incorrect or reverse polarity connection to a battery or

power supply or to an incorrect supply voltage.

(b) Operation of the main unit GX600 without an

antenna or by connection to an antenna which has

been incorrectly installed, resulting in damage to

the radio’s output circuit.

Procedure to be followed by Claimant: In the event of a

defect occurring during the warranty period, the original

purchaser may return the defective unit along with suitable

proof of purchase date (i.e. receipt, docket, credit card slip

etc.) and a full description of the defect to the retailer from

whom the unit was purchased. All freight charges incurred

for transportation by the retailer or GME are the purchaser’s

responsibility.

GME AFTER sALEs sERVICE

Your GME radio is especially designed for the environment

encountered in marine installations. The use of all solid

state circuitry, careful design and rigorous testing, result in

high reliability. Should failure occur however, GME maintain

a fully equipped service facility and spare parts stock to

meet the customer’s requirements long after expiry of the

warranty period.

WARRANTY

Andere GME Zwei-Wege-Funkgerät Handbücher

GME

GME TX6155 Bedienungsanleitung

GME

GME TX610 Leitfaden

Beliebte Zwei-Wege-Funkgerät Handbücher anderer Marken

Midland

Midland 70-1526A/B Bedienungsanleitung

HYT

HYT TC700 Bedienungsanleitung

DNT

DNT Space100 Bedienungsanleitung

Legacy

Legacy ProLine Series Bedienungsanleitung

Evolveo

Evolveo FreeTalk XM2-2 Bedienungsanleitung

AWC

AWC AWR1688+ Bedienungsanleitung

Motorola

Motorola XT665d Bedienungsanleitung

Cobra

Cobra 2-Way Radio Bedienungsanleitung

Klutch

Klutch KR-400 Bedienungsanleitung

Garmin

Garmin Rino 655t Bedienungsanleitung

Motorola

Motorola TLK 150 Bedienungsanleitung

Midland

Midland MXT275J Bedienungsanleitung

Titan

Titan TR200 Bedienungsanleitung

Cobra

Cobra CXT645 Bedienungsanleitung

Tait

Tait TM9100 Bedienungsanleitung

Yaesu

Yaesu FT-65R Bedienungsanleitung

Motorola

Motorola ASTRO SRX 2200 Series Bedienungsanleitung

Motorola

Motorola T5583 Bedienungsanleitung