Go Power GP-LiFePO4-100 Bedienungsanleitung
GP-LiFePO4-100
Lithium Battery
Quick Start Guide
Find tech tips, manuals and support at gpelectric.com
Only wire 4 batteries maximum in parallel
Do not get wet
Only suitable for 12-volt applications
Do not wire in series
Battery Specications
SPECIFICATIONS
Technology Lithium Iron Phosphate
Nominal Voltage 12.8 V
Rated Capacity
77°F (25 ±5 °C)
100 Ah @ 20A (5hr run time); 92 Ah @ 50A
(1hr 54 min run time; 92 Ah @ 100A (55 min
run time)
Capacity Correction for
Temperature Variations
-4 °F (-20°C) 60%
131°F (55°C) 95%
Maximum Discharge
Current
100A (continuous)
120A (30 minutes)
150A (5 seconds)
Specic Energy Density 121.9 Wh/kg
Volumetric Energy Density 96.1 Wh/L
Internal Resistance ≤ 7.5 mΩ
Terminals M8 insert
Torque: 10.8 - 12.7 Nm (95.59 - 112.40 lbs)
Charge Voltage 14.6V
Maximum Charge Current 100A
≤1500 @ 100% Depth of Discharge; ≥3000
@ 80%; ≥4500 @ 30%
UN 38.3; CE
Charge Cut-off Voltage
Cycle Life - 77°F (25°C)
14.6V
Discharge Cut-off Voltage 8.4V
Operating Temperature Charge: 32°F (0°C) to 131°F (55°C
Discharge: -4°F (-20°C) to 131°F (55°C)
Storage Temperature
1 Week: -4°F (-20°C) to 122°F (50°C)
1 month: -4°F (-20°C) to 113°F (45°C)
6 months1: -4°F (-20°C) to 104°F (40°C)
1Max storage time before recharge is 6 month.
Humidity
3mA
BMS Leakage Current
Length 12.9 in / 328 mm
Width 7 in / 178 mm
Height 9.2 in / 233.7 mm
BCI Group # 31
Weight 36 lbs / 16.33 kg
Carrying Nylon Strap
Operating: 5% to 90 % RH
Storage: 45% to 85% RH
Wiring Guide
The illustrations below show how to properly wire lithium batteries.
Minimum 1in gap inbetween batteries and
between batteries and battery enclosure walls
All battery interconnects to
be equal length and gauge
100Ah Lithium Battery Bank Parallel Connection
Note: Up to a maximum 4x 100Ah lithium batteries may be connected in parallel.
Lithium batteries may not
be connected in series. New batteries should never be connected to old batteries. All batteries should be charged to
a minimum of 13V before connecting them together.
Connect negative terminals together
Connect positive terminals together
All battery to busbar
connections to be equal
length and gauge
Ex) Inverter
Ex) Converter
Ex) Solar Controller
All busbar connections to external devices (inverter,
converter, solar controller, etc.) to be
equal length and gauge, sized appropriately for each device with suitable positive circuit protection
(fusing or breakers).
Positive busbar
Negative busbar
All battery interconnects, busbar and device connections to resist vibration by using nylon
insert lock nuts, thread locking fluid, or lock washers (split lock or external tooth).
Split lock washer
External tooth
lock washer
Do NOT stack smaller
terminals under large ones
Battery Bank Terminal Connections
Ensure correct strip length and that
stripped wires are completely inserted
into terminal before crimping
Minimum 1in gap inbetween batteries
Torque battery terminals to
11-14.7 N*m ( 97.3-130 in*lbs)
Terminals with open-end crimp
barrels may be used to verify wires
are fully inserted before crimping
Andere Go Power Kamerazubehör Handbücher
