Gold Apollo VP200 Montageanleitung

Voice Pager

MODEL：

：：

：VP200

VP200 Firmware Update

Contents

March 16, 2007

VP200

V1.

Contents

Getting Started...................................................................................................................................................1

Equipment Required .................................................................................................................... 1

Programming Setup ..................................................................................................................... 1

Programming the microprocessor....................................................................................................................6

Introduction.................................................................................................................................. 6

Start the Programming................................................................................................................. 6

VP200 Firmware Update

Getting Started

March 16, 2007 1

VP200

Getting Started

The FlashSta.exe provides is used to upgrade the VP200’s firmware. To obtain the best

results from the product, please take a few minutes to read this instruction guide.

Equipment Required

To re-program the VP200, you must meet the following minimum requirements:

A personal computer (PC) with USB port.

Windows 98 SE or above operating system (XP Recommended).

A USB cable – Type A to B.

VP200 Firmware Programmer.

The updating files for the microprocessor (extension *.s2 *.id).

The programming software FlashSta.exe.

The VP200 Programming Software.

Programming Setup

Software setup

If you have already installed VP200 Programming Software please omit this

step. You must install the software before installation the VP200 Firmware

Programmer. When the software installation is completed, you must to

restart your computer.

Hardware setup

Connect the USB cable to the USB port on your computer.

Plug the other end of the USB cable into the VP200 programmer.

To check which the COM port assignment made by Windows for the USB to

Serial adapter.

VP200 Firmware Update

Getting Started

March 16, 2007 2

VP200

1. Open up your “System Properties”

Click “Start” right-click on "My Computer" click the “Properties”

VP200 Firmware Update

Getting Started

March 16, 2007 3

VP200

Click “Start” “Control Panel” “System”

(Note: The COM port assignment of the USB to Serial adapter varies on your computer

hardware configuration. Windows will check what COM port are unused or free in your

computer and assigns that port number to the device.)

VP200 Firmware Update

Getting Started

March 16, 2007 4

VP200

2. Click the “Hardware” tab Click the “Device Manager” button and wait

for the “Device Manager” dialogue box to appear.

VP200 Firmware Update

Getting Started

March 16, 2007 5

VP200

3. Click the "+" by "Ports (COM & LPT)". You should see the Prolific

USB-to-Serial Comm Port (COM3) device listing. This also means that

Windows has assigned the device to COM3 port..

VP200 Firmware Update

Programming the microprocessor

March 16, 2007 6

VP200

Programming the microprocessor

Introduction

The following describes the procedures for using the VP200 firmware update to

accomplish the following:

1. Establish a computer hardware configuration.

2. Turn off the VP200 by rotating the ON-OFF SWITCH/VOLUME CONTROL

counterclockwise until a click is heard and the mechanical stop is reached.

3. Hold down the belt clip gentle and set the VP200 inside the VP200

Programmer.

4. Rotate the ON-OFF SWITCH/VOLUME CONTROL clockwise to turn on the

alert VP200. If you hear beep sounds or vibrator after turn on the pager, it

means bad connection, please confirm the VP200 is set on the programmer

tray and USB is connected to a computer properly.

Start the Programming

1. Copy in a folder of your PC the updating files (VP200.s2 and VP200.id).

2. Run the FlashSta.exe program, wait for the “Select Program” dialogue box to

appear, select the serial port of your PC connected to the device and select

the “Internal flash memory” option. Click on the “OK” button and wait for the

“ID Check” dialogue box to appear.

VP200 Firmware Update

Programming the microprocessor

March 16, 2007

VP200

V1.

3. If the “ID Check” window does not appear and the following window appears,

this means that there has been a communication failure to the VP200. Click

“Cancel” to close FlashSta.exe. Check that the VP200 is set on the

programmer tray, the cable connections from the PC to the VP200

Programmer have been made correctly, and the correct COM port has been

selected.

4. Click on the “Refer…” button to select the updating file VP200<version>.s2.

VP200 Firmware Update

Programming the microprocessor

March 16, 2007 8

VP200

5. Click on the “OK” button and wait for the ‘M16C Flash Start’ dialogue box to

appear.

Andere Handbücher für VP200

Inhaltsverzeichnis

Andere Gold Apollo Pager Handbücher

Gold Apollo

Gold Apollo AL-A07 Bedienungsanleitung

Gold Apollo

Gold Apollo AL-A28 Betriebsanleitung

Gold Apollo

Gold Apollo VP200 Betriebsanleitung

Gold Apollo

Gold Apollo AL-A25 Betriebsanleitung

Gold Apollo

Gold Apollo AL-A26 Betriebsanleitung

Gold Apollo

Gold Apollo AL-924 Betriebsanleitung

Gold Apollo

Gold Apollo AL-A26 Betriebsanleitung

Gold Apollo

Gold Apollo AL-A27 Betriebsanleitung

Gold Apollo

Gold Apollo AP-700 Bedienungsanleitung

Gold Apollo

Gold Apollo AL-A27 Bedienungsanleitung

Gold Apollo

Gold Apollo AL-A25 Betriebsanleitung

Beliebte Pager Handbücher anderer Marken

Alpha

Alpha Elite Bedienungsanleitung

LRS

LRS RX-E467 Bedienungsanleitung

unication

unication E3 Bedienungsanleitung

Infostream

Infostream X5 Montageanleitung

Motorola

Motorola BR850 Bedienungsanleitung

ACE TELECOM

ACE TELECOM ACE-2040 Bedienungsanleitung

Intek

Intek Allure Bedienungsanleitung

Pocsag

Pocsag PG-2092P Bedienungsanleitung

Motorola

Motorola Bravo classic Bedienungsanleitung

Motorola

Motorola LS750 Bedienungsanleitung

Alert Systems

Alert Systems HyperGuard MP10D Bedienungsanleitung

Motorola

Motorola Talkabout T900 Bedienungsanleitung

Motorola

Motorola Advisor Graphix CP1250 Bedienungsanleitung

Radio Shack

Radio Shack 17-7040 Bedienungsanleitung

PageOne

PageOne Advisor Graphix Bedienungsanleitung

Syscall

Syscall Nttworks GP-210RT Bedienungsanleitung

unication

unication G4 Bedienungsanleitung

GE LBI-31482 Bedienungsanleitung