Goldair GHP100 Bedienungsanleitung

Operating Instructions

HeatPump

Model: GHP100, GHP200, GHP300

General Care and Safety Guide

Thank you for choosing a Goldair Heat Pump. This Goldair Heat has been

designed and manufactured to high standards of engineering and with

proper use and care, as described in this leaflet, will give you years of

useful service. Please read these instructions carefully.

1. Use only the voltage specified on the rating

label of the unit.

2. Keep all objects at least 1 metre from the

front and sides of the unit. Do not place unit

close to radiant heat source.

3. Do not operate in areas where petrol, paint

or other flammable liquids are used or

stored.

4. Do not insert or allow foreign objects to

enter any ventilation or exhaust opening, as

this may cause an electric shock, fire or

damage to the unit. Do not sit on the unit.

5. Do not operate this unit with a damaged

cord, plug or after the unit malfunctions or

has been dropped or damaged in any

manner. contact the Goldair Customer

Services Team to arrange examination,

electrical service or repair.

6. This unit is intended for household use only

and not for commercial or industrial use.

7. Use this unit only as described in this

manual. Any other use is not recommended

by the manufacturer and may cause fire,

electrical shock or injury.

8. The common cause of overheating is

deposits of dust or fluff in the unit. Ensure

these deposits are removed regularly by

unplugging the unit and vacuum cleaning

the air vents and grills.

9. Do not use abrasive cleaning products on

this unit. Clean with a damp cloth (not wet)

rinsed in hot soapy water only. Always

remove plug from the mains supply before

cleaning.

10. Do not connect the unit to mains supply until

completely assembled and adjusted.

11. Ensure the Heat Pump is installed on a flat,

stable, heat-resistant surface.

12. Do not install the Heat Pump directly

above or below any power socket or

switch.

13. This unit is not intended for use by persons

(including children) with reduced physical,

sensory or mental capabilities or lack of

experience and knowledge, unless they

are supervised or have been given

instruction concerning the use of the unit

by a person responsible for their safety.

14. Do not use this unit in the immediate

surrounds of a bath, a shower, or a

swimming pool or other liquids. The unit

must not be immersed in any liquids.

15. When the unit has been unpacked, check it

for transport damage and ensure all parts

have been delivered. If parts are missing

or the unit has been damaged, contact the

Goldair Customer Services Team.

16. If your unit does not work, or is not working

properly, contact the place of purchase or

the Goldair Customer Services Team.

Repair work on the unit by unqualified

persons can cause serious risk to the user.

17. There are no user serviceable parts

installed in the unit.

18. Do not place the unit in wardrobes or other

enclosed spaces as this may cause fire

hazards.

19. This unit is not supposed to be used in or

around locations where foodstuffs, works

of art or delicate articles of science, etc are

stored.

20. Indoor use only.

21. Children should be supervised to ensure

that they do not play with the unit.

22. It is important that you do not cover this

heat pump.

TECHNICAL SPECIFICATION

Model No: GHP100, GHP200, GHP300

Supply: 220-240VAC 50Hz

Wattage: GHP100 –660/680W GHP200 1490/1580W GHP300 1940/2060W

Overview of your Heat Pump

1. Side clip to access manual

operation

2. LED Control panel

3. Horizontal louvres (for manual

adjustment only)

4. Air outlet

5. Oscillating louvre

6. Air inlet

7. Air outlet

8. Connecting pipe & cable

9. Stop valve

CONTROL PANEL

Heat pumps draw heat from air outside to heat a home, transferring heat

rather than running an element to create it. This can be reversed in

summer, so that the unit is used to cool the room.

Remote Sensor Timer

indicator

Defrost/Temperature

adjusting indicator Temperature

indicator Power

on/off

INDOOR UNIT

OUTDOOR UNIT

Overview of your Heat Pump

REMOTE

For best results, aim the remote directly at the

remote sensor on the control panel.

The remote has a 5 metre range of operation.

The remote control requires 2x AAA batteries

(included). Remove the plastic tab from the rear

of the remote to install batteries.

1. Temperature increase

2. Temperature decrease

3. Mode

4. Swing

5. Reset

6. Air Direction (oscillating louvre)

7. LED display

8. Fan speed

9. Power on/off

10. Timer on

11. Sleep

12. Timer off

13. Lock

14. Turbo

MEMORY FUNCTION

If power supply is cut off when the appliance is

running, or when the unit is powered off, it will

automatically restart in the last working mode

once power is restored.

REMOTE CONTROL PANEL

The control panel on the Remote indicates the

Heat Pump mode and function.

1. Temperature indicator

2. Transmitting indicator (blinks

when the remote transmits to

the indoor unit control panel)

3. Power on/off indicator

4. Operation mode indicator

5. Lock indicator

6. Timer indicator

7. Fan speed indicator

NOTE: You will hear a beep each time a

remote control button is pressed, as it

transmits to the indoor unit control panel.

Goldair heat pumps are covered under warranty only when a Goldair

Approved Installer has completed the install, any heat pump not installed

by a Goldair Approved Installer will void its warranty.

(°C)

Operating your Heat Pump

Always choose a safe location for the Heat Pump, keeping in mind the

safety precautions outlined. Ensure all packaging has been removed from

the unit before use.

WARNING Keep all objects at least 1 metre from

the front and sides of the unit.

Note: When the Heat Pump is turned on for the first

time, it may release a slight odour or mist, or

cracking noise. This is a normal occurrence caused

by the initial heating of the internal components and

should not occur again.

OPERATION

Once the Heat Pump has been installed by a

Goldair approved installer, check that the batteries

of the remote are inserted correctly before

attempting to power the unit on.

Press the Power button on the Remote to turn the

unit on. The power on/off indicator will display on

the control panel.

The LED on the control panel will display the default

temperature of 24°C and begin to blow out air on

Low fan speed in heat mode.

Note: When the unit is powered on it may take

several minutes to heat to the set temperature

before begging to blow air. This is normal, and is

indicated on the control panel by the

Defrost/Temperature adjusting indicator being

illuminated.

To turn the unit off, press the Power Button again.

Note: When the unit has been powered off the fan

will continue to run as the unit shuts down. This is

normal, and assists to prolong the life of the unit.

This can be overridden by pressing the Power

button a third time.

THERMOSTAT

Press the arrow up or arrow down buttons to adjust

the temperature to your desired setting (from 17-

30°C). Once you have set the desired temperature,

the LED on the control panel will blink and then

display the new set temperature. The unit will now

work to adjust the room temperature to the set

temperature.

FAN SPEED

Press Fan Speed button to switch between the

following:

AUTO - HIGH - MED - LOW

In AUTO mode, the fan speed will cycle between

low, medium and high to achieve the set desired

room temperature.

MODE

Press Mode button to switch between the following:

AUTO - COOL - DRY - HEAT - FAN

In AUTO mode, the fan speed will cycle between

low and high to maintain the set temperature, and

cannot be adjusted. When the unit is run in this

mode, AUTO indicator will illuminate on the Control

Panel.

In COOL mode, water may drip from the unit if it has

been running non-stop for an extended period of

time, it is recommended if this condensation occurs

to adjust the louvre to vertical and adjust the fan

speed to high.

In DRY mode, the fan speed cannot be adjusted.

When the room temperature is lower than 10°C in

this mode, the unit will automatically stop

dehumidifying until the room temperature increases

again.

In HEAT mode use the High fan speed setting

initially and then switch to the Low speed setting for

greater economy.

In FAN mode, the temperature cannot be adjusted.

When switching between modes, the unit will pause

as it re-adjusts, this is indicated by the LED

Defrost/Temperature adjusting indicator displayed

on the Control Panel. Once the unit has adjusted

the internal temperature, the fan will begin to blow

air at the set temperature, note that this pause while

the unit re-adjusts may take several minutes.

SLEEP

When the SLEEP button is pressed, the unit will

change the fan speed to low.

Sleep setting can only be set in AUTO - COOL -

HEAT modes. When Sleep is selected in Cool or

Heat modes the unit will adjust the set temperature

by 1-2°C per hour for the first 2 hours of operation,

and then remain for the next 5 hours before the unit

switches off automatically.

Operating your Heat Pump

TIMER

The Heat Pump is fitted with a timer that will turn the

unit on or off after the desired time has elapsed.

To set the unit to turn on:

Press the TIMER ON button to adjust the length of

time from 1 –24hours that you would like the unit to

run for before turning on. Each press of Timer On

button will adjust the length of time before the unit

switches on. The first 1-10 hours will adjust in 30

minute increments with each press of the Timer On

button, the remaining 11-24 hours will adjust in 1

hour increments.

To turn off the Timer setting function, set the Timer

On back to 0hours.

This function can be set while the unit is running, or

when the unit is powered off.

When the unit is powered on, and the TIMER ON

function is set, the unit will turn back on after the set

length of time, only after the unit has been powered

off.

To set the unit to turn off:

Press the TIMER OFF button to adjust the length of

time from 1 –24hours that you would like the unit to

run for before turning off. Each press of Timer Off

button will adjust the length of time before the unit

switches off. The first 1-10 hours will adjust in 30

minute increments with each press of the Timer Off

button, the remaining 11-24 hours will adjust in 1

hour increments.

To turn off the Timer setting function, set the Timer

Off back to 0hours.

Do not use this Heat Pump with a programmer,

remote-control system, separate timer or any other

device that switches the Heat Pump on

automatically.

LED DISPLAY

By pressing the LED button the LED on the control

panel which switch off but the unit will continue to

run.To illuminate and view the LED display again,

press the LED display button a second time.

SWING

This button turns the unit oscillation function on and

off.

AIR DIRECTION

The louvre can be manually adjusted to the desired

angle by pressing this button.

Note: The louvre will automatically close when the

unit is powered off.

HORIZONTAL LOUVRE

The Heat Pump is fitted with 3 horizontal louvres

than can be manually adjusted at the unit only.

TURBO

This function operates in Cool mode only.

By pressing the TURBO button the unit will change

the fan speed to high, and work to cool the room

faster. Press the Turbo button again to cancel this

function.

RESET

When the recessed RESET button is pressed all

current settings are cancelled and the unit will begin

to operate in the default settings.

LOCK

When the recessed LOCK button is pressed the

controls will not be able to be changed. Press the

Lock button again to cancel this function and enable

the controls.

DEFROST

Occasionally the air around the motor can become

very cool, this will cause the unit to go into defrost

mode. The Defrost/Temperature adjusting indicator

light will illuminate on the control panel.

This is a normal function for the Heat Pump and

cannot be controlled by the user.

Cleaning and Maintenance

MANUAL OPERATION

By pressing the left and right Side clips in together

on the Indoor unit, and lifting the unit front panel,

the manual switch can be accessed. The Manual

Operation should only be used when maintenance

is being performed on the unit, or the Remote fails

to operate.

CARE AND CLEANING

The Heat Pump requires regular cleaning to ensure

trouble free operation:

Ensure that the Heat Pump has been allowed to

Power Off completely before cleaning.

Switch the Heat Pump off from the mains supply

before cleaning.

Use a damp cloth (not wet) to wipe the exterior of

the Indoor unit to remove dust and dirt.

Use a vacuum cleaner to remove dust and fluff from

around the grill/louvre.

Never use solutions such as benzene, thinners or

polishing agents.

Ensure the Heat Pump is dry before switching back

on at the mains supply.

TO CLEAN THE AIR FILTER:

Ensure that the Heat Pump has been allowed to

Power Off completely and has been switched off

from the mains supply.

Press the left and right Side clips in together on the

Indoor unit, and lift the unit front panel.

Remove the filter by pressing the Filter clip in and

gently pulling the filter down and out of the unit.

Clean the filter with a vacuum or with water. Dry the

filter.

The Freshening filter sits in behind the air filter and

can be removed by gently pulling out from its frame.

Clean the freshening filter with a vacuum or with

water. Dry the filter.

Ensure both the air filter, and freshening filter are

completely dry before placing back in the unit.

Never use unit without the air filter and freshening

filter.

IMPORTANT! NEVER COVER THIS HEAT PUMP!

CAUTION

Do not touch the metal parts of the unit when

removing the filters. Injuries can occur when

handling sharp metal edges.

Do not use water to clean inside the unit. Exposure

to water can destroy the insulation, and lead to

possible electric shock.

Do not attempt to dismantle the Heat Pump. There

are no user serviceable parts. For service or repair,

contact an authorised electrical service technician.

CAUTION: The Heat Pump generates heat during

use. Proper precautions must be taken to prevent

the risk of burns, scalds, fires or other damage to

persons

It is important that you do not cover this Heat Pump.

STORAGE

If you do not plan to use the unit for a long period of

time the follow steps can be performed to care for

the unit:

•Clean the indoor unit and filters.

•Operate the fan for about half a day to dry the

inside of the unit.

•Power off the unit and switch off at the mains

supply.

•Remove the batteries from the remote control

unit.

•The outdoor unit requires periodic maintenance

and cleaning; Do not attempt to do this yourself

contact your authorised service technician.

PROOF OF PURCHASE

To receive warranty retain receipt as proof of

purchase. (Refer to back of booklet).

Goldair –New Zealand

Monday –Friday 8am-5pm

Phone +64 (0)9 917 4000

Phone 0800 232 633

[email protected]z

Goldair –Australia

Monday –Friday 8am-5pm

Phone +61 (0)3 9336 4423

Phone 1300 465 324

info@cdbgoldair.com.au

SUPPORT AND TECHNICAL ADVICE

Trouble shooting

The following events may occur during normal

operation.

The unit will not restart for 3-4 minutes after it

stops

The unit is designed not to blow cold air on HEAT

mode. This may occur when the indoor heat

exchanger is in one of the following three situations

and the set temperature has not been reached.

1. When heating has just started.

2. Defrosting.

3. Low temperature heating.

The indoor or outdoor fan stop running when

defrosting

Frost may be generated on the outdoor unit during

heat cycle when the outdoor temperature is low and

humidity is high resulting in lower heating efficiency

of the Heat Pump.

During this time the Heat Pump will stop heating

operation and start defrosting automatically.

The time to defrost may vary from 4 to 10 minutes

according to the outdoor temperature and the

amount of frost built up on the outdoor unit.

A white mist coming out from the indoor unit

This may generate due to a large temperature

difference between air inlet and air outlet on COOL

mode in an indoor environment that has a high

relative humidity.

A white mist may generate due to moisture

generated from defrosting process when the Heat

Pump restarts in HEAT mode operation after

defrosting.

Low noise emitting from the Heat Pump

You may hear a low hissing sound when the

compressor is running or has just stopped running.

It is the sound of the refrigerant flowing or coming to

a stop.

You can also hear a low "squeak" sound when the

compressor is running or has just stopped running.

This is caused by heat expansion and cold

contraction of the plastic parts in the unit when the

temperature is changing.

A noise may be heard due to louver restoring to its

original position when power is turned on.

Dust is blown out from the indoor unit

This is a normal condition when the Heat Pump has

not been used for a long time or during first use of

the unit.

A peculiar smell comes out from the indoor unit

This may be caused by the indoor unit giving off

smells permeated from building material, from

furniture, or smoke.

The Heat Pump turns to FAN only mode from

COOL or HEAT mode

When indoor temperature reaches the set

temperature the compressor will stop automatically,

and the Heat Pump turns to FAN only mode. The

compressor will start again when the indoor

temperature rises on COOL mode or falls on HEAT

mode.

The Heat Pump runs after turning off the unit

When turning off the unit under COOL (AUTO

COOL, FORCED COOL) and DRY mode, the Heat

Pump will run for 7-10 minutes, then stop the

operation and turn off the unit automatically.

Dripping water may condensate on the surface of

the indoor unit when cooling in a high relatively

humidity (relative humidity higher than 80%). Adjust

the horizontal louver to the maximum air outlet

position and select HIGH fan speed.

Heating mode

The Heat Pump draws in heat from the outdoor unit

and releases it via the indoor unit during heating

operation. When the outdoor temperature falls, heat

drawn in by the Heat Pump decreases accordingly.

At the same time, heat loading of the Heat Pump

increases due to larger difference between indoor

and outdoor temperature. If a comfortable

temperature can't be achieved by the Heat Pump,

we suggest you use a supplementary heating

device.

Auto-restart function

Power failure during operation will stop the unit

completely.

When the power restores, the OPERATION

indicator on the indoor unit starts flashing. To

restart the operation, push the ON/OFF button on

the remote controller, the unit restarts automatically

with all the previous settings preserved by the

memory function.

Thank you for purchasing this Goldair product. Your product is warranted against faults and manufacture when used in

normal domestic use for a period of two years. In non-domestic use Goldair limits the voluntary warranty to three

months.

Goldair undertake to repair or replace this product at no charge if found to be defective due to a manufacturing fault

during the warranty period.

This warranty excludes damage caused by misuse, neglect, shipping accident, incorrect installation, or work carried out

by anyone other than a qualified electrical service technician.

PLEASE KEEP YOUR RECEIPT AS THIS WILL HELP VERIFY YOUR WARRANTY.

The benefits given to you by this warranty are in addition to other rights and remedies available to you under law in

relation to the goods or services to which this warranty relates.

In Australia, our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are

entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or

damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

In New Zealand this warranty is additional to the conditions and guarantees of the Consumers Guarantee Act (1993).

Two Year Warranty

Goldair Two Year Warranty (IMPORTANT: Please complete and retain this warranty card)

Name

Address

Place Of Purchase Date of Purchase

Name Of Product Model Number

Attach a copy of the purchase receipt to this warranty card

Due to continual design improvements, the product illustrated in this User Manual may differ slightly from the actual product.

Goldair –New Zealand

CDB Goldair

PO Box 100-707

N.S.M.C

Auckland

Phone +64 (0)9 917 4000

Phone 0800 232 633

www.goldair.co.nz

Goldair –Australia

CDB Goldair Australia Pty

PO Box 574

South Morang

Victoria, 3752

Phone +61 (0)3 9336 4423

Phone 1300 GOLDAIR (1300 465 324)

www.goldair.com.au

Andere Handbücher für GHP100

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Goldair Wärmepumpe Handbücher

Goldair

Goldair GHP100 Bedienungsanleitung

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung