Golmar IP 6502/G+ Benutzerhandbuch

6502/G+

12327402

INSTALLER MANUAL

(Manual based on FW version 1.04)

CATEGORY 1_HEADERCATEGORY 2_HEADER

2Footer Infos

IP G+ 6502/G+

www.golmar.es 2

INDEX

1. Safety cautions and warnings ...........................................................................................................................3

2. Specications....................................................................................................................................................3

3. Panel description..............................................................................................................................................3

4. Panel installation .......................................................................................................................................................... 4

5. Initial conguration ..................................................................................................................................................... 5

6. Initial alternative conguration through web client................................................................................................ 6

7. Settings........................................................................................................................................................................... 8

8. System operation.......................................................................................................................................................... 9

9. Installation diagram..................................................................................................................................................... 10

6502/G+ IP G+

www.golmar.es

- TCP/IP video intercom system with technology IP-G+.

- Installation over existing ethernet network (D4L-G+/POE are required).

- Up to 98 blocks in one system.

- Up to 19 entry panels at each block.

- Up to 19 general panels at each installation.

- Up to 799 ats per each block.

- Up to 19 guard units for the general compound and 9 guard units at each block.

2. SPECIFICATIONS

3. PANEL DESCRIPTION

- e installation and setup of this equipment must be done by an authorized installer.

- e current regulations oblige to protect the power supply by means of a thermal magnetic circuit breaker.

- All the installation conduits must distance at least 40 cm from any other installation.

- In regards of the power supply FA-G+:

- Do not tight with excessive strength the screws of the terminal block at FA-G+ power supply.

- Install the power supply in a dry and secure area, protected against water drops.

- Avoid placing the power supply close to heating sources, humid or dusty areas.

- Do not cover the power supply ventilation openings area to assure air ow circulation.

- To prevent damages, the power supply has to be strongly mounted. Use a DIN rail 46277 (8 DIN) to x it.

-To avoid an Electrical shock, do not remove the protection cover and do not manipulate the cables connected to the power terminals.

1. SAFETY CAUTIONS AND WARNINGS

09:27

06-03-2020

Screw to x the header

Header

Door panel xation

RJ-45 conector

NC1

NA1

GND

+12V

AP+

AP-

NA2

NC2

- Front

- Connections terminal block.

(*) Anti-vandal tamper.

RFID reader

Light sensor

IK-07 and IP-65

Working temperature: -40~60ºC

Navigation menu

4,3” LCD TFT, 480x272 px.

Numeric Keypad

White leds for night vision

130 º wide angle camera

Exit button

Local power supply input

NO, NC door release

dry contacts.

Sensor IR

N.O, N.C door release

dry contacts

(**) In case to power the panel with a local power supply, the ethernet cable cannot be connected to a PoE output of the distributor

D4L-G+.

6502/G+IP G+

www.golmar.es

1 -Avoid locating the panel exposed to direct sun light or ex-

ternal light sources like streetlamps, to get a good image.

4. PANEL INSTALLATION

3- Make a hole in the wall where to t the embedding box CE-

6502/G+. e dimensions of the hole are 128(W) x 306 (H) x 44

(D). Assure the box is xed upside correctly.

2- Locate the top part of the entry panel at 1,65m height from

ground.

09:27

06-03-2020

Mind the embedding box orienta-

tion.

It is recommended to oow the

instructions andtips mentioned in

the embedding box mount guide:

(https://bit.ly/3incuSb)

4- Connect the ethernet cable (1) and hang the upper part of the

panel in the nails which protrude out of the box (2), then tilt the

panel to t into the bottom part of the box.

5- Fix the bottom part of the panel using the screws supplied. 6- Slide up the header supplied, to cover the bottom part of the

panel and tight the screws underneath.

09:27

06-03-2020

09:27

06-03-2020

09:27

20-09-2017

(*) Header screw should be tight using the supplied tool.

Registro correcto. El sistema se reiniciará ahora

6502/G+ IP G+

www.golmar.es

Marcar el número de vivienda

o pulsar para mostrar la agenda

Introducir longitud del código de llamada (5 o 6 dígitos)

Introducir contraseña

Introducir número de edicio (1 a 99)

Menú de ajustes

Introducir número de placa (1 a 19)

Ajustes de la placa

Registro correcto. El sistema se reiniciará ahora

Select automatic IP assignment. In

this way the system will assign to the

master panel 10.0.14.9 IP address

In this moment, panel will reboot

and will be congured like man-

ager panel.

For a manual assignment of the IP address, follow the same process as described above, but in step 8 choose the Manual mode, then

follow the steps described below:

Registro correcto. El sistema se reiniciará ahora

Enter the desired IP address of

the panel and press validation

icon.

Registro correcto. El sistema se reiniciará ahora

Enter subnet mask and press

validation icon.

Registro correcto. El sistema se reiniciará ahora

Enter Gateway address and press

validation icon.

Registro correcto. El sistema se reiniciará ahora

Enter the IP Server address.

It is IP address of the system

manager panel.

Once all the steps have been completed, will appear the same conrmation screen as in automatic option.

Access to conguration. Type the installer PIN code

“2718” with the keypad and press validation

Select the second option in

settings menu (1/3).

Select second option in settings

menu (1/2).

Select 5 digits dialling length.

*6 digits dialling code length in the

case you like to indicate the oor

Type “1” for building number and

press validation icon.

Type “1” for panel number and

press validation icon.

- One of the panels of the installation is in charge to manage the system, thus it is not necessary to assign IP addresses or to cong the

changes applied to each one of the devices of the installation.

To congure a panel as system manager, follow the steps:

5. INITIAL CONFIGURATION

CATEGORY 1_HEADERCATEGORY 2_HEADER

6Footer Infos

www.golmar.es

IP G+ 6502/G+

6502/G+ coded panel can be congured via its web client.

To do this, you need to connect your computer to the network.

e factory IP address of the panel is 10.0.0.254. Check that your computer network connection is in the same range. You will perform

the following steps:

It follows the explanations on how to review the registered conguration.

Marcar el número de vivienda

o pulsar para mostrar la agenda

Introducir contraseña

Menú de ajustes

Menú de ajustes (3/3)

1 2 3 4

Access to conguration. Type the installer PIN code

2718 with the keypad and press validate.

Press the right arrow button to

go to settings menu (3/3).

Select the fourth option.

Edicio

Placa

Dirección IP

Máscara de red

Puerta de enlace

Dirección Mac

Block and door panel

number set.

(*) Check the quick guide of the monitor to know the monitor’s conguration, in order to communicate with the panel.

In systems with general entry panels, will require to follow the same process described before, but in step 6, the number of building

should be 99. e number of entry panel will run from 1 to 19 (max. number of general entry panel is 19).

6. ALTERNATIVE INITIAL CONFIGURATION THROUGH WEB CLIENT.

Go to network settings in control panel. Change the active Ethernet network.

Enter into “properties”. 4Select Internet

protocol IPv4.

5Set the IP range.

IP address should start by 10.

Next three numbers should

have a value lower than 255.

Assign 10.0.0.1 as Gateway.

Do not assign DNS Conrm settings.

1 2

6502/G+ IP G+

www.golmar.es

Type the IP in the browser: Factory IP: 10.0.0.254

10.0.14.9

e password is 888999.

Now the computer is congured to work in the same IP range in which the panel is located.

e only thing le to do is to:

Now the initial screen of the web client is described:

On this initial screen, there are various sections on the bottom

right-hand side. For the system manager panel initial conguration,

you only will acceess to the “Settings” section.

You shall set out in descending order:

• Dialing code length: 5

• Block number: 1

• Panel number: 1

• Floor number: 1

You can also activate the villa mode, the tamper, in addition to

changing the date and time.

You will be able to establish panel IP address manually from this same screen.

Active the manual data input by clicking icon.

You must ll in the “Local IP” eld with the desired panel IP address, “Subnet Mask” eld with panel subnet mask, “Gateway” eld with

the Gateway address and “Server IP” eld with the server IP address.

Remember that, in system manager panel case, the server IP address is its own IP address.

Illumination leds*

TFT always ON

Prompt messages**

Speaker level

*Illumination modes

0OFF - 1ON - 2Auto

**Prompt modes

0OFF

1Spanish

2Danish

4English

5French

6Greek

7Portuguese

8Ring tones



By clicking “Next” tab, you will be taken to the next screen. Here you

will be able to set panel illumination modes, set whether you want to

keep the panel’s TFT always on or not and set the opening time of the

electric lock openers 1 and 2.

You also will be able to enable or disable prompt messages and set the

language in which they are reproduced.

NOTE: For more information about web client, visit its manual.

CATEGORY 1_HEADERCATEGORY 2_HEADER

8Footer Infoswww.golmar.es

IP G+ 6502/G+

- Language selection.

Select the language for the vocal messages and navigation menu. e available languages are English, Spanish, French, Dutch and

Portuguese.

7. SETTINGS

Marcar el número de vivienda

o pulsar para mostrar la agenda

1 2

Access to languages. Select the required one.

- Door panel volume adjustment

Marcar el número de vivienda

o pulsar para mostrar la agenda

Introducir contraseña

Menú de ajustes

Ajustes de la placa

1 2 3 4

Access to conguration. Type the installer PIN code

“2718” and press validation icon.

Select the second option from

settings menu (1/3).

Press the right arrow button to go to

door panel settings menu (1/2).

Ajustes de la placa (2/2)

Seleccionar el volumen del altavoz

5 6

Access to volume Adjust the volume to a level between

1-10 by using the arrows, once adjusted

select the fourth option to validate it.

- RFID cards.

Marcar el número de vivienda

o pulsar para mostrar la agenda

Introducir contraseña

Menú de ajustes

Menú de ajustes (2/3)

1 2 3 4

Access the conguration. Type the installer PIN code

2718 and press validation icon.

Press the right arrow button to

go to settings menu (2/3).

Select the second option in the

settings menu (2/3).

Tarjetas de acceso

09:27

20-09-2017

5 7

Select the second option,

access cards.

Swipe the cards which you like to link to this

apartment.

A maximum of 5 cards per apartment can be

(*) It is possible to delete or transfer the cards to other panels. To proceed, select the option or in the step 5.

Seleccionar o introducir el número de vivienda

VIVIENDA 5

VIVIENDA 4

VIVIENDA 3

VIVIENDA 2

VIVIENDA 1

Tarjeta añadida

6 8

Select the apartment to which associate

the access cards, once selected press the

validate button.

Once the card has been added, a

conrmation tone will be emitted.

e screen will display “card added”.

www.golmar.es 8

NL PT

6502/G+ IP G+

www.golmar.es

8. SYSTEM OPERATION

09:27PM

20-09-2017

CALLING

UNIT

CALLING

ADDRESSBOOK

BY UNIT

NUMBER

Marcar el número de vivienda

o pulsar para mostrar la agenda SERGIO SANCHO

ALBERT ESTOPA

MARC CUADRAS

JUAN FERNANDEZ

ANTONIO GARCÍA

Pulsar para iniciar la llamada

SEARCH UNIT

NUMBER

MOVE THROUGH

ADDRESSBOOK

09:27PM

20-09-2017

ADDRESS

CODE

OPEN

DOOR

PROXIMITY

ACCESS

CODE

Marcarel número de vivienda

opulsar paramostrar la agenda

(*) e push button allows to make a direct call to the available guard units.

e call process lasts for a maximum of 45 seconds. e panel will prompt the voice message ”call is in progress” and will display that

message on screen. If aer 45 seconds the call has not been answered, it will indicate “No response, try it later”.

e communication process lasts for a maximum of 90 seconds. From the time that the monitor picks up the call, the panel will

display “In communication”. Once the communication is nished, the panel will prompt a voice message “Communication is

nished” and will display that message on screen.

001

Monitor 1

Llamada en curso

No responde. Pruebe más tarde.

001Monitor 1

En comunicación

001Monitor 1

Comunicación nalizada

6502/G+IP G+

www.golmar.es

During a door release process, the panel will display on screen “Door is open”.

Puerta abierta

We can choose which door opener enable through the openning code entering, access card presentation or in a call process between

the door panel and the monitor in the next way:

Marcar el número de vivienda

o pulsar para mostrar la agenda

Introducir contraseña

Menú de ajustes

1 2 3

Access the conguration. Type the installer PIN code

2718 and press validation icon.

Press the third option

“Openning settings menu”.

Menú de ajustes

Ajustes de apertura

Abrepuertas 1 y 2

Apertura mediante código de acceso

5 6

Access to the fourth option

“Unlock with access code”

Choose between the four available

options: Disable, Lock 1 only, Lock 2

only or Lock 1 and 2.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere golmar Gegensprechanlage Handbücher

golmar

golmar Vista Nexa Bedienungsanleitung

golmar

golmar CETK-590 Plus Bedienungsanleitung

golmar

golmar T632 Bedienungsanleitung

golmar

golmar IP ART 7/G+/48 Bedienungsanleitung

golmar

golmar G2+ Bedienungsanleitung

golmar

golmar ART 7T/G2+ MONITOR Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

golmar

golmar G2+ Bedienungsanleitung

golmar

golmar S5110/ART 7W Bedienungsanleitung

golmar

golmar Art 7H/G2+ Bedienungsanleitung

golmar

golmar 50124319 Bedienungsanleitung

golmar

golmar GCALL Gebrauchs- und Pflegehandbuch

golmar

golmar GB2 Nexa Modular Bedienungsanleitung

golmar

golmar Stadio Plus T150i Bedienungsanleitung

golmar

golmar GB2 Nexa Modular Bedienungsanleitung

golmar

golmar Kit SOUL S5110/ART 4 LITE Bedienungsanleitung

golmar

golmar TSzena ML Bedienungsanleitung

golmar

golmar TEKNA HF GTWIN Bedienungsanleitung

golmar

golmar M201 Bedienungsanleitung

golmar

golmar GB2 Nexa Modular Bedienungsanleitung

golmar

golmar Stadio Plus T4003ML Bedienungsanleitung

golmar

golmar Platea Uno Bedienungsanleitung

golmar

golmar CE-ART 7/G2+ Bedienungsanleitung

golmar

golmar EL632/G+/48 Benutzerhandbuch

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung

Bticino

Bticino Classe 300 Bedienungsanleitung

golmar IP 6502/G+ Benutzerhandbuch

Beliebte Gegensprechanlage Handbücher anderer Marken