Good Way Hi-Flo CC-400HF Handbuch

CC-400HF

Hi-Flo®

COIL CLEANER

Operating and

Maintenance

Instructions

Read before operating.

CC-400HF HI-FLO 0121

CONTENTS:

INTRODUCTION ....................................................................................................................................2

IMPORTANT SAFETY INSTRUCTION............................................................................................... 3-4

ELECTRICAL PRECAUTIONS ...............................................................................................................4

OPERATING INSTRUCTIONS ...............................................................................................................5

GENERAL MAINTENANCE AND STORAGE .......................................................................................6

ACCESSORIES/SPARE PARTS...............................................................................................................6

SPECIFICATIONS ...................................................................................................................................6

TROUBLESHOOTING............................................................................................................................6

EXPLODED VIEW............................................................................................................................... 7-9

Thank you for purchasing Goodway’s CC-400-HF Hi-Flo® Coil Cleaner. We

appreciate your business and look forward to serving you in the future. As with

all Goodway products, you can be assured that the nest quality components and

workmanship have gone into this machine.

Please take a few minutes to read the following Operating and Maintenance

Instructions. Please pay particular attention to the safety instructions and exercise

caution when using this machine.

GOODWAY®TECHNOLOGIES CORPORATION

HVAC & FACILITY MAINTENANCE SOLUTIONS

For Sales Call: 1-800-333-7467

For Service Call: 1-800-370-2855

CC-400HF HI-FLO 0121 3

WARNING

IMPORTANT SAFETY INSTRUCTIONS

1. Read all instructions before using the unit. Failure to follow all instructions may

result in serious injury.

2. WARNING: Risk of injury: Do not direct discharge stream at yourself or

other persons!!

3. Always check the unit, hoses, ttings, etc. before each use. Do not use the unit if it

does not operate properly or has been damaged.

4. Do not use with gasoline or any other ammable liquid. Do not operate in

explosive atmospheres, such as in the presence of ammable liquids, gases

or dust.

5. If using chemical cleaners, make sure that there is adequate ventilation in the

work area.

6. Keep bystanders, children, and visitors away while operating this unit.

7. Do not use while tired or under the inuence of drugs, alcohol, or medication.

8. Do not overreach or stand on unstable support. Keep proper footing and balance

at all times.

9. Wear rubber gloves, rubber boots, goggles or face-shield, etc. Coil Cleaning

detergents, chemicals, and debris may cause injuries to the eyes and skin.

10. Call Goodway to check compatibility before using any chemical in the unit - DO

NOT use any cleaner that contains sodium hydroxide or potassium hydroxide. Do

not mix chemicals.

11. Use only Goodway-approved accessories and replacement parts.

12. Always turn machine off and relieve pressure in the hose after use.

13. Do not run the unit dry – it may damage the pump. Always ensure adequate

water supply.

14. Do not spray the unit with water or chemicals. Never expose the unit to rain. Store

unit indoors.

15. Do not allow the unit to freeze or leave in freezing temperatures.

CC-400HF HI-FLO 0121

16. The unit is equipped with an automatic by-pass valve that recirculates water inside

the pump when the spray gun trigger is released. Although the unit has a thermal

discharge valve for protection, avoid leaving the unit running in by-pass mode for

more than ve (5) minutes.

17. IMPORTANT: Do not carry the unit by the pump guard as it is not designed to be

used as a handle!!!

18. DO NOT ADJUST BYPASS PRESSURE: The bypass pressure is factory set –

adjustments may damage unit!

Electrical Precautions

1. Make certain that the power source conforms to the requirements of

the equipment.

2. Keep all connections dry and off the ground. Do not handle the unit or electrical

plug with wet hands.

3. Unplug the power cord when servicing the unit or leaving the machine unattended.

4. Do not pull on the power cord or pull the cord around sharp corners. Keep the cord

away from hot surfaces. When unplugging the power cord, grasp the plug – not

the cord.

5WARNING: The cords, wires, and/or cables supplied with this product may contain

chemicals, including lead or lead compounds, known to the State of California to

cause cancer and birth defects or other reproductive harm. Always wash hands

thoroughly after handling the unit.

6. GROUNDING INSTRUCTIONS: For proper protection this product must be

grounded. Always plug the power cord into a properly grounded receptacle. Never

remove the grounding prong from the power cord plug or use an adapter that

eliminates ground.

7. GROUND FAULT CIRCUIT INTERRUPTER: This unit is provided with a Ground

Fault Circuit Interrupter built into the power cord plug to prevent electrocution. DO

NOT RUN THE UNIT WITHOUT THIS DEVICE!! If replacement of the plug or cord

becomes necessary, use only identical replacement parts that include

GFCI protection.

8. EXTENSION CORDS: Use only extension cords that are intended for outdoor

use. These extension cords are identied by a marking “Acceptable for use with

outdoor appliances; store indoors while not in use.” Use only extension cords having

an electrical rating not less than the rating of the product. Do not use damaged

extension cords. Examine extension cord before using and replace if damaged. Do

not abuse extension cord and do not yank on any cord to disconnect. Keep cord

away from heat and sharp edges. Always disconnect the extension cord from the

receptacle before disconnecting the product from the extension cord.

SAVE THESE INSTRUCTIONS

CC-400HF HI-FLO 0121 5

Operating Instructions

1. Unwrap hose from unit. Attach to quick connect on output of pump.

2. Attach Spray Gun to quick connect on hose (attach Extension Lance if necessary).

3. Unwrap power cord from unit. Plug into outlet. Test and reset GFCI.

4. Attach water supply hose to unit (3 gallons per minute minimum). Make sure screen

washer is in place.

5. Turn on water. To prime the pump, squeeze the Spray Gun trigger until water exits.

6. Remove the red oil cup from the pump and replace it with the black cup in the

supplied plastic bag.

Normal Coil Cleaning:

1. Attach Yellow Rinsing Nozzle (size 1510) to Spray Gun (or Extension Lance,

if attached).

2. While holding Spray Gun trigger open, ip power switch (on rear of unit) to

“ON” position.

3. Spray condenser with plenty water to remove loose debris.

4. Remove Yellow Rinsing Nozzle from Spray Gun/Lance.

5. Attach Soap Nozzle (Stainless Steel, size 1520).

6. Make sure chemical pickup hose is in chemical container and the tip is at the bottom.

7. Apply water/chemical solution evenly to coils (siphon ratio is approximately 10:1).

8. If possible, let coil cleaner chemical sit for 5 minutes to penetrate into coils and

loosen deposits.

9. Remove Soap Nozzle, attach Yellow Rinsing Nozzle, and thoroughly rinse coils with

clean water.

10. When done, ip Power Switch to the “OFF” position and relieve pressure in hose.

Using the Wonder Wand™

1. Insert the Wonder Wand™ into the top of a condenser unit to clean coils from inside

to outside (removing debris in the opposite direction of the airow) without taking

fan and cover off of the condenser.

2. The Hi-Flo Coil Cleaner will siphon draw chemical at approximately 10:1.

3. To rinse coils with clean water using the wand attachments, remove chemical pickup

hose from chemical.

CC-400HF HI-FLO 0121

General Maintenance and Storage

1. If using with cleaning chemicals, run clean water through the pump

when done.

2. Periodically check oil level in pump sight glass. Use only approved oil to top off

if below dot in sight glass.

3. IMPORTANT!! Replace water seals immediately if pump leaks between head

and crankcase.

4. Store unit indoors.

ACCESSORIES/SPARE PARTS

SPECIFICATIONS

TROUBLESHOOTING

Accessory/Spare Part Part #

15° Rinsing Nozzle (Yellow) QDN-1510Y

20° Soap Nozzle QDN-LP25

18” Extension Lance 9655

Spray Gun Assembly RCC-14

Hose Assembly (12 ft) RCC-13

35” Wonder Wand - Sectional Two

Piece (Included)

WWSS-HF

Replacement Water Seal Kit for Pump RCC-10-SK

90° Brass Tip WWSS-60-90DEG

Motor/ Power Requirements 1 HP AC Motor (1φ) / 115 VAC / 15.0 Amps

Water Requirements 3.0 GPM (11.4LPM)

Maximum Inlet Water Pressure 100 PSI (7 BAR)

Maximum Outlet Water Pressure 400 PSI (28 BAR)

Weight 45 lbs (20.4 kg)

Maximum Inlet Water Temperature 125°F (52°C)

Maximum Ambient Operational

Temperature

104°F (40°C)

PROBLEM PROBABLE CAUSE REMEDY

Inconsistent and/or

erratic pressure

• Nozzle clogged

• Inadequate water supply

• Clean nozzle orice

• 3.0 GPM minimum

Motor stops abruptly • Motor Thermal breaker

tripped

• Turn off, let unit cool

Motor buzzes but fails to

start

• Inadequate Power

Supply

• Check for 115VAC/15

A min

Unit does not spray

chemical

• Wrong Nozzle Attached

• Pickup hose not in

chemical

• Attach Soap Nozzle

(size 1520)

• Put hose to bottom

of chemical

CC-400HF HI-FLO 0121 7

Exploded View

1039

HWS-2520-125P

X2-05-04

RCC-01-G

RCC-06-1

X2-05-03

2509

RCC-15-1

808

842

RCC-02-G

RCC-04

684

9008

RCC-12RCC-19

RCC-16-2

HWN-252

802

RCC-07-1

BSL-45EL50FX50M

9527

RCC-10

HWN-37L

RCC-16

935

2 ft

RCC-18

X2-05-03

2509

HWN-252

HWS-2520-125P

RCC-18

RCC-10-2

RCC-15-2

X2-05-03

684

9008

HWS-1037

RCC-10-SK

RCC-03-G

CC-400HF HI-FLO 0121

Part Number Description QTY.

RCC-15-1 Switch, 1.5 hp Max 1

684 Screw, 1/4-20 panhead, 3/4" L 4

802 HOSE CONNECTOR 1

808 Romex Fitting 1

842 GFCI, 115V 1

935 Hose, Braided, 1/4' ID 2

1039 Tip, For Siphon Hose 1

2509 Grommet, 1/2 ID 4

9008 Foot 4

9527 Quick Connect, Female, 3/8 1

BSL-45EL50FX50M Brass Elbow, 45 degree, 1/2M x F 1

HWN-37L Nut, Nylock, 3/8 4

HWN-252 Nut, 1/4-20 4

HWS-1037 Screw, #10, Sheet Metal, 3/8" 2

HWS-2520-125P Screw, 1/4-20, Panhead, 1.25 8

HWW-252 Washer, 1/4 4

RCC-01-G Mounting Plate, Molded, Front 1

RCC-02-G Mounting Plate, Molded, Rear 1

RCC-03-G Cover Tube 1

RCC-04 Bafe, Rear 1

RCC-06-1 Tube, 3/4 OD, 9.56 L 3

RCC-07-1 Pump Guard 1

RCC-10 Pump, 3.0 GPM 1

RCC-10-2 Thermal Relief Valve, 1/4 NPT 1

RCC-10-SK Seal Kit, RCC-10 1

RCC-12 Motor, 1 HP, 56F 1

RCC-15-2 Cover, for 530-117 Switch 1

RCC-16 Heat Shield, Complete Set 1

RCC-16-2 Heat Shield, Washer, Motor 4

RCC-17-2 Heat Shield, Washer, Pump 4

RCC-18 Grommet, 3/8 ID 6

RCC-19 Motor Set Screw, 3/8-16, 2.25'"L 4

X2-05-03 Star Nut, Tube Connector 8

X2-05-04 Foam Grip, 1/2 ID. 5.25 1

CC-400HF HI-FLO 0121 9

ON/ OFF

Switch

DO NOT LAY UNIT

DOWN ON THIS END

DO NOT LIFT OR

CARRY BY PUMP

GUARD!!!

Lift by handle

only

Hoist

point

Hoist

point

Thermal Relief

Valve

Chemical Hose

CC-400HF HI-FLO 0121

NOTES

Andere Handbücher für Hi-Flo CC-400HF

Inhaltsverzeichnis

Andere Good Way Reinigungsgeräte Handbücher

Good Way

Good Way VAC-EX-120-9-SS Bedienungsanleitung

Good Way

Good Way TFC-JR Betriebsanleitung

Good Way

Good Way SOOT-A-MATIC SAM-3 Installations- und Betriebshandbuch

Good Way

Good Way 93-ACC-BRUSHLESS Handbuch

Good Way

Good Way Hi-Flo CC-400HF Bedienungsanleitung

Good Way

Good Way REAM-A-MATIC RAM-5 GT Handbuch

Good Way

Good Way GDS-C40 Handbuch

Good Way

Good Way GVC-BP-1700 Handbuch

Good Way

Good Way QUICK SHOT QS-300 Handbuch

Good Way

Good Way Ream-A-Matic Handbuch

Good Way

Good Way BioSpray-5 Handbuch

Good Way

Good Way GDS-15-PH Handbuch

Good Way

Good Way GVC-18000 Handbuch

Good Way

Good Way CoilVac CVC-100 Handbuch

Good Way

Good Way BioSpray-10C Handbuch

Beliebte Reinigungsgeräte Handbücher anderer Marken

Skov

Skov Farm AirClean Handbuch

Nilfisk-Advance

Nilfisk-Advance CA 240 Bedienungsanleitung

ORBOT

ORBOT LiO Bedienungsanleitung

unGer

unGer OmniClean Bedienungsanleitung

CENTREGO

CENTREGO Toucan Eco Bio Carry Bedienungsanleitung

BANDELIN

BANDELIN SONOREX TECHNIK RM 110 UH Bedienungsanleitung

Sealey

Sealey VMA913 Bedienungsanleitung

Aztec

Aztec 520-00 Bedienungsanleitung

BÖWE

BÖWE P25 Bedienungsanleitung

Tunap

Tunap MF 929 Bedienungs- und Montageanleitung

RIDGID

RIDGID K-45AF-7 Bedienungsanleitung

Aircraft

Aircraft POWERGLIDE Bedienungsanleitung

Suevia

Suevia 130.5011 EASYCLEANER Bedienungsanleitung

Streamline

Streamline Filterplus MOBI SK Bedienungsanleitung

Thermax

Thermax AF2 Bedienungsanleitung

IPC

IPC CT15R Bedienungsanleitung

i-MO

i-MO Öko 2000 Bedienungsanleitung

unGer

unGer Hydro Power Ultra UNP01 Bedienungsanleitung