Goodman HAMFK Bedienungsanleitung

APPLICATION

This kit is to be used for high altitude conversion of modu-

lating gas furnaces equipped with WHITE-RODGERS 36J27

SERIES GAS VALVES ONLY (Figure 1). This kit also contains

parts and instructions for conversion to L.P. This kit is not

applicable in Canada. Parts apply as shown in the table be-

low.

Natural Gas

Orifices Propane Gas

Orifices

B2589907 (#49) B2589908 (#56)

Above 7,000 Feet

Table 1

HAMFK - HIGH ALTITUDE CONVERSION KIT FOR

34"MODULATING FURNACE

FURNACES EQUIPPED WITH WHITE-RODGERS 36J27 SERIES GAS VALVES

DONOTDISCARD-RETAINTHESEINSTRUCTIONSFORFUTUREUSE.

Goodman Manufacturing Company, L.P.

5151 San Felipe, Suite 500 • Houston, TX 77056

isaregistered trademark of Maytag Corporation or its related companies and isused under license

IOG-7005

December 2018

Figure 1 - 36J27 Modulating Gas Valve

Q'ty Description

1 Needle-Nose Pliers

17/16"BoxWrench

11/4"NutDriver

1 1/8" Flat Blade Screwdriver

1Manometer to read inlet and outlet pressure of the

gas valve (minimum range: 0"- 20" W.C.)

Gas leak detection solution like a soap and water

solution. Always wipe the solution from the joints

when testing is completed.

Required Tools for Conversion Kit

Only personnel that have been trained to install, adjust, service

or repair (hereinafter, “service”) the equipment specified in

this manual should service the equipment. The manufacturer

will not be responsible for any injury or property damage

arising from improper service or service procedures. If you

service this unit, you assume responsibility for any injury or

property damage which may result. In addition, in jurisdictions

that require one or more licenses to service the equipment

specified in this manual, only licensed personnel should service

the equipment. Improper installation, adjustment, servicing

or repair of the equipment specified in this manual, or

attempting to install, adjust, service or repair the equipment

specified in this manual without proper training may result in

product damage, property damage, personal injury or death.

Cancer and Reproductive Harm -

www.P65Warnings.ca.gov

PROP 65 WARNING

FOR CALIFORNIA CONSUMERS

0140M00513-A

HIGHALTITUDE CONVERSION

1. Shut OFF gas supply at manual shutoff and turn OFF power to the furnace.

2. Remove access door.

3. Disconnect wiring from the gas valve.

4. Remove the gas manifold assembly by removing the four screws connecting it to the burner bracket. See Figure 2 below.

Figure 2 - Gas Manifold Removal

5. Remove factory installed orifices from gas manifold using 7/16" box end wrench.

For Natural Gas Operation, complete steps 6 & 7; For L.P. Gas Operation, complete steps 8 through 13.

6. Visually inspect the high altitude Natural Gas orifices (B2589907) for damage and drill size (#49) before installation.

Install orifices and tighten with a box-end wrench, take care to avoid cross threading or over tightening.

7. Attach the gas manifold assembly to the burner bracket using the four screws removed in step 4.

8. Visually inspect the high altitude L.P. Gas orifices (B2589908) for damage and drill size (#56) before installation. Install

orifices and tighten with a box-end wrench, take care to avoid cross threading or over tightening.

9. Remove the “NAT. GAS” label from the top of the 36J27 gas valve.

10. Use needle nose pliers to place the jumper (see enclosed F92-1021 kit) on the receptacle. Make sure both pins engage the

jumper.

11. Place the “L.P.” label (see the enclosed F92-1021 kit) on the gas valve, covering the jumper installed in step 8.

12. Attach the “WARNING” label (see the enclosed F92-1021 kit) to the gas valve where it can be readily be seen.

13. Attach the gas manifold assembly to the burner bracket using the four screws removed in step 4.

GAS SUPPLY PRESSURE CHECK

Gas Supply Pressure must be verified with all appliances in operating mode. See Table 2 for the required gas pressure.

1. Turn OFF electrical power & gas supply to the unit.

2. Use 3/16"Allen wrench to remove 1/8" inlet pressure tap from the gas valve.

3. Connect a calibrated water manometer or appropriate gas pressure gauge at the gas valve inlet pressure tap.

4. Turn ON the power and gas, put the unit into heating cycle on high fire (100%) to verify proper supply pressure. If gas

supply is not within the range specified, contact your gas provider.

Manifold

Gas Valve

4 Screws

5. Turn OFF gas to the unit at the manual shutoff valve and disconnect manometer. Reinstall line pressure tap plug. The

pressure tap must be leak checked after resealing.

GAS TYPE MIN MAX

NATURAL 5" w.c. 10" w.c.

L.P. 11" w.c. 13" w.c.

GAS SUPPLY PRESSURE RANGE

Table 2

MANIFOLDPRESSURECHECK

Refer to table 3 for proper Natural Gas manifold pressure & table 4 for proper L.P. Gas manifold pressure. *For L.P. Gas, the

gas valve outlet pressure is automatically adjusted for LP by installation of the jumper in step 10. Only minor changes to

manifold pressure should be made by adjusting the gas valve pressure regulator. Minor adjustments may be made by

removing the access plug and turning the fine-adjustment screw with 1/8" flat blade screwdriver. Adjustment should only be

done with monitoring outlet pressure with a suitable manometer properly attached to the outlet pressure tap.

1. Turn OFF electrical power &gas supply to the unit.

2. Use a 3/16"Allen wrench to remove 1/8" outlet pressure tap from the gas valve.

3. Connect a calibrated water manometer or appropriate gas pressure gauge at the gas valve outlet pressure tap.

4. Turn ON the power and gas, put the unit into heating cycle on high fire (100%).

5. Remove the White cap located on top the gas valve next to the + &- symbols.

6. Use a 1/8" flat blade screwdriver to turn the fine adjustment screw, clockwise (+) to increase manifold pressure, counter

clockwise (-) to decrease manifold pressure.

7. After adjustment is made, turn OFF gas to the unit at the manual shutoff valve and disconnect manometer. Reinstall line

pressure tap plug. The pressure tap must be leak checked after resealing.

Natural Gas Manifold Pressure Range

Low Stage High Stage

.85" w.c. - 1" w.c. 3.2" w.c. - 3.8" w.c.

Table 3

Low Stage High Stage

2.3" to 2.7" w.c. 9.7" to 10.3" w.c.

Propane Gas Manifold Pressure Range

Table 4

CUSTOMER FEEDBACK

We are very interested in all product comments.

Please fill out the feedback form on one of the following links:

Goodman®BrandProducts:(http://www.goodmanmfg.com/about/contact-us).

Amana® Brand Products: (http://www.amana-hac.com/about-us/contact-us).

You can also scan the QR code on the right for the product brand

you purchased to be directed to the feedback page.

GOODMAN® BRAND AMANA® BRAND

NOTE: SPECIFICATIONSANDPERFORMANCEDATALISTED HEREINARESUBJECTTOCHANGEWITHOUTNOTICE

• Products

• Warranties

• Customer Services

Quality Makes the Difference!

All of our systems are designed and manufactured with the same high quality standards regardless of size or effi-

ciency. We have designed these units to significantly reduce the most frequent causes of product failure. They are

simple to service and forgiving to operate. We use quality materials and components. Finally, every unit is run tested

before it leaves the factory. That’s why we know. . .There’s No Better Quality.

Visit our website at www.goodmanmfg.com or www.amana-hac.com for information on:

• Parts

• Contractor Programs and Training

• Financing Options

Inhaltsverzeichnis

Andere Goodman Ofen Handbücher

Goodman

Goodman GMV950453BX Series Technisches Dokument

Goodman

Goodman CVM96 Series Bedienungsanleitung

Goodman

Goodman MH8 Bedienungsanleitung

Goodman

Goodman GDH8 Bedienungsanleitung

Goodman

Goodman GMVC950453BXAA Bedienungsanleitung

Goodman

Goodman GME80603B Series Bedienungsanleitung

Goodman

Goodman GMS8 Handbuch

Goodman

Goodman GME95 Bedienungsanleitung

Goodman

Goodman *MEC96 Bedienungsanleitung

Goodman

Goodman MVC8 Bedienungsanleitung

Goodman

Goodman GMV9 Bedienungsanleitung

Goodman

Goodman GMEC96 Betriebsanleitung

Goodman

Goodman GMPN Handbuch

Goodman

Goodman GMSS96 Bedienungsanleitung

Goodman

Goodman GMEC80 Bedienungsanleitung

Goodman

Goodman GCVM960604CXA Series Bedienungsanleitung

Goodman

Goodman GDS8 Bedienungsanleitung

Goodman

Goodman MVM96 Series Bedienungsanleitung

Goodman

Goodman GDVC80703B Bedienungsanleitung

Goodman

Goodman GMS80453ANCC Gebrauchs- und Pflegehandbuch

Goodman

Goodman MVM96 Series Bedienungsanleitung

Goodman

Goodman *MEC96 Bedienungsanleitung

Goodman

Goodman ComfortNet ACVC90704CXAA Gebrauchs- und Pflegehandbuch

Goodman

Goodman [A/G]PG Betriebsanleitung

Beliebte Ofen Handbücher anderer Marken

Armstrong

Armstrong EG7H SERIES Bedienungsanleitung

Payne

Payne PG92ESA Leitfaden

SUPREME

SUPREME FEM10-M2301CM-A Montageanleitung

Ingersoll-Rand

Ingersoll-Rand S9V2B080D4VSAC/D Montageanleitung

Johnson Controls

Johnson Controls TM9T Leitfaden

Fluke

Fluke 9118A Bedienungsanleitung

Lennox

Lennox EL195UHE Elite Series Installations- und Betriebshandbuch

Intertherm

Intertherm M7RL Series Bedienungsanleitung

HDG

HDG Pelletmaster 15 Bedienungsanleitung

Pinnacle

Pinnacle Aero Bella AB-716C-QH Handbuch

Nortek

Nortek MG2S Series Bedienungsanleitung

VERDER

VERDER CARBOLITE GERO ABF 8/28 Handbuch

SUPREME

SUPREME SUP10-M2301C Montageanleitung

Dettson

Dettson AMT400B34-SM1PMA Montageanleitung

Evcon

Evcon DGD 60 MBH Bedienungsanleitung

Trane

Trane S8B1A026M2PSAB Montageanleitung

Hart Sceintific

Hart Sceintific 9113 Bedienungsanleitung

Whirlpool

Whirlpool Gold WGGE45 Bedienungsanleitung