Goodman GPH 14 SEER R-410A Bedienungsanleitung

•RefertoServiceManualRS6300011(Horizontal)

forinstallation,operation,and troubleshooting information.

•Allsafety information mustbe followed asprovided in the Service Manual.

•Refertothe appropriate Parts Catalogfor part number information.

•Models listed on page 3.

•Modelsqualify for the2009 and 2010Federal Tax Creditsfor Energy Efficiency**

TECHNICAL MANUTECHNICAL MANU

TECHNICAL MANUALAL

ALAL

GPH 14 SEER R-410A

Package Heat Pump Units

RT6332012r2

September2010

**Note that these tax credits are subject to specific requirements set forth in the American Recovery and

Reinvestment Act of 2009 and in the Internal Revenue Code. Goodman recommends that consumers

consult a tax professional if they have questions about the applicability of these credits.

This manual is to be used by qualified, professionally trained HVAC technicians only. Goodman does not

assume any responsibility for property damage or personal injury due to improper service procedures or

services performed by an unqualified person.

PRODUCT IDENTIFICATION

Themodelandmanufacturingnumberareusedfor positive identification of component partsusedinmanufacturing. Please

usethesenumbers when requestingservice or partsinformation.

WARNING

WARNING HIGH VOLTAGE!

Disconnect ALL power before servicing or installing this unit. Multiple power

sources may be present. Failure to do so may cause property damage, personal

injury or death.

Installation and repair of this unit

should be performed ONLY by

individuals meeting (at a minimum) the requirements of

an "entry level technician" as specified by the Air-Condi-

tioning, Heating, and Refrigeration Institute (AHRI). At-

tempting to install or repair this unit without such back-

ground may result in product damage, personal injury or

death.

Goodman will not be responsible

for any injury or property damage

arising from improper service or service procedures. If

you install or perform service on this unit, you assume

responsibility for any personal injury or property damage

which may result. Many jurisdictions require a license to

install or service heating and air conditioning equipment.

WARNING

WARNING WARNING

WARNING

GPH1424H41AA

PRODUCT

TYPE:

Package Unit

PRODUCT

FAMILY:

H:Heat Pump

PRODUCT

SERIES:

SEER Rating

BRAND:

G:Goodman®

Brand

OMINAL

APACITY

4: 24,000 BTUH

0: 30,000 BTUH

6: 36,000 BTUH

2: 42,000 BTUH

8: 48,000 BTUH

0: 60,000 BTUH

CONFIGURATION:

H: Horizontal

REFRIGERANT:

4: R-410A

VOLTAGE:

1: 208-230v

1ph/60Hz

MAJOR REVISION:

: Initial Release

MINOR REVISION:

: Initial Release

PRODUCT IDENTIFICATION

GPH1424H41AB

GPH1430H41AB

GPH1436H41AB

GPH1442H41AB

GPH1448H41AB

GPH1460H41AB

Themodelandmanufacturingnumberareused for positive identification of componentpartsusedinmanufacturing. Please

usethesenumbers when requestingservice or partsinformation.

The United States Environmental Protection Agency (“EPA”) has issued various regulations re-

garding the introduction and disposal of refrigerants introduced into this unit. Failure to follow

these regulations may harm the environment and can lead to the imposition of substantial fines.

These regulations may vary by jurisdiction. Should questions arise, contact your local EPA office.

WARNING

Do not connect or use any device

that is not design certified by

Goodman for use with this unit.

Serious property damage, personal injury, reduced unit

performance and/or hazardous conditions may result

from the use of such non-approved devices.

WARNING

WARNING To prevent the risk of property

damage, personal injury, or death,

do not store combustible materials or use gasoline or

other flammable liquids or vapors in the vicinity of this

appliance.

WARNING

Modelsqualify for the 2009and 2010 FederalTax Credits

forEnergy Efficiency**

**Note that these tax credits are subject to specific requirements set forth in the American

Recovery and Reinvestment Act of 2009 and in the Internal Revenue Code. Goodman

recommends that consumers consult a tax professional if they have questions about the

applicability of these credits.

PRODUCT DESIGN

GPH Package Units are designed for outdoor installations

only in either residential or light commercial applications.

The connecting ductwork (Supply and Return) can only be

connectedforhorizontalairflow.

Areturnairfiltermustbeinstalledbehind thereturnairgrille(s)

or provision must be made for a filter in an accessible loca-

tionwithinthereturn air duct. Theminimumfilterarea should

not be less than those sizes listed in the Specification Sec-

tion. Under no circumstances should the unit be operated

withoutreturn air filters.

A3/4"pipeis provided for removalofcondensate water from

theindoorcoil. In orderto provide proper condensateflow, a

drain trap is supplied and shipped loose inside the unit for

field installation. (Do not reduce the drain line size).

Refrigerant flow control is achieved by use of restrictor ori-

fices.

PackageHeat Pump modelsuse a combination of restrictor

orificesandthermostaticexpansion valves forrefrigerantflow

control.

Someheatpumpmodels also haveasuction line accumula-

torinstalledbetween thereversingvalveandthecompressor.

The object of the accumulator is to:

1. Providealiquidrefrigerantstoragevesselduringprolonged

system off cycles.

2. Storeexcessliquid refrigerant notneededby the system

whilerunning.

3. Return oil and saturated vapor to the compressor at a

controlledrate.

4. Retainstoredexcessrefrigerantduring a sudden system

pressure fluctuation such as seen in defrost cycles.

Refrigerant flow control is achieved by use of restrictor ori-

fices. GPH units use the FasTest Access Fitting System,

witha saddle that is either soldered to the suction and liquid

lines or is fastened with a locking nut to the access fitting

box (core) and then screwed into the saddle. NOTE: The

core must not be removed from the saddle until the

refrigerant charge has been removed. Failure to do so

could result in property damage or personal injury.

Thesingle phase unitsuse permanent split capacitor (PSC)

design compressors. Starting components are not required

for these units. A low microfarad run capacitor assists the

compressor to start and remains in the circuit during opera-

tion.

GPH14[24-60]H41*unitshaveX-13indoorblowermotorsthat

areenergizedbya 24V signalfromtheIBR and areconstant

torque motors with very low power consumption. The X-13

featuresanintegral control module.

Air for condensing (cooling cycle) or evaporation (heating

cycle) is drawn through the outdoor coil by a propeller fan,

and is discharged vertically out the top of the unit. The out-

door coil is designed for .0 static. No additional restriction

(ductwork)shallbe applied.

Conditioned air is drawn through the filter(s), field installed,

across the coil and back into the conditioned space by the

indoorblower.

PackageHeatPump indoor sections aredesigned to accept

optional components such as auxiliary electric heaters and

circuitbreakers.Provisionsforthesecomponentshavebeen

madeat time ofmanufacture.

LocationandClearances

NOTE:Toensurepropercondensatedrainage, unit must be

installed in a level position.

Outside Slab Installation - Horizontal (H)

NOTE:Roof overhangshouldbenomorethan36"andprovi-

sions made to deflect the warm discharge air out from the

overhang.

Minimum clearances are required to avoid air recirculation

and keep the unit operating at peak efficiency.

PRODUCT DESIGN

36"

24"

PLENUM

UNIT

PLATFORM

CURB

Rooftop Installation - Horizontal (H)

NOTE:Toensurepropercondensatedrainage, unit must be

installed in a level position.

Ininstallationswhere the unitis installed aboveground level

and not serviceable from the ground (Example: roof top in-

stallations)theinstallermustprovideserviceplatformforser-

vicepersonwithrailsorguardsinaccordancewithlocalcodes

or ordinances, or, in their absence, with the latest edition of

theUniform Mechanical CodeSection 305.

WARNING

TO PREVENT POSSIBLE PROPERTY DAMAGE, THE

UNIT SHOULD REMAIN IN AN UPRIGHT POSITION

DURING ALL RIGGING AND MOVING OPERATIONS.

TOFACILITATELIFTINGANDMOVINGIFACRANEIS

USED, PLACE THE UNIT IN AN ADEQUATE CABLE

SLING.

Refer to Roof curb Installation Instructions for proper curb

installation.Curbingmustbe installed in compliancewiththe

NationalRoofingContractors Association Manual.

PRODUCT DESIGN

HKR ELECTRICAL DATA

All wires and overcurrent protection devices are sized for use with electric heaters only and without

refrigeration. If heaters are not installed with above wire size, overheating and fire could occur. See

PACKAGE COOLING SPECIFICATIONS section for minimum circuit ampacity and maximum overcurrent

protection during refrigeration cycle.

IMPORTANT NOTE: A separate power supply is required for the HKR heater kit.

WARNING

GPH14[24-60]H41A*

Maximum Maximum

Overcurrent Overcurrent

Protection (amps) Protection (amps)

at 208 / 240V at 208 / 240V

GPH1424H41A*

HKR05*,C* 24 / 27 30 / 30 ---- ---- 4.75 /16,200

HKR08*,C* 33 / 28 40 / 40 ---- ---- 7.00 /23,800

HKR10*,C* 45 / 51 60 / 60 ---- ---- 9.50 / 32,400

GPH1430H41A*

HKR05*,C* 24 / 27 30 / 30 ---- ---- 4.75 /16,200

HKR08*,C* 34 / 39 40 / 40 ---- ---- 7.00 /23,800

HKR10*,C* 45 / 52 60 / 60 ---- ---- 9.50 /32,400

HKR15*,C* 45 / 52 60 / 60 22 / 25 30 / 30 14.25 / 48,600

GPH1436H41A*

HKR05*,C* 24 / 27 30 / 30 ---- ---- 4.75 /16,200

HKR08*,C* 34 / 39 40 / 40 ---- ---- 7.00 /23,800

HKR10*,C* 45 / 52 60 / 60 ---- ---- 9.50 /32,400

HKR15*,C* 45 / 52 60 / 60 22 / 25 30 / 30 14.25 / 48,600

GPH1442H41A*

HKR05*,C* 25 / 27 30 / 30 ---- ---- 4.75 /16,200

HKR08*,C* 34 / 39 40 / 40 ---- ---- 7.00 /23,800

HKR10*,C* 46 / 52 60 / 60 ---- ---- 9.50 /32,400

HKR15*,C* 46 / 52 60 /60 22 / 25 30 /30 14.25 / 48,600

HKR20*,C* 46 / 52 60 / 60 43 / 49 60 / 60 19.50 / 66,500

GPH1448H41A*

HKR05*,C* 25 / 28 30 / 30 ---- ---- 4.75 /16,200

HKR08*,C* 34 / 40 40 / 40 ---- ---- 7.00 /23,800

HKR10*,C* 46 / 53 60 / 60 ---- ---- 9.50 /32,400

HKR15*,C* 46 / 52 60 /60 22 / 25 30 /30 14.25 / 48,600

HKR20*,C* 46 / 52 60 /60 43 / 49 60 /60 19.50 / 66,500

GPH1460H41A*

HKR05*,C* 26 / 30 30 / 30 ---- ---- 4.75 /16,200

HKR08*,C* 36 / 40 40 / 40 ---- ---- 7.00 /23,800

HKR10*,C* 48 / 54 60 / 60 ---- ---- 9.50 /32,400

HKR15*,C* 48 / 54 60 /60 22 / 25 30 /30 14.25 / 48,600

HKR20*,C* 48 / 54 60 / 60 43 / 49 60 / 60 19.50 / 66,500

Actual

kW & BTU

at 240V

Minimum Circuit

Ampacity

at 208 / 240V

Minimum Circuit

Ampacity

at 208 / 240V

Model and Heat Kit Usage

Circuit #1 Circuit #2

PRODUCT DIMENSIONS

34.075

66.542

4.512

14.000

SUPPLY 6.500 RETURN

4.500

BACK VIEW

(DUCT OPENINGS)

14.000

GPH14[24-60]H41A*

Chassis Model A B

GPH1424H41** 22.000 29.932

GPH1430H41** 22.000 29.932

GPH1436H41** 24.000 34.932

GPH1442H41** 24.000 34.932

GPH1448H41** 24.000 38.682

GPH1460H41** 24.000 38.682

Small

Medium

Large

PACKAGE HEAT PUMP SPECIFICATIONS

GPH14[24-36]H41AB

(2) Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.

*Calculated external filter size based on air velocity of 300 ft/min.

Wire size should be determined in accordance with National Electrical Codes. Extensive wire runs will require larger wire sizes.

Unit specifications are subject to change without notice. ALWAYS refer to the units serial plate for the most up-to-date general and electrical information.

IMPORTANT: While this data is presented as a guide, it is important to electrically connect the unit and properly size wires and fuses/circuit breakers

in accordance with the National Electrical Code and/or all local codes. Data shown is w/o electric heaters.

GPH1424H41** GPH1430H41** GPH1436H41**

COOLING COOLING CAPACITY,BTUH 24,400 29,600 36,000

CAPACITY SEER / EER 15.0 / 12.2 14.5 / 12.2 14.3 / 12.0

HEATING 47°/43°F 22,800 27,600 33,000

RATING 35°/33°F 15,500 18,600 26,000

17°/15°F 13,000 15,400 21,400

HSPF 8.0 8.3 8.5

UNIT VOLTAGE (NAMEPLATE) 208/230-60-1 208/230-60-1 208/230-60-1

ELECTRICAL AMPS 15.4 17.1 20.1

SPECIFICATION MIN CIRCUITAMPACITY 12.5 15.6 24.2

MAX OVERCURRENT PROTECTION(2) 20 25 40

COMPRESSOR TYPE SCROLL SCROLL SCROLL

RATED LOAD AMPS 12.8 14.1 16.7

LOCKED ROTOR AMPS 58.3 73 79

CONDENSER HORSEPOWER 1/6 1/6 1/4

FAN MOTOR RPM 815 815 1075

FULL LOAD AMPS 1.1 1.1 1.5

LOCKED ROTOR AMPS 1.7 1.7 3.0

CONDENSER FAN BLADE DIAMETER (INCHES) / # OF BLADES 22 / 3 22 / 3 22 / 4

CONDENSER FACE AREA (SQ. FT.) 13.4 13.4 17

COIL NUMBER OF ROWS 1 1 1

FINS PER INCH 24 24 24

EVAPORATOR HORSEPOWER - NO. OF SPEEDS 1/2 - 5 1/2 - 5 1/2 - 5

BLOWER FULL LOAD AMPS 1.50 1.86 1.86

MOTOR LOCKED ROTOR AMPS NA NA NA

MOTOR SPEED TAP - COOLING T2 T2 T2

RPM 1,050 1,050 1,050

EVAPORATOR DIAMETER X WIDTH (INCHES) 10 X 8 10 X 8 10 X 8

BLOWER RATED SCFM COOLING 850 1,050 1,200

HI EFFICIENCY COOLING CFM 850 1,050 1,200

FAN ONLYCOOLING CFM 800 950 1,100

MAX EXTERNAL STATIC PRESS ("w.c.) 0.5 0.5 0.5

EVAPORATOR FACE AREA (SQ. FT.) 5.25 4.67 5.20

COIL NUMBER OF ROWS 3 4 3

FINS PER INCH 16 16 14

GENERAL FILTER SIZE (SQ. FT.) 20 x 20 x 1 20 x 25 x 1 25 x 25 x 1

INFORMATION DRAIN SIZE (INCHES) 3/4" 3/4" 3/4"

EXPANSION DEVICE (INDOOR / OUTDOOR) ORIFICE (0.057 / 0.049) ORIFICE (0.065 / 0.047) ORIFICE (0.068 / 0.067)

REFRIGERANTCHARGE R-410A (OZS.) 85 105 125

POWER SUPPLY CONDUIT KNOCKOUT SIZE (") 3/4, 1, 1-1/4 3/4, 1, 1-1/4 3/4, 1, 1-1/4

LOW VOLTAGE CONDUIT KNOCKOUT SIZE (") 1/2 1/2 1/2

LO PRESSURE SWITCH

OPENS / CLOSES PSIG 22 / 50 22 / 50 22 / 50

HI PRESSURE SWITCH - OPENS PSIG

OPENS / CLOSES PSIG 660 / 420 660 / 420 660 / 420

SHIPPING WEIGHT (LBS.) 325 325 385

OPERATING WEIGHT (LBS.) 315 315 375

PACKAGE HEAT PUMP SPECIFICATIONS

GPH14[42-60]H41AB

(2) Maximum Overcurrent Protection Device: MUST use Time Delay Fuse or HACR type Circuit Breaker of the same size as noted.

*Calculated external filter size based on air velocity of 300 ft/min.

Wire size should be determined in accordance with National Electrical Codes. Extensive wire runs will require larger wire sizes.

Unit specifications are subject to change without notice. ALWAYS refer to the units serial plate for the most up-to-date general and electrical information.

IMPORTANT: While this data is presented as a guide, it is important to electrically connect the unit and properly size wires and fuses/circuit breakers

in accordance with the National Electrical Code and/or all local codes. Data shown is w/o electric heaters.

GPH1442H41** GPH1448H41** GPH1460H41**

COOLING COOLING CAPACITY, BTUH 40,000 46,000 57,000

CAPACITY SEER / EER 14.2 / 12.0 14.5 / 12.1 14.2 / 12.0

HEATING 47°/43°F 37,600 45,000 54,500

RATING 35°/33°F 27,500 32,000 43,000

17°/15°F 21,600 26,000 33,800

HSPF 8.3 8.3 8.4

UNIT VOLTAGE (NAMEPLATE) 208/230-60-1 208/230-60-1 208/230-60-1

ELECTRICAL AMPS 22.2 24.2 30.7

SPECIFICATION MIN CIRCUIT AMPACITY 26.6 29.2 40.2

MAX OVERCURRENT PROTECTION(2) 40 45 60

COMPRESSOR TYPE SCROLL SCROLL SCROLL

RATED LOAD AMPS 17.9 19.9 26.4

LOCKED ROTOR AMPS 112 109 134

CONDENSER HORSEPOWER 1/4 1/4 1/4

FAN MOTOR RPM 1075 1075 1075

FULL LOAD AMPS 1.4 1.4 1.4

LOCKED ROTOR AMPS 2.9 2.9 2.9

CONDENSER FAN BLADE DIAMETER (INCHES) / # OF BLADES 22 / 4 22 / 4 22 / 4

CONDENSER FACE AREA (SQ. FT.) 17 19.1 19.1

COIL NUMBER OF ROWS 1 2 2

FINS PER INCH 24 16 16

EVAPORATOR HORSEPOWER - NO. OF SPEEDS 1/2 - 5 3/4 - 5 3/4 -5

BLOWER FULL LOAD AMPS 2.9 2.9 2.9

MOTOR LOCKED ROTOR AMPS NA NA NA

MOTOR SPEED TAP - COOLING T2 T2 T2

RPM 1,050 1,050 1,050

EVAPORATOR DIAMETER X WIDTH (INCHES) 10 X 8 10 X 8 11 X 8

BLOWER RATED SCFM COOLING 1,300 1,600 1,600

HI EFFICIENCY COOLING CFM 1,300 1,600 1,600

5 TON NOMINAL COOLING CFM NA NA 1,800

FAN ONLY COOLINGCFM 1,200 1,400 1,600

MAX EXTERNAL STATIC PRESS ("w.c.) 0.5 0.5 0.5

EVAPORATOR FACE AREA (SQ. FT.) 6.2 6.2 7.0

COIL NUMBER OF ROWS 4 4 4

FINS PER INCH 14 14 14

GENERAL FILTER SIZE (SQ.FT.) (2) 20 x 20 x 1 (2) 20 x 20 x 1 (2) 20 x 25 x 1

INFORMATION DRAIN SIZE (INCHES) 3/4" 3/4" 3/4"

EXPANSION DEVICE (INDOOR / OUTDOOR) ORIFICE (0.072 / 0.065) ORIFICE (0.076 / 0.065) ORIFICE (0.088 / 0.071)

REFRIGERANT CHARGE R-410A (OZS.) 150 190 200

POWER SUPPLY CONDUIT KNOCKOUT SIZE (INCHES) 3/4, 1, 1-1/4 3/4, 1, 1-1/4 3/4, 1, 1-1/4

LOW VOLTAGE CONDUIT KNOCKOUT SIZE (INCHES) 1/2 1/2 1/2

LO PRESSURE SWITCH

OPENS / CLOSES PSIG 22 / 50 22 / 50 22 / 50

HI PRESSURE SWITCH - OPENS PSIG

OPENS / CLOSES PSIG 660 / 420 660 /420 660 / 420

SHIPPING WEIGHT (LBS.) 385 415 415

OPERATING WEIGHT (LBS.) 375 405 405

ACCESSORIES

GPH14[24-60]H41A*

Part Number Description

OT18-60A Outdoor Thermostat Kit w/Lockout Stat

OT/EHR18-60 Emergency Heat Relay Kit

HKR Electric Heat Kit

PCCP101-103 Roof Curb

PCP101-103 Downflow Plenum Kit

PCP101-103R8 Downflow Plenum Kit w/ R-8 Insulation

GPCED101-103 Downflow Economizer for GPC-(H) A/C - To Be Used With PCP101-103

GPHED101-103 Downflow Economizer for GPH-(H) Heat Pump - To Be Used With PCP101-103

GPCEH101-103 Horizontal Economizer for GPC-(H) A/C

GPHEH101-103 Horizontal Economizer for GPH-(H) Heat Pump

PCMD101-103 Manual Damper - To Be Used With PCP101-103

PCMDM101-103 Motorized Damper - To Be Used With PCP101-103

GPHMD101-103 Manual Damper for Horizontal Applications

SQRPCH101 Square to Round Adapters 16"&14"

SQRPCH102-103 Square to Round Adapters 18"&14"

SQRPC101 Square to Round Adapter - For Use With PCCP101-103 Curb 16" Rounds

SQRPC102-103 Square to Round Adapter For Use With PCCP101-103 Curb 18" Rounds

PCFR101-103 External Horizontal Filter Rack

PCEF101-103 Elbow & Flashing w/ R-8 Liner

CDK36 Flush Mount Concentric Duct Kit

CDK36515 Flush Mount Concentric Duct Kit w/ Filter

CDK36530 Step Down Concentric Duct Kit

CDK36535 Step Down Concentric Duct Kit w/ Filter

CDK4872 Flush Mount Concentric Duct Kit

CDK4872515 Flush Mount Concentric Duct Kit w/ Filter

CDK4872530 Step Down Concentric Duct Kit

CDK4872535 Step Down Concentric Duct Kit w/ Filter

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Goodman Wärmepumpe Handbücher

Goodman

Goodman SS-CPKF50 SS-CPKF50 Montageanleitung

Goodman

Goodman ComfortNet ASXC Series Betriebsanleitung

Goodman

Goodman APH16 M Series Bedienungsanleitung

Goodman

Goodman PH 15 SEER Series Bedienungsanleitung

Goodman

Goodman SSZ 14 SEER Bedienungsanleitung

Goodman

Goodman CPH COMMERCIAL SS-CPH90-150 Bedienungsanleitung

Goodman

Goodman SSZ 16 SEER Technisches Dokument

Goodman

Goodman R-410A Bedienungsanleitung

Goodman

Goodman SS-CPKF50 SS-CPKF50 Bedienungsanleitung

Goodman

Goodman SSZ 14 SEER Bedienungsanleitung

Goodman

Goodman DSX18 Bedienungsanleitung

Goodman

Goodman SS-GPH13MC Bedienungsanleitung

Goodman

Goodman GSZ11 Gebrauchs- und Pflegehandbuch

Goodman

Goodman PC Bedienungsanleitung

Goodman

Goodman GPH14H Bedienungsanleitung

Goodman

Goodman DSZ180601A Series Bedienungsanleitung

Goodman

Goodman GPH1524M41 Bedienungsanleitung

Goodman

Goodman ASX Betriebsanleitung

Goodman

Goodman GSZ16 Bedienungsanleitung

Goodman

Goodman GPH1324M41AB Gebrauchs- und Pflegehandbuch

Goodman

Goodman *PH 16 Betriebsanleitung

Goodman

Goodman GPH1424H41AB Gebrauchs- und Pflegehandbuch

Goodman

Goodman M Series Bedienungsanleitung

Goodman

Goodman GSC140481A Technisches Dokument

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung