Goodmans GCDR1955DAB Bedienungsanleitung

CD/DAB/FM Digital Radio

&DualAlarmClock

GCDR1955DAB

Goodmans product Information Helpline 08708730080

For improvement purposes, specification and design are subject to change without notice

Instruction Manual

SPECIFICATIONS

Programme Play.............................. Up to 20 memories

Earphone output............................... 20mW

Power requirement............................ AC 230V

3 x AAA Battery Clock Memory

Dimension........................................ 170(W) x195(H) x185(D)mm

Weight............................................. 1.88Kg not including battery (Main Unit)

TA B L E OF CONTENTS SAFETY PRECAUTIONS

1. As the laser beam used in this compact disc

player is harmful to the eyes, do not attempt

to disassemble the casing.

2. Stop operation immediately if any liquid or

solid object should fall into the cabinet. Unplug

the unit and have it checked by qualified

personnel.

3. Do not touch the lens or poke at it. if you do,

you may damage the lens and the player may

not operate properly.

4. Do not put anything in the safety slot. If you

do, the laser diode will be ON when the lid is

still opened.

5. This unit employs a laser. The use of controls

or adjustments or performance of procedures

other then those specified herein may result

in exposure to hazardous radiation.

WARNING

To prevent fire or shock harzard, do not expose

the unit to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified presonnel

only.

Important safeguards .....................................1

Important notes................................................2

Power Sources ...............................................3

Player Maintenance ........................................3

Disc cleaning, power failure ............................4

Player operation

Remote control locations ................................5

Location of controls .........................................6

Setting the clock..............................................7

Setting the wake-up time..................................7

Alarm function..................................................8

Volume operation..........................................9

Clock dimmer operation...................................9

DAB operation..................................................9

DAB operation............................................10

FM operation..................................................11

Display modes...............................................12

CD operation..................................................13

Factory reset..................................................14

Sleep function.................................................14

Product specifications....................................15

Troubleshooting guide....................................16

Goodmans product Information Helpline 08708730080

1. IMPORTANT SAFEGUARDS

For your convenience a mains plug with a fuse has been fitted to this appliance. For your safety please observe the following.

1. Should the fuse fail in the plug remove the plug from the wall socket and replace the fuse with a 3 Amp ASTA approved to BS1362

fuse.

2. Never use the plug without the fuse cover fitted. Replacement fuse covers are available from your dealer or most electrical retail

outlets.

3. IF the mains plug is cut off from the cable, rewire the replacement plug in accordance with the instruction given in this manual.

4. CAUTION: Under no circumstances should the discarded plug be inserted into the mains socket. To prevent a sock hazard carefully

dispose of the discarded plug. Do not leave the plug lying around where children might see it.

WARNING: To prevent fire of shock hazard do not expose this unit to rain or moisture.

CAUTION: DANGEROUS VOLTAGES EXIST INSIDE THIS UNIT, DO NOT REMOVE COVER (OR BACK). NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL DISCONNECT FROM

MAINS SUPPLY WHEN NOT IN USE.

MAINS PLUG WIRING DETAILS

accordance with following wiring codes: Thewires in this mains lead arecoloured in accordance with the

following wiring codes:

Blue-------------------------------------------Neutral

Brown----------------------------------------live

The wires in this mains lead must be connected to the terminals

in the plugs as follow:

Blue Wire-----------------------------------N or Black

Brown Wire--------------------------------L or Red

Only a 3 Amp fuse should be fitted in the plug or a 5 Amp fuse at

the distribution board.

WARNING: UNDER NO CIRCUMSTANCES MUST THE LIVE OR NEUTRAL WIRES BE

CONNECTED TO THE EARTH TERMINAL IN A 3-PIN MAINS PLUG.

This symbol means that this unit is double insulated.

An earth connection is not required.

CAUTION

CLASS 1 LASER PRODUCT

Use of Controls or adjustments or performance

of procedures other than those specified herein

may result in hazardous radiation exposure.

CLEANING

Always disconnect unit from power supply before

attempting to clean it.

Use soft cloth moistened with soapy water, wipe

gently.

Do not use solvents or abrasive material.

LASER SAFETY

This unit employs a laser. Only qualified service

personnel should attempt repair.

DANGER: INVISIBLE LASER RADIATION

WHEN OPEN AND INTERLOCK FAILED OR

DEFEATED. AVOID DIRECT EXPOSURE TO

BEAM.

CAUTION: HAZARDOUS LASER RADIATION

WHEN OPEN AND INTERLOCK DEFEATED.

Goodmans product Information Helpline 08708730080

Your hearing is very important to you and to us so please take care when operation this

equipment. The following guidelines are provided for your information.

ESTABLISH A SAFE SOUND LEVEL

Over time your hearing will adapt to continuous loud sounds and will give the

impression that the volume has in fact been reduced. What seems normal to you may

in fact be harmful. To guard against this BEFORE YOUR HEARING ADAPTSSset

the volume at a low level.

Slowly increase the level until you can hear comfortably and clearly and without

distortion.

Damage to your hearing is accumulative and is irreversible.

Any ringing or discomfort in the ears indicates that the volume is too loud.

Remember listening for prolonged period of time at high volume levels will harm your

hearing.

Once you have established a comfortable listening level, DO NOT INCREASE

THE SOUND LEVEL FURTHER.

The following list of typical sound levels may assist you in recognising just how loud you

have set the volume level.

DECIBEL

Level dB Example

30dB

THE FOLLOWING NOISE CAN BE HARMFUL UNDER CONSTANT EXPOSURE

80dB

100

120

140

180

Quiet library, soft whisper.

Living room, fridge freezer bedroom away from traffic.

Normal conversation, quiet office, light traffic.

Electric sewing machine.

Vacuum cleaner, hair dryer, noisy restaurant.

Average city traffic, alarm clock buzzer at 1 Metre, food mixer.

Motorcycle, heavy goods vehicle, petrol lawn mower.

Pneumatic drill, chain saw, garbage truck, discotec/night-club.

Rock band concert, thunderclap, fast train passing by.

THRESHOLD OF PAINN Gunshot, jet plane taking off.

Rocket Launching pad.

2. IMPORTANT NOTES

Goodmans product Information Helpline 08708730080

3. POWER SOURCES

1. Plug the AC 230V Power Cord into an AC

household outlet.

2. For battery back up, insert three (3 x AAA)

1.5V batteries (not included) into the battery

compartment observing correct polarities.

3. The batteries will maintain time function during

a power cut, but not display it.

4. Normal display and function will resume when

power is restored, replace the batteries

annually.

Note : This is an optional feature, no battery is

needed for normal operation.

Power connection

4. PLAYER MAINTENANCE

IMPORTANT : Disconnect from Main Supply

before cleaning.

Wipe with a soft cloth. If the cabinet is very dirty,

dampen the cloth with a weak solution of neutral

detergent and water, and then wipe clean.

Cleaning the Cabinet

A dirty lens will cause sound skipping and, if the

lens is very dirty, the CD may not work. Open

the disc cover and clean the lens as follow :

Dust Dry Particles

Using a camera lens brush/blower, blow on the

lens couple times, then wipe it lightly with the

brush to remove dust. Then, blow on the lens

once more.

Finger prints

If the lens cannot be cleaned by using a brush/

blower, use a dry cotton swab.

Cleaning the Lens

1.5VAAA

5. DISC CLEANING, POWER FAILURE

1. To handle a disc use only one of the two

following methods.

Note : Do not touch the rainbow-coloured side.

2. To wipe a disc, use only a soft cloth. Do not

use benzene or thinner which will damage

the disc. The disc should always be wiped in

a straight line from the centre to the edge. It

should never be wiped in a circular motion.

3. Never place the disc on other equipment or

near any heat source. Avoid positions where

the disc would be subjected to direct sunlight

for long periods.

Cleaning the Disc

When AC power is interrupted, both time and

alarm settings will be lost (unless 3 x AAA

batteries (not supplied) are installed) after power

is restored The digital display will blink to show

power was interrupted. You must reset time and

alarm times.

Power failure

Battery back up

1. Electronic products should never be

subjected to extreme temperatures nor high

humidity to ensure good performance and a

long life-time. The clock radio should not be

placed in bathing areas, or around stoves

and radiators, etc. Always leave sufficient

space around the unit for ventilation.

2. If necessary, only clean the cabinet of the

unit with a soft dampened piece of cloth. (be

sure the AC power cord is unplugged from

the outlet) Never use a polish or a strong

detergent for cleaning since this can damage

the finish of the cabinet.

Maintenance and care

To keep alarm time and time of day settings in

memory during a brief power failure or accidental

AC cord unplugged, install 3 x AAA batteries

(not supplied) into the Battery Compartment on

the rear of the unit.

6. REMOTE CONTROL LOCATIONS

Installing batteries into the

remote control unit

1. Press down on the triangular mark of the

compartment cover, and slide the cover off

to open the compartment.

2. Insert 2 x AAA or LR03 batteries in the

remote batteries in the remote control

observing to the polarity markings ( "+"

and "-" ) inside the compartment and

on the batteries.

3. Place the cover over the compartment,

press down lightly, and push it upward

until it snaps on.

** BATTERIES NOT INCLUDED **

1. STANDBY/AL/CD STOP BUTTON

2. CD/PLAY/PAUSE BUTTON

3. FM/DAB BUTTON

4. MUTE BUTTON

5. SKIP DN / FR / SELECT DN BUTTON

6. SKIP UP / FF / SELECT UP BUTTON

7. SLEEP BUTTON

8. SELECT BUTTON

9. VOLUME DN BUTTON

10. VOLUME UP BUTTON

7. LOCATION OF CONTROLS

1. CD DOOR

2. SNOOZE BUTTON

3. SPEAKER

4. IR SENSOR

5. STANDBY/AL/CD STOP BUTTON

6. CD PLAY/PAUSE BUTTON

7. FM/DAB BUTTON

8. REPEAT / AUTOTUNE BUTTON

9. RANDOM / INFO BUTTON

10. POWER ON/MUTE INDICATOR

11. ALARM 1 INDICATOR

12. SELECT BUTTON

13. SKIP DN / FR / SELECT DN BUTTON

14. SKIP UP / FF / SELECT UP BUTTON

15. CLOCK / CD DISPLAY

16. FM/DAB DISPLAY

17. CD DOOR OPEN BUTTON

18. CLOCK DIMMER BUTTON

19. SLEEP BUTTON

20. ALARM 1 BUTTON

21. ALARM 2 BUTTON

22. DISPLAY/AL SET BUTTON

23. SLEEP INDICATOR

24. ALARM 2 INDICATOR

25. PROGRAM/C-ADJ BUTTON

26. VOLUME UP BUTTON

27. VOLUME DN BUTTON

28. HEADPHONE JACK

29. PRESET 3 BUTTON

30. PRESET 1 BUTTON

31. PRESET 2 BUTTON

32. PRESET 4 BUTTON

33. DAB/FM WIRE AERIAL

34. BATTERY DOOR

35. AC POWER CORD

13 14

11 10 23 24

8. SETTING THE CLOCK

When the unit is connected to the power for the

first time, it will be in Standby, the red power indi-

cator will come on and the LED display will show

"0:00" and will flash. Do not press the STANDBY

button, the clock must be set in the Standby mode.

(F.1)

1. Ensure the unit is in Standby mode (Standby

indicator is ON).

2. Press and hold the PROGRAM/C-ADJ button

until the "hour" digit flashes in the display, then

press the SKIP UP/FF and the SKIP DN/FR

buttons to set the correct hour. (F.2)

3. Press the PROGRAM/C-ADJ button to confirm

the hour and the "minute" digits will flash, press

the SKIP UP/FF and the SKIP DN/FR buttons

to set the correct minute.

9. SETTING THE WAKE-UP TIME

1. Press and hold the DISPLAY/AL SET button for more than 2 seconds until the "hour" digit flash in the

display, the Alarm 1 LED indicator will also flash, press the SKIP UP/FF and the SKIP DN/FR

buttons to set the desired hour.

2. Press the PROGRAM/C-ADJ button to confirm the hour and the "minute" digit will flash, press the

SKIP UP/FF and the SKIP DN/FR buttons to set the desired minute.

3. AgainpressthePROGRAM/C-ADJbuttontoconfirmandthetimefortheAlarm1isset.

4. The Alarm 2 LED indicator and the "hour" digit in the display will then flash, repeat the above

proceduretosetthetimefortheAlarm2.

5. To check the Alarm time, press the DISPLAY/AL SET button, repeatedly until the corresponding

LED indicator flashes. The time shown in the clock display is the time set for that alarm.

4. Again press the PROGRAM/C-ADJ button to confirm and the clock is set. (F.3)

10. ALARM FUNCTION

This unit incorporates an identical Dual Alarm function. You can set the alarm to wake you to an

electronic buzzer tone, the radio or your favourite CD.

First press the DISPLAY/AL SET button on the front panel to check the wake up time settings. Adjust

the wake up time if necessary. Then press the ALARM 1 or the ALARM 2 button to activate the Alarm

and its associated wake up modes as described in "setting the wake up time" on page 7. The LED

indicators will light up in three different colours to show the different wake up mode settings:

Wake to Buzzer (Green indicator)

1. Repeatedly press the ALARM button (1 or 2) until the LED indicator turn green.

2. Press the STANDBY button to turn the unit to Standby.

3. At the selected wake up time, the buzzer will sound. It will continue for one hour and then shut off

automatically. To stop the alarm during this hour, press STANDBY button once.

4. When the buzzer is sounding, press the VOL UP or DN button to set the default buzzer level (high

or low).

Wake to FM/DAB (Red indicator)

1. Repeatedly press the ALARM button (1 or 2) until the LED indicator turns red.

2. Press the FM/DAB button to select FM or DAB mode, tune to the desired radio station and adjust

the volume to a sufficient level.

3. Press the STANDBY button to turn the unit to Standby.

4. Attheselectedwakeuptime,theradiowillturnon.Itwillcontinueforonehourandthenshutoff

automatically. To stop the radio during this hour, press STANDBY button once.

Wake to CD (Orange indicator)

1. Repeatedly press the ALARM button (1 or 2) until the LED indicator goes to orange.

2. CD will flash in the clock display and the track number, press the SKIP UP/FF and the SKIP DN/FR

buttons to select the desired wake up track.

3. LoadtheCD,beginplaybackandadjustthevolumetoasufficientlevel.

4. Press the STANDBY button to turn the unit to Standby.

5. At the selected wake up time, the CD will begin to play from the selected track. It will continue for

one hour or until the end of the disc, and then shut off automatically. To stop the CD during this time,

press the STANDBY button once.

6. If the CD is not recognized or no disc is inserted, the buzzer will sound.

Automatic alarm repeat

The alarm will automatically repeat each day at the selected wake up time as long as the Alarm

indicators are lit. To cancel the alarm, press the ALARM button (1 or 2) until the indicators are turned off.

Note: The Alarm that is set to turn on first will have the priority and it would c ontinue

for a one hour duration, the Snooze func tion will just switch off this Alarm off tempo-

rary during this duration, so if the second Alarm is set to turn on in this period, it will

not func tion. But if the first Alarm i s switched off before the time, the se c ond alarm

is set for, then the sec ond Alarm will be activated.

Inhaltsverzeichnis

Beliebte DAB-Radio Handbücher anderer Marken

Sangean

Sangean WFR-29D Bedienungsanleitung