Goodmans GMN10040MP3 Bedienungsanleitung

Instruction manual

Mini sound system

with CD-R/MP3CD playback

GMN10040MP3

FCS

ImportantSafeguards

WORTH

knowing

PREFITTED MAINS PLUGS

For your convenience a mains plug has been fitted to this appliance. For your safety

please observe the following information.

1. Should the fuse in the plug fail remove the plug from the wall socket and replace

the fuse with a 3 Amp ASTA approved to BS 1362 fuse.

2. Never use the plug without the fuse cover fitted. Replacement fuse covers are

available from your dealer or most electronical retail outlets.

3. If the cable of the mains plug is cut off the cable, rewire the replacement plug in

accordance with the instructions given in this manual.

4. CAUTION : Under no circumstances should the discarded plug be inserted into

main socket. To prevent a shock hazard carefully dispose of the discarded plug.

Do not leave the plug lying around where children might see it.

WARNING : to prevent fire or shock hazard do not expose this unit to rain or moisture.

CAUTION : DANGEROUS VOLTAGES EXIST INSIDE THIS UNIT, DO NOT

REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE, REFER SERVICING TO

QUALIFIED SERVICE PERSONAL. DISCONNECT FROM MAINS

SUPPLY WHEN NOT IN USE.

The wires in this mains lead are colured in

accordance with the following wiring codes:

Blue ------------------------------------------- Neutral

Brown --------------------------------------------- Live

The wires in this main lead must be connected

to the terminals in the plugs as follows:

Blue Wire ------------------------------- N or Black

Brown Wire ------------------------------- L or Red

Onlya3Ampfuseshouldbefittedintheplug

or a 5 Amp fuse at the distribution board.

WARNING : UNDER NO CIRCUMSTANCES MUST THE LIVE OR NEUTRAL

WIRES BE CONNECTED TO THE EARTH TERMINAL IN A 3-PIN MAINS PLUG.

this symbol means that this unit is double insulated.

An earth connection is not required.

FUSE

BS1362

BROWN

(Live

BLUE

(Netural)

Cord Clamp

PLUG WIRING DETAILS

Controls

The remote control .......................................................................................................................... 4

Sound control ................................................................................................................................. 5

On the main unit ........................................................................................................................... 6/7

Installation / Connections

Placing your sound system components, Remote control and batteries ..................................... 8

Connection ...................................................................................................................................... 9

Radio listening

Tuning stations, Programming station presets, Selecting station presets ................................. 10

CD[MP3] playback

CD/MP3 playback, Displaying information, Skipping, Searching ............................................... 11

Folder skip, MP3 file Search ......................................................................................................... 12

Programmed playback, Intro scan playback ............................................................................... 13

Repeat playback, Random playback ........................................................................................... 14

Tape playback

Tape playback , Winding, Continuous playback ......................................................................... 15

Recording

Recording stations, Recording from a connected device ........................................................... 16

Recording CDs with synchro start, Recording from another tape (dubbing) ............................. 17

Timer and clock

Setting the clock, Displaying the time, Setting the sleep timer ................................................... 18

Setting the timer, Timer (record) stand-by on/off ......................................................................... 19

Appendix

Troubleshooting, Cleaning the audio heads of the tape deck .................................................... 20

Compact discs, Accessories, Technical data .............................................................................. 21

Contents

WORTH

knowing

Before use, please read the chapter "Installation/connections"

WORTH

knowing

Precautions

Please keep the sound system's guarantee card and receipt safe for warranty

purposes.

1010

Before use read through this manual carefully.

Make sure the rating of the household electricity supply matches that shown on the

back of the sound system.

Refer to this chapter and the "Installation / connections" chapter (page 8/9) to help

with the installation and adjustments of this sound system.

Do not ...

... expose the sound system to high levels of humidity and heat, to avoid the risk of fire

andelectricshock.

... connect the sound system to the power supply if it has just been moved from a cold

to a warm environment. This can result in condensation inside the system and cause

the system to malfunction.

Wait around two hours to allow it to reach room temperature.

... put in any substance through the gaps in the back cover.

Make sure....

... the system is placed on a stable, flat surface.

... the system is placed where there is good ventilation all around.

... the system is only cleaned with a soft, line-free cloth, do not use aggressive or

alcohol-based cleaning agents.

... the power supply is disconnected if the system appears to be working incorrectly, is

making an unusual sound, has a strange smell, has smoke emitting from it or liquids

have got inside it.

Have a qualified technician check the system.

... the power supply and aerial is disconnected if you will not be using the system for a

long period or during a thunderstorm.

... this apparatus shall not be exposed to dripping or splashing water and that no

objects filled with liquids, such as vases shall be placed on the apparatus.

Foryourownsafety!

There are no components in this sound system that can be serviced or

repaired.

Do not open the case of the sound system.

Only allow qualified personnel to repair or service this set.

"Class 1 Laser Product" : Do not override the safety locks around the

laser unit of the CD player : Laser beams can damage eyes!

This sound system is designed for continuous operation.

Switching it off does not disconnect it from the mains (stand-by).

To disconnect it from the mains, unplug at the mains socket.

GMN10040MP3

CONTROLS

Theremotecontrol

Please note, the instructions guiden in this is refer mainly it the remote but the main functions

buttons are also available on the front of the main unit.

Press the POWER button or FUNCTION buttons (TAPE, TUNER, AUX, CD) to turn on the power.

4 5

GMN10040MP3

FCS

Power on (stand-by).

Press repeatedly to select tape, tuner, AUX or CD player.

Display the current time.

Set the time for the unit to turn on also turn timer on / off.

Set the period after which the unit will turn off.

Select FM or MW radio.

Select FM mono for weak stereo reception (tuner mode) or switch

between tape decks 1 and 2.

Mute (on / off) the volume for a while, e.g. during a telephone call.

Set a programm for CD playback.

Select random playback.

Select repeat playback..

Direct access to each of the CDs loaded.

Start CD playback or select station presets.

Stop or cancel values and functions.

Tune in stations, set values in programming, fast reverse or advance

tape and CD.

For a short pause during recording of a tape or CD play or to advance in

a programming (e.g. clock set).

Set the volume level.

Add sound effects to the sound output.

Bass enhancement or 3ST (on / off), see page 5.

Press and hold to select 3ST sound mode.

Show the name of folder the currently playing track is in (MP3 CD only).

Select intro play for CD.

Display the ID3 tag information (MP3 CD playback only).

Soundcontrol

Onthe

remotecontrol

Onthe

mainunit

Volume control

Rotate the volume control or press the column buttons on the remote to

adjust the volume.

(MIN, VOL 1 ~ VOL 28, MAX).

3ST(3 Stereo)

This button adds the 3ST music effect to the sound output.

Ultra Bass Sound

Press this button on the remote control or main unit to enhance the low

frequency (Bass) sounds.

Mute

Press this button on the remote control to mute the sound.

GEQ

Press this button on the remote control to add sound effects to the audio

output.

Mono/Stereo

If there is to much noise (hiss) when listening to an FM station in stereo

press this button to change to mono reception which will reduce the amount

of noise heard. To return to stereo reception press this button again.

Demo/Display

Press this button on the main unit to switches between normal display mode

and a demonstration shown on display.

GMN10040MP3

CONTROLS

Place your sound system

horizontally on a flat, steady base and in a position so that air can circulate around it for

ventilation.

away from humidity and heat, magnetic fields, such as those from loudspeakers etc.,

and with no heavy objects placed on top.

Remote control buttons

see page 4.

Onthemainunit

Turn system power ON(stand-by).

Press this button to turn the unit on from standby. Press this button

again to turn the unit back to standby.

Tune in stations, to set values in programming, to select tracks.

CONTROLS

Direct access to any discs already loaded into the CD tray.

Open or close the disc compartment to load / unload CDs.

Select the next disc inserted into the CD tray.

Tape compartment 2 for playing and recording tapes.

Tape compartment 1 for playing tapes.

To set the volume level.

DISPLAY / DEMO : to switch between the system's display and a

display demonstration.

To dub a tape at high or normal speed with synchronized start of

both, playing and recording tapes.

To dub a CD with synchronized start of disc and tape.

Start tape recording.

Headphone socket.

Insert a set of headphones and sound wll be heard through the

headphones (the loudspeakers will automatically be muted).

UBS(Ultra Bass Sound)

Press this button to enhance the low frequency (Bass) sounds.

GEQ.

Press this button to add sound effects to the audio output.

Turn on/off the 3 stereo effect, see page 5.

Stop playback and recording or clear

values and functions.

To start forward play tape/disc, to select station

presets and to enter selected track.

Pause playback/recording of CD / Tape or to set/enter a value

when programming a CD or setting the clock/timer.

Tune in stations, to set values in when programming (i.e. when

setting the clock or creating a CD playback programme) to fast

reverse or advance tape and CD.

Select station presets and return MP3 normal display mode.

6 7

GMN10040MP3

FCS

Direct function buttons

Press tape to select tape 1, press again to select tape 2.

Press tuner to select tuner, press again to change the band

between FM and MW.

Press AUX to listen to sound from external equipment connected to

the AUX input on the rear of the unit.

Press CD to listen to a CD that is already loaded into the CD disc

tray.

Connections

INSTALLATION/

CONNECTIONS

INSTALLATION/

CONNECTIONS

Placingyoursoundsystemcomponents

Remotecontrolandbatteries

Optimal Stereo Position

Batteries for remote control unit are not provided.

Please protect your environment! As batteries contain certain

toxic substances they pollute the environment if not properly

disposed of. Please contact your local authority to find out how

to dispose of used batteries in your area.

Make sure the batteries are always of the same type and age, nd remove them

from the remote control if you are not using it for a long period.

8 9

GMN10040MP3

FCS

Fit the batteries while observing the

and symbols in the compartment.

Right

speaker Left

speaker

Make sure the rating of your household electricity supply matches that shown on the back of the sound system.

Do not stack objects on top of the sound system.

Do not block the ventilation holes of the sound system.

Place the system so that air can circulate freely.

Switch devices off when connecting or disconnecting.

Do not expose the sound system to high levels of humidity and heat, to avoid the risk of fire and electric shock.

Be sure the power supply and aerial are disconnected if the system is not going to be used for a long period or

during a thunderstorm.

Be sure to read the precautions on page 2.

Push here

3. Connect the speaker cables.

Connect the wires correctly

(wire with the black to the black

terminals other wire to the red

terminal)

Push here

4. Plug a device like a video

recorder, TV set or minidisc,

etc. here. Be sure to

connect sockets and plug of

thesamecolour.

1. FM aerial

2. Plug the supplied MW

aerial here.

Push here

CD/MP3playback

CD[MP3]

playback

RADIO

listening

Tuningstations

Programmingstationpresets

Selectingstationpresets

Use to select preset station,

Up to 30 FM / 15 MW stations can be stored.

Tune to the required station as shown

above.

Store.

The system assigns the station to

a preset number beginning with 1, and

then one after another (for example the

it no presets are already stored the

station will be stored in preset 1. If

presets 1~3 are already used than the

station will be stored in preset 4.)

GMN10040MP3

FCS

If you try to store a 31st FM / 16th MW station, the display will show "FULL".

To clear a preset station, select the preset, press , then for 3

seconds.

Select the tuner.

Select the band (FM/MW) the station is on.

Press repeatedly to manually tune.

Press and hold to start automatic tuning.

If there is to much background noise when

listening to a station in FM stereo, press

this button to listen in mono " (

) " will no

longer show in the display. To return the

FM stereo mode press this button again "

(

) " will be shown on the display again.

Select the CD function.

Open the disc compartment to load a disc.

Insert disc with the label facing upwards.

To insert 3 discs, place 2 discs into the slots on the disc tray and turn the tray

for the third slot, using DISC CHANGE button.

Commence playback with the first track or MP3 file of the selected

disc.

Start playback.

The currently selected disc is the disc to

the left when the CD compartment is opened.

Pause playback.

Stop playback.

on the main unit

On the system select the CD function, by pressing the CD button.

When the disc stops, the main unit shows its total tracks/times (standard CD) or total folders/files (MP3 CD).

During playback the main unit shows the current disc number, the current track(file) number, and the track’s(file’s) elapsed

time.

Displayinginformation(MP3CDsonly)

Press repeatedly to display ...

FOLDER FILE ARTIST ALBUM TITLE

The main unit can display max 19 characters of MP3 file/folder name or ID3

tag information.

Skipping

Briefly press to skip to next/previous track.

The system shows the current playing MP3 file/folder name or ID3 tag information.

Searching

Press and hold to search for a particular section of the disc.

Important note : During search on MP3 discs no sound will be heard

through the speakers.

hold pressed

CD[MP3]

playback

CD[MP3]

playback folderskip(MP3 CDonly) Programmedplayback

When the MP3 disc is stopped, press

“FOLDER” button to display the current

folder name.

Press the TUNE UP/DOWN button

repeatedly to select the required folder.

Start playback.

MP3filesearch

When file name is displayed (press ID3

button repeatedly until *FILE* is shown

on the display), press SET button to

search by MP3 file name.

Use these buttons to select the first

character of the desired MP3 file. If the

system displays “[NONE]”, there are no

files that start with that letter.

Use these buttons to select the required

file that starts with the selected letter. To

cancel search mode press the “CLEAR

button.

Start playback with the selected file.

During playback, discs damaged with dirt or a scratch may make a pop sound,

clipping sound or cut off.

Tracks or MP3 files with damaged or corrupted parts are skipped or forwarded to

next track or MP3 file.

Only supported file type will have the extension MP3 with MP3 encoding.

When searching by MP3 file or folder name, the folders and files are sorted in a

alphabetical order.

Total 255 MP3 files and 128 folders within a disc can be recognized.

The main unit can playback CD-R/RW made for ISO9660 file format and disc at once

method. For other file format or packet writing method, it will not playback the discs.

TIP : To shorten the reading time of MP3 discs....

Make a disc at a lower speed, single session disc closed CD-R for ISO9660.

Press this button to confirm the selected

letter.

12 13

GMN10040MP3

FCS

1. Stop the disc (programmes can only be created during stop mode).

2. Select the programme function.

3. Choose a disc.

4. Select a track number to be programmed.

5. Store this number in the programme.

Upto30trackscanbeprogrammedbyrepeatingstep3to5.

DISC CHANGE button has no effect in programming.

Play your programme.

Search and skip functions as normal during CD programm playback.

Stop Playback

To cancel the CD programme playback, press this button twice.

Introscanplayback

To playback the first 10 second of each track or MP3 file.

To cancel intro scan playback, press the INTRO again or PLAY button, and

then “INTRO” will no longer be shown in the display.

The system will not play an unfinalized CD-R disc.

Discs recorded by personal computer or high speed recording may not play (or cause noise) depending on recording

format. It is recommended to use and play discs recorded at as low speed as possible.

TAPE 1 : Will only playback tapes.

TAPE 2 : To play back tapes and to record tapes.

Tapeplayback

Winding

Continuousplayback

TAPE

playback

SelectTAPE1(TA1isshowninthedisplayalongwithacounter)or

TAPE 2 (TA2 is shown in the display along with a counter) function.

Open either tape compartment to load the tape.

Be sure to have the open part of the cassette downward and the left hand

spool fully wound. Push the compartment door gently to close.

Start playback.

Stop playback.

Fast rewind or forward the tape.

Load tapes into both compartments.

Select the TAPE 1 function.

button on the main unit

Set TAPE 1 to play.

After playing one side of TAPE 1, the unit will commence with TAPE 2

automatically.

On the main unit select the tape function using the TAPE 1/2 button.

The tape counter resets to "0000" when a tape compartment is opened ("0000" is not necessarily the beginning of the tape).

Select the random function, press

repeatedly ...

to play tracks or MP3 files of

the current disc in a random

order.

to play all tracks from disc 1,

2, and 3 in a random order.

To cancel random playback, press the

button repeatedly until "RANDOM " is no

longer shown in the display .

CD[MP3]

playback Repeatplayback

Randomplayback

GMN10040MP3

FCS

Press repeatedly...

to repeat the current track or

MP3 file,

to repeat the current disc,

to repeat all discs.

To cancel repeat playback, repeatedly

press the button until "REPEAT"

disappears from the display .

You can repeat a programme

during programme playback.

RecordingCDswithsynchrostart

Recordingfromanothertape(dubbing)

RECORDING

Recordingstations

Recordingfromaconnecteddevice

Select the TUNER function.

Select the band.

Tune to the required the station or

select a stored preset.

(see also page 10).

Start the recording.

Press to pause recording, press again

to resume.

Stop the recording.

Select the AUX function.

Make sure the audio output of the device

is properly connected (TV set, video

recorder or minidisc, etc.) to the AUX input

sockets on the back of the main unit (see

also page 9).

Start the recording.

Press to pause recording, press again

to resume.

Stop the recording.

Select the CD function.

Open the disc compartment to load a disc.

Press again to close the disc compartment.

Selectthedisctoberecorded.

Stop CD playback before the recording is started.

Start the recording.

Stop the recording.

Select the TAPE function.

LoadatapewithenoughfreespaceintoTAPE2.

Load the prerecorded tape into TAPE 1.

Start your dubbing by selecting dubbing speed:

"Hi-DUB" : copy at double speed = half the time,

"DUB" : copy at normal tape speed.

Stop the recording.

The synchro start function is an easy way of copying (tracks of) CDs to a tape : One press of a button starts both CD playing and tape

recording at the right time.

insert the tape with the open part of the cassette downward and the left hand spool fully wound

on the left.

Close the compartment door again, pushing it gently.

If you want to start at the current position, press REC button.

Use only good quality tape cassettes.

- Keep cassettes away from excessive moisture or dust, magnetic and

electrical fields (loudspeakers and computer monitors, for example)

- Always wind the tape to the beginning when you have finished.

Store with the full spool at the bottom and with the cassette in its cover.

You can protect your precious recordings from being wiped by breaking

out the safety tab on the side of the cassette.

Should you wish to re-use the tape after removing the tab, cover the hole with adhesive tape.

16 17

GMN10040MP3

FCS

on the main unit

onthemainunit

Inhaltsverzeichnis

Andere Goodmans Stereoanlage Handbücher

Goodmans

Goodmans MICRO 1465i Bedienungsanleitung

Goodmans

Goodmans GMC01 Bedienungsanleitung

Goodmans

Goodmans Micro 1990 DVDF Bedienungsanleitung

Goodmans

Goodmans GMC6039DVD Bedienungsanleitung

Goodmans

Goodmans MICRO1106DAB Bedienungsanleitung

Goodmans

Goodmans MICRO1109IP Bedienungsanleitung

Goodmans

Goodmans GSPK30IP Bedienungsanleitung

Goodmans

Goodmans 4160AV Bedienungsanleitung

Goodmans

Goodmans Micro 1455 Bedienungsanleitung

Goodmans

Goodmans MICRODAB18BT Bedienungsanleitung

Goodmans

Goodmans 4214 Bedienungsanleitung

Goodmans

Goodmans 2719 Bedienungsanleitung

Goodmans

Goodmans GMC 1034DAB Bedienungsanleitung

Goodmans

Goodmans 6160 Bedienungsanleitung

Goodmans

Goodmans GDVX702 Bedienungsanleitung

Goodmans

Goodmans MICRO1470DABI Bedienungsanleitung

Goodmans

Goodmans MICRODAB10 Bedienungsanleitung

Goodmans

Goodmans MICRO1467I Bedienungsanleitung

Goodmans

Goodmans GMN02BT Bedienungsanleitung

Goodmans

Goodmans GPS165MP3R Bedienungsanleitung

Goodmans

Goodmans 4225MP3 Bedienungsanleitung

Goodmans

Goodmans MICRO 1109 Bedienungsanleitung

Goodmans

Goodmans MICRODAB16BT Bedienungsanleitung

Goodmans

Goodmans GMS950R Bedienungsanleitung

Beliebte Stereoanlage Handbücher anderer Marken

LG CM3330B Bedienungsanleitung

Sony

Sony SS-CEP50 Bedienungsanleitung

Cetacea Sound

Cetacea Sound CVS-II Bedienungsanleitung

Denon

Denon UCD-250 Bedienungsanleitung

Sanyo

Sanyo DC-MX41i Bedienungsanleitung

Sharp

Sharp CD-ES600V Bedienungsanleitung

Exibel

Exibel BDX600-UK Bedienungsanleitung

Sanyo

Sanyo DC-F320 Bedienungsanleitung

Philips

Philips FWM583X Bedienungsanleitung

Sharp

Sharp CD-C462 Bedienungsanleitung

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio Bedienungsanleitung

Aiwa

Aiwa XR-EM70 Bedienungsanleitung

Cyrus

Cyrus Lyric Bedienungsanleitung

Philips

Philips MCM159/98 Bedienungsanleitung

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C Bedienungsanleitung

RCA

RCA RS3965SB Bedienungsanleitung

Sharp

Sharp XL-UH240 Bedienungsanleitung

Philips

Philips FW 690 Bedienungsanleitung