Goosky S2 Bedienungsanleitung
Flight Control Setting
Turn on the GOOSKY T8 transmitter, press the BIND button for 3 times
after the helicopter is powered on. The blue light flashes quickly. Keep
the transmitter less than one meter away from the flight control. The
flight control passes self-detection when the blue light is solid on. Then
the binding is done.
Turn on the Futaba transmitter, adjust the communication protocol to
(S-FHSS). Long press and hold the BIND button when the aircraft is
powered on, the blue light flashes quickly then. Keep the transmitter
less than one meter away from the flight control. The flight control
passes self-detection when the blue light is solid on. Then the binding is
done.
<Schematic diagram of flight control parameter adjustment>
SET setting menu button SERVO servo midpoint setting
RUD direction parameter adjustment mode PITCH pitch setting
ELE up and down parameter adjustment mode SPEED speed indicator
AIL Aileron tuning mode AGILE sensitivity indicator
S1 On/Off Attitude Mode GYRO sensitivity indicator
Note: Bind the remote controller to the aircraft, and wait for the flight controller to
initialize. Make flight control settings after initialiazation.
Long Press and hold SET for 3 seconds → RUD is solid on → SPEED flashes
Direction hovering speed setting
Long press the SET button for 3 seconds to enter the tuning mode.
Short press the SET button until the RUD indicator is solid on in
white, the SPEED blue light flashes, and the factory default hover
speed SPEED flashes for 5 times.
Then Use the Elevation of the remote control to raise and lower the
gear forward and downshift to adjust the hovering speed. The
number of consecutive flashes represents the gear level. The
highest gear is 9 gears and the lowest gear is 1 gear. After
completion, press and hold the SET button for 3 seconds to exit
and save, then the indicator light turns off.
<Direction feel setting>
RUD is solid on → click SET → GYRO flashes
Direction Hovering sensitivity setting
Press and hold the SET button for 3 seconds to enter the tuning
mode, short press the SET button until the indicator light RUD is
solid on, GYRO flashes, the factory default sensitivity GYRO
flashes 5 times, use the remote control to raise and lower the gear
forward and downshift to adjust the hovering Sensitivity, the
number of consecutive flashes represents the gear level, the
highest gear is 9 gears, and the low gear is 1 gear. After completion,
press and hold the SET button for 3 seconds to exit and save, then
the indicator light turns off.
＜Elevation feel setting＞
Press and hold SET for 3 seconds → ELE is Solid on → SPEED flashes
Press and hold the SET button for 3 seconds to enter the tuning
mode. Short press the SET button to select the option until the
indicator light ELE is always on, SPEED flashes, the factory default
flip speed SPEED flashes 5 times. Use the remote control to raise
and lower forward and downshift to adjust the up and down Rolling
speed. The number of consecutive flashes represents the gear
level. The highest gear is 9 gears, and the lowest gear is 1 gear.
After completion, press and hold the SET button for 3 seconds to
exit the save and the indicator light turns off.
＜Elevation feel setting＞
ELE is solid on → click SET → AGILE flashes
Elevation sensitivity setting
Press and hold the SET button for 3 seconds to enter the tuning
mode. Short press the SET button until the indicator light ELE is
solid on, AGILE flashes, the factory default value is AGILE flashes 5
times. Use the remote control to raise and lower the gear forward
and downshift to adjust the up and down Sensitivity. The number of
consecutive flashes represents the gear level. The highest gear is 9
gears, and the lowest gear is 1 gear. After completion, press and
hold the SET button for 3 seconds to exit the save and the indicator
light turns off.
＜Elevation feel setting＞
ELE is solid on → click SET → GYRO flashes
Elevation sensitivity setting
Press and hold the SET button for 3 seconds to enter the tuning mode.
Short press the SET button until the indicator light ELE is solid on, GYRO
flashes, and the factory default sensitivity is GYRO flashes 5 times. Use
the remote control to raise and lower the gear forward and downshift to
adjust Lifting sensitivity. The number of consecutive flashes represents
the gear level, the highest gear is 9 gears, and the lowest gear is 1 gear.
After completion, press and hold the SET button for 3 seconds to exit the
save, and the indicator light turns off.
<Aileron feel setting>
Long press SET for 3 seconds →AIL is solid on →SPEED flashes
Aileron rollover rate setting
Press and hold the SET button for 3 seconds to enter the adjustment
mode. Short press the SET button to select the AIL white light is solid on,
the SPEED blue light flashes, and the factory default flip speed SPEED
flashes 5 times. Use the remote control to lift and shift forward and
downshift to adjust the aileron flip rate. The number of consecutive
flashes represents the gear level. The highest gear is 9 gears and the
lowest gear is 1 gear. After completion, press and hold the SET button for
3 seconds to exit the save, and the indicator light turns off.
<Aileron feel setting>
AIL is solid on → click SET → AGILE flashes
Aileron sensitivity setting
Press and hold the SET button for 3 seconds to enter the adjustment
mode. Short press the SET button to select the AIL white light is solid on,
the AGILE blue light flashes, and the factory default AGILE flashes 5 times.
Use the remote control to raise and lower gears forward and downshift
to adjust the aileron sensitivity. The number of consecutive flashes
represents the gear level. The highest gear is 9 gears and the lowest gear
is 1 gear. After completion, press and hold the SET button for 3 seconds
to exit the save, and the indicator light turns off.
Andere Handbücher für S2
3
Andere Goosky Controller Handbücher
