Graco Dyna-Star 25U218 Bedienungsanleitung

3A6932D

Instructions

Compact Dyna-Star®

Auto-Fill Shut Off Kit

For use with Compact Dyna-Star Electric Pump to automatically stop filling Graco grease

tanks. For grease lubrication systems only. For professional use only.

Not approved for use in explosive atmospheres or hazardous (classified) locations.

Model

25P686 Auto-Fill Shut Off

25P687 Auto-Fill Shut Off with Follower Plate

(12 and 20 liter)

25U218 Auto-Fill Shut Off with Follower Plate

(60 lbs)

3500 psi (24.1 MPa, 241.3 bar) Maximum Working Pressure

Related Manuals

3A6941 - Compact Dyna-Star Electric Pump Manual

333393 - Fill Valve

Important Safety Instructions

Read all warnings and instructions in this

manual and the Compact Dyna-Star

Pump instructions manual before using

the equipment. Save all instructions.

Contents

2 3A6932D

Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Pressure Relief Procedure . . . . . . . . . . . . . . . . . . 5

Auto-Fill Shut Off Installation . . . . . . . . . . . . . . . . 5

Follower Plate Installation (Part 25P687) . . . . . . . 8

Auto-Fill Shut Off Overview . . . . . . . . . . . . . . . . . . 11

Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Fill/Refill the Tank . . . . . . . . . . . . . . . . . . . . . . . . 12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Technical Specifications . . . . . . . . . . . . . . . . . . . . 15

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 16

Warnings

3A6932D 3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The

exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks.

When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.

Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this

manual where applicable.

WARNING

FIRE AND EXPLOSION HAZARD

When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be

aware that flammable fumes can ignite or explode. To help prevent fire and explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources, such as cigarettes and portable electric lamps.

• Ground all equipment in the work area.

• Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline.

• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.

• Use only grounded hoses.

•Stop operation immediately if static sparking occurs or you feel a shock. Do not use equipment

until you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

SKIN INJECTION HAZARD

High-pressure fluid from dispensing device, hose leaks, or ruptured components will pierce skin. This

may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical

treatment.

• Do not point dispensing device at anyone or at any part of the body.

• Do not put your hand over the fluid outlet.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Follow the Pressure Relief Procedure when you stop dispensing and before cleaning, checking, or

servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses and couplings daily. Replace worn or damaged parts immediately.

Warnings

4 3A6932D

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See Technical Specifications in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Specifi-

cations in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete

information about your material, request Safety Data Sheet (SDS) from distributor or retailer.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-

facturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and cre-

ate safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

MOVING PARTS HAZARD

Moving parts can pinch, cut or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,

follow the Pressure Relief Procedure and disconnect all power sources.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including

eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes but is not

limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

WARNING

Installation

3A6932D 5

Installation

Pressure Relief Procedure

To relieve pressure in the system, use two wrenches

working in opposite directions on the pump outlet

fitting to slowly loosen the fitting only until no more

lubricant or air is leaking from the fitting (FIG. 1).

Auto-Fill Shut Off Installation

1. Disconnect power to the system (FIG. 2).

2. Relieve pressure in the system following the

Pressure Relief Procedure, see page 5.

This equipment stays pressurized until pressure is

manually relieved. To help prevent serious injury from

pressurized fluid, such as skin injection, splashing

fluid and moving parts, follow the Pressure Relief

Procedure when you stop dispensing and before

cleaning, checking, or servicing the equipment.

FIG. 1

FIG. 2

Installation

6 3A6932D

3. Disconnect the main line from the pump outlet

(FIG. 3).

4. Loosen and remove the Compact Dyna-Star

Auto-Fill Shut Off plug. Dispose of the plug

according to local regulations (FIG. 4 and FIG. 5).

5. Grease the outside of the three (3) o-rings on the

Compact Dyna-Star Auto-Fill Shut Off cartridge

(FIG. 6).

6. Install the Compact Dyna-Star Auto-Fill Shut Off

cartridge (FIG. 6).

FIG. 3

FIG. 4

FIG. 5

FIG. 6

O-rings

Installation

3A6932D 7

7. Tighten the Compact Dyna-Star Auto-Fill Shut Off

cartridge (torque 45-55 ft-lb/61-74.5 N•m) (FIG. 7).

8. If the system currently has a follower plate,

installation is complete. For systems without a

follower plate, see Follower Plate Installation

(Part 25P687), page 8.

9. Use two wrenches working in opposite directions

on the pump outlet fitting to tighten (FIG. 1).

10. Reconnect the main line (FIG. 8).

11. Reconnect the power to the system (FIG. 9).

FIG. 7

FIG. 8

FIG. 9

Installation

8 3A6932D

Follower Plate Installation

(Part 25P687)

1. Disconnect power to the system (FIG. 10).

2. Relieve pressure in the system following the

Pressure Relief Procedure, see page 5.

3. Remove the nuts, bolts and the lifting hook from the

top of the tank and retain (FIG. 11).

NOTE: The lift ring for the 60 lbs tank is welded on

to the can and is not removable.

4. Lift the cover, tank gasket, and pump off of the tank

and set aside.

5. In a new installation, the center o-ring of the

follower plate and the tank walls should be greased

to allow for easier follower plate movement (FIG.

12).

6. Place the follower plate inside of the tank with the

follower plate top (marked “top”) facing upward

(FIG. 12).

FIG. 10

FIG. 11

Installation

3A6932D 9

7. Replace the cover, tank gasket, and pump on to the

tank (FIG. 13).

8. Replace the nuts, bolts, and lifting ring.

NOTE: The lift ring for the 60 lbs tank is welded

onto the cover and is not removable.

9. Tighten (torque 10-12 ft-lb/13.6-16.3 N•m).

10. Reconnect the main line to the pump outlet (FIG.

14).

FIG. 12

Grease

FIG. 13

Installation

10 3A6932D

11. Reconnect the power to the system (FIG. 15).

FIG. 14

FIG. 15

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Steuereinheit Handbücher

Graco

Graco 205612 Bedienungsanleitung

Graco

Graco 222-411 Datenblatt

Graco

Graco XM PFP Bedienungsanleitung

Graco

Graco CleanShot Bedienungsanleitung

Graco

Graco Dispensit-710 Bedienungsanleitung

Graco

Graco Series E Bedienungsanleitung

Graco

Graco 244920 Bedienungsanleitung

Graco

Graco 256994 Bedienungsanleitung

Graco

Graco PD44 Leitfaden

Graco

Graco Gun Flush Box 570046 Bedienungsanleitung

Graco

Graco Pro-Shot A Series Bedienungsanleitung

Graco

Graco CGM 25B127 Stücklistenhandbuch

Graco

Graco PD44 Fehlerbehebungshandbuch

Graco

Graco 24L096 Bedienungsanleitung

Graco

Graco E-Flo B Series Stücklistenhandbuch

Graco

Graco B52100 Stücklistenhandbuch

Graco

Graco Reactor 25D612 Bedienungsanleitung

Graco

Graco Dispensit 1052 Fehlerbehebungshandbuch

Graco

Graco 208390 Bedienungsanleitung

Graco

Graco Dyna-Star 77X540 Bedienungsanleitung

Graco

Graco Cleanshot 244162 Bedienungsanleitung

Graco

Graco LDP5 Bedienungsanleitung

Graco

Graco C Series Datenblatt

Graco

Graco CSP Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung

Flyron

Flyron FN-BC04 Bedienungsanleitung