Graco 214895 Bedienungsanleitung

STAINLESS STEEL, WATERBASE COMPATIBLE

Fluid Pressure Regulators

Used to regulate fluid pressure in lo pressure systems only.

Fluid Flow up to 3 GPM (11 liters/min)

Instructions--Parts List

307212ZAG

Important Safety Instructions

Read all warnings and instructions in this manual.

Save these instructions.

See page 2 for Ta le of Contents. See page 3 for

List of Models.

2 307212

Table of Contents

Models 3........................................

Warnings 5......................................

Installation 6.....................................

Operation 8.....................................

Trou leshooting 11...............................

Service 12......................................

Parts 16........................................

Dimensions 21...................................

TechnicalData 22................................

PerformanceCharts 23...........................

Warranty 24.....................................

GracoInformation 24.............................

3307212

Models

Spring Operated Fluid Regulators

Part No. Series Maximum Fluid Inlet

Pressure, psi (kPa, bar)

Regulated Pressure

Range, psi (kPa, bar)

Gauge Gauge Pressure

Range,

psi (kPa, bar)

214895 H 250 (1800, 18) 5--100 (34--700, 0.3--7) No n/a

214706LH 250 (1800, 18) 5--100 (34--700, 0.3--7) Yes (see 0--100 (0--700, 0--7)

elow)

{

(

)

(

)

(

)

{

(

)

(

)

(

)

{

(

)

(

)

(

)

26C160 {A 250 (1800, 18) 5--100 (34--700, 0.3--7)

(

elow)

0--200 (0--1400, 0--14)

217314LF 250 (1800, 18) 20--160 (140--1100, 1.4--11) Yes 0--300 (0--2100, 0--21)

221118LE 250 (1800, 18) 20--160 (140--1100, 1.4--11) No n/a

{ISO pitch thread inlet and outlet. Not compatible with S standard pitch.

nFluid housing coated with PTFE polymer.

LThese models are and certified.

The fluid supply system’s main line pressures often exceed the pressure range of the gauge supplied

with regulators 214706, 26C160, and 24A082. Exposing this gauge to excessive pressure can damage

the gauge, causing inaccurate readings and the needle will not return to zero.

This damage is not covered y the Graco warranty.

Air Operated Fluid Regulators

Part No. Series Maximum

Regulated

Air Pressure,

psi (kPa, bar)

Maximum Fluid

Inlet Pressure,

psi (kPa, bar)

Regulated Pressure

Range,

psi (kPa, bar)

Gauge Gauge Pressure

Range,

psi (kPa, bar)

214980 }F 30 (210, 2.1) 250 (1800, 18) 0--30 (0--210, 0--2.1) Yes 0--30 (0--210, 0--2.1)

244375 B 100 (700, 7) 250 (1800, 18) 5--100 (34--700, 0.3--7) No n/a

}Regulated air pressures from 30--100 psi (210--690 kPa, 2.1--6.9 bar) may be used if a 100 psi rated gauge is

installed.

4 307212

5307212

WARNING

PRESSURIZED EQUIPMENT HAZARD

Spray from the gun, hose leaks, or ruptured components can splash fluid in the eyes or on the skin

and cause serious injury.

DDo not stop or deflect fluid leaks with your hand, ody, glove, or rag.

DFollow the Pressure Relief Procedure on page 8 whenever you: are instructed to relieve the

pressure; stop spraying; clean, check, or service the equipment; and install or clean the fluid

nozzle.

DTighten all the fluid connections efore operating the equipment.

DCheck the hoses, tu es, and couplings daily. Replace worn, damaged, or loose parts immediately.

Permanently coupled hoses cannot e repaired; replace the entire hose.

INSTRUCTIONS

EQUIPMENT MISUSE HAZARD

Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result

in a serious injury.

DThis equipment is for professional use only.

DRead all the instruction manuals, tags, and la els efore operating the equipment.

DUse the equipment only for its intended purpose. If you are uncertain a out usage, call your Graco

distri utor.

DDo not alter or modify this equipment. Use only genuine Graco parts and accessories.

DCheck the equipment daily. Repair or replace worn or damaged parts immediately.

DDo not exceed the maximum working pressure of the lowest rated system component.

DUse fluids that are compati le with the equipment wetted parts. See the Technical Data section of

all the equipment manuals. Read the fluid manufacturer’s warnings.

DNever use 1,1,1--trichloroethane, methylene chloride, other halogenated hydrocar on solvents, or

fluids containing such solvents in these regulators. In the event that there is a diaphragm failure, a

serious chemical reaction could occur, with the possi ility of explosion.

DRoute the hoses away from traffic areas, sharp edges, moving parts, and hot surfaces. Do not

expose Graco hoses to temperatures a ove 180_F (82_C) or elow --40_F (--40_C).

DNever kink or over end the hoses or use the hoses to pull equipment.

DComply with all applica le local, state, and national fire, electrical, and other safety

regulations.

6 307212

Installation

FLUID SUPPLY

INLET BALL VALVE

OUTLET BALL VALVE

PIPE NIPPLES

BACK

PRESSURE

VALVE

FLUID RETURN

AIR FILTER

& REGULATOR

Spring Operated Installation

Models 214895, 214706, 217314,

221118, and 24A082

Pilot Regulator Air Supply Line

Air Operated Installation

Model 214980 shown

OUTLET BALL VALVE

AIR SUPPLY

AIR FILTER

MOISTURE SEPARATOR

& REGULATORS

INLET BALL VALVE

Fig. 1

Fig. 2

AIR REGULATOR

BYPASS VALVE

FLUID REGULATOR

7307212

Installation

Fluid pressure regulators are used for accurate, posi-

tive control of the fluid pressure to spray guns, dis-

pensing valves or atomizing heads.

Regulators installed at circulating line take-offs or

pumps are used to reduce main line pressure and

maintain the desired fluid pressure to the spray gun or

atomizing head.

Before Installing the Fluid Regulator

1. Determine where to locate the regulator.

2. Install a all valve for the regulator inlet and outlet.

3. Install temporary plum ing etween the all

valves.

4. Thoroughly flush the system to remove metal

chips and other contaminants and to check for

leaks.

Installing the Fluid Regulator

1. Remove the temporary plum ing and install one

regulator for each spray gun. See the Dimension-

al Dra ing on page 21 for regulator dimensions.

Mount the regulator in a vertical position, as shown

in Figs. 1 and 2, for the est flow and minimum

pigment settling. The gauge, if used, must e

mounted vertically. If the regulator is mounted

horizontally, an el ow must e used so the gauge

will e vertical.

2. Put sealer on threaded connections, except on the

swiveling end of swivel unions as it interferes with

the swivel action.

3. Flush and test the entire system. Be sure to follow

the flushing procedure on page 8.

8 307212

Operation

DThe new system must e cleaned and tested

thoroughly efore admitting fluid to the regulator

to avoid contaminants clogging or damaging the

regulator.

DAlways use the lowest possi le air and fluid

pressures for your application. High pressures

cause premature spray nozzle and pump wear.

NOTE: Reference num ers and letters in parentheses

in the text refer to the Figs. and Parts Drawing.

Pressure Relief Procedure

WARNING

PRESSURIZED EQUIPMENT HAZARD

Read warnings, page 5.

1. Shut off the pump.

2. Close the fluid regulator’s inlet all valve. Refer to

Figs. 1 and 2.

3. Relieve fluid pressure in the fluid regulator y

triggering the spray gun.

Flushing Procedure

DFlush efore changing colors, efore fluid can dry in

the equipment, at the end of the day, efore storing,

and efore repairing equipment.

DFlush at the lowest pressure possi le. Check

connectors for leaks and tighten as necessary.

DFlush with a fluid that is compati le with the fluid

eing dispensed and the equipment wetted parts.

1. Record the pressure adjustment setting of the fluid

regulator efore flushing.

2. Shut off the pump and relieve fluid pressure in the

system y triggering the gun and opening the ack

pressure regulator or other ypass valve.

3. Never exceed the maximum working pressure of

the lowest rated system component. Remove the

gauge if the flushing pressure will exceed the

gauge range.

4. Open the fluid regulator fully.

a. Spring Operated Regulators Only (see Fig. 3).

The regulator can e fully opened in two ways:

DUsing the male end (B) of the regulator

key (24), turn the socket--head adjustment

screw (19) fully counterclockwise. The

pressure setting will e retained.

DUsing the female end (A) of the regulator

key (24), turn the adjustment screw (12)

fully clockwise. You will have to reset

pressure after flushing.

. Air Operated Regulator Only. The regulator

can e fully opened in two ways:

DClose the outlet valve at the air regulator

and open the air regulator ypass valve, to

supply air directly to the fluid regulator; do

not exceed the maximum rated air pres-

sure of the fluid regulator. Pressure setting

of the fluid regulator will e retained using

this method.

DIncrease the air regulator setting to fully

open the fluid regulator. You will have to

reset the fluid regulator’s pressure setting

after flushing.

5. Supply solvent to the system. Set pump to the

lowest possi le pressure, and start pump.

6. Flush until thoroughly clean.

9307212

Operation

7. Adjust the fluid regulator to the desired setting.

a. Spring Operated Regulators Only (see Fig. 3).

The regulator can e adjusted in two ways:

DUsing the male end (B) of the regulator

key (24), turn the socket--head adjustment

screw (19) fully clockwise. Verify that the

pressure setting has not changed.

DUsing the female end (A) of the regulator

key (24), turn the adjustment screw (12)

counterclockwise to return to the desired

pressure setting.

. Air Operated Regulator Only. The regulator

can e adjusted in two ways:

DClose the air regulator ypass valve and

open the outlet valve at the air regulator.

Verify that the pressure setting has not

changed.

DAdjust the air regulator to return to the

desired fluid pressure setting.

Regulating Fluid Pressure

Spring Operated Regulator

1. Close the regulator: engage the female end (A) of

the key (24) with the adjusting screw (12) and turn

it counterclockwise to relieve the spring tension.

See Fig. 3.

2. Start the pump and open the fluid regulator’s inlet

all valve to admit fluid to the regulator. See Fig. 1.

3. Turn the key (24) clockwise to increase fluid pres-

sure. See Fig. 3. Adjust for the desired spray

pattern.

NOTE: If using a fluid pressure gauge, reduce the

regulator pressure efore partially relieving pressure in

the gun hose, to ensure a correct gauge reading. Then

increase regulator pressure to the desired setting.

Air Operated Regulator

1. Start the pump and open the fluid regulator’s inlet

all valve to admit fluid to the regulator. See Fig. 2.

2. Increase the air pressure to o tain the desired fluid

pressure. Adjust for the desired spray pattern.

NOTE: If using a fluid pressure gauge, reduce the

regulator pressure efore partially relieving pressure in

the gun hose, to ensure a correct gauge reading. Then

increase regulator pressure to the desired setting.

NOTE: Make sure the air leed hole in the air line

fitting (29) is not plugged. Refer to page 12.

For the est results, use an air regulator with at least a

2 in. (51 mm) diameter diaphragm to control this fluid

regulator.

Fig. 3

10 307212

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Controller Handbücher

Graco

Graco 217314 Bedienungsanleitung

Graco

Graco 15J753 Bedienungsanleitung

Graco

Graco ProMix 2KS Betriebsanleitung

Graco

Graco 24N468 Bedienungsanleitung

Graco

Graco 214706 Bedienungsanleitung

Graco

Graco PrecisionFlo XL Bedienungsanleitung

Graco

Graco GLC 2200 Bedienungsanleitung

Graco

Graco 257528 Bedienungsanleitung

Graco

Graco Series A Bedienungsanleitung

Graco

Graco 24G621 Stücklistenhandbuch

Graco

Graco InvisiPac HM25 Gebrauchs- und Pflegehandbuch

Graco

Graco BDS Bedienungsanleitung

Graco

Graco G Series Bedienungsanleitung

Graco

Graco Series B Bedienungsanleitung

Graco

Graco Series A Stücklistenhandbuch

Graco

Graco 24H002 A Series Bedienungsanleitung

Graco

Graco 24E025 Bedienungsanleitung

Graco

Graco Series A Stücklistenhandbuch

Graco

Graco SERIES F Bedienungsanleitung

Graco

Graco Trabon LC-1000 Bedienungsanleitung

Graco

Graco ProBell Stücklistenhandbuch

Graco

Graco LC0250 Stücklistenhandbuch

Graco

Graco ProBell 24Z221 Stücklistenhandbuch

Graco

Graco 114-459 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch