Graco InvisiPac Bedienungsanleitung
Read instruction manual 334784 for complete
instructions and warnings. This Quick Guide is not
a substitute for reading and understanding all
instructions manuals and warnings labels
supplied with the equipment.
Turn System
On
Screen Navigation
Turn System
Off
Integrated Systems
Stand-Alone Systems
Select
Program
1. Arrow left _ __to
navigate to the “PC
Control” screen.
2. Enter the screen ___
and arrow up or
down _ __. Press
___ to select a pro-
gram.
Clear
Errors
Acknowledge errors by
pressing _ __ once for
each error.
Display will show “No
Active Errors” unless
error was unable to
clear. Seek technical
support if any error
persists.
- or -
EN
335007B
Quick Guide
InvisiPac®Pattern Controller
1
335007
Wiring Installation
Integrated InvisiPac Systems
• Use melter System Enable
instead of this one
• Use this Disable to hold
guns from dispensing with-
out shutting off the heat.
Power
RED
BLACK
GRN/YL
PLC Inputs
0-30 VDC
Bi-polar
Isolated
Alarm Outputs
0-30 VDC or 0-240 VAC
Dry contact output
No alarm: closed
Alarm: open
Valves (Guns)
24 VDC
1A max each
Triggers
24 VDC
NPN, PNP, Dry Contact
Encoders
15 VDC
Line driver (RS422)
Differential A/B signals
(Z is not used)
NOTE: Swap A with B to
reverse direction
Run Ups
24 VDC
I/P or V/P
Enable
Rising edge enables
Falling edge disables
Disable
Pull high to disable
Program Select
4 bits, 15 programs
(0000 is unused)
EXAMPLE:
1010 into 3,2,1,0
Selects program 10
LINE 1 ALARM
LINE 2 ALARM
CAN
COMMUNICATION
BROWN
BLACK
BLUE
WHITE
BROWN
BLACK
BLUE
WHITE
RED
BROWN
WHITE
YELLOW
GREEN
BLUE
BARE
BARE
BLUE
GREEN
YELLOW
WHITE
BROWN
RED
BROWN
BLK or WH
BLUE
BLUE
BLK or WH
BROWN
Dial Settings
0 - Integrated
1 - Stand-alone
Mini DIN
BLUE
BROWN
DIN “I”
BLACK
BLACK
2335007
Line
Mode 2.
No Encoder
• Check time based or dis-
tance mode.
• Un-check encoder box
(PC-8e only) _ _ ._.
• Set fixed speed ___ to
adjust last measured
product length_ _.
Encoder (PC-8e only)
• Un-check time based
mode.
• Check encoder box_ __.
• Set pulses per mm_ __to
adjust last measured
product length_ _.
• Set low line speed advi-
sory level__ _.
Trigger
Setup 3. • Set trigger polarity _ _. Indicators show on __or off __.
• Assign to line 1 or 2 (PC-8e only) ___ .
General 4.
No Run Up
• Disable pressure com-
pensation.
• Enable or disable modu-
lated bead (PC-8e only).
Run Up (PC-8e only)
• Enable pressure
compensation.
Gun (Valve)
Setup 5.
Set gun open___and- ---close compensation
• ~5ms for high speed guns
• ~10ms for standard guns
NOTE: Applies to high speed lines requiring precise beads.
Run Up
Control 6.
Set Modulated Bead Curve
• Set output value ___ at
line speed___ .
• Set max and min _ _ .
Set Run Up Curve
• Set output value _ _ at
line speed___ .
• Set max and min _ _ .
PC Setup Screens
1. Event Map 2. Line Mode
3. Trigger Setup 4. General
5. Gun (Valve) Setup 6. Run Up Control
3335007
Select
Program
Select and Name Programs
1. Enter page ___ to select program to edit.
2. Name program ___ .
3. Copy ___ or delete ___ program.
Tips
• Copy existing to start new programs
• Make backup copies before editing
Enter Event
Map
Set Up Even Map
1. Assign triggers to valve __.
2. Set gun-to-trigger offset _ ___ .
3. Set minimum box length (optional) ___.
4. Enable or disable pattern mirroring___ .
5. Set stitch savings ___ and interval _ __.
Define
Pattern
Enter Bead Information
1. Enter page___ ,use arrows _ __and
press enter ___ to edit beads.
2. Offset from start of product__ _ .
3. Length of bead _ ___.
4. Stitched or not ___.
NOTE: Stitch option not shown when sav-
ings on Event Map is set to 0%.
5. Confirm changes ___.
Preview Pattern
• See which beads are solid or stitched
• View endpoint of last bead on each gun
• View trigger assignment (red if none)
4335007B, May 2017, Original instructions. This manual contains English. MM 335007.
Andere Graco Controller Handbücher
Graco
Graco 217314 Bedienungsanleitung
Graco
Graco H Series Bedienungsanleitung
Graco
Graco Matrix PAC 247436 Bedienungsanleitung
Graco
Graco 114-459 Bedienungsanleitung
Graco
Graco 3A7639A Bedienungsanleitung
Graco
Graco 311595C Stücklistenhandbuch
Graco
Graco BDS Bedienungsanleitung
Graco
Graco Harrier EZ-Batch Bedienungsanleitung
Graco
Graco ProMix 2KS Betriebsanleitung
Graco
Graco Series B Bedienungsanleitung
Graco
Graco 24G621 Stücklistenhandbuch
Graco
Graco GLC 4400 Bedienungsanleitung
Graco
Graco 237160 Bedienungsanleitung
Graco
Graco 214706 Bedienungsanleitung
Graco
Graco Series B Bedienungsanleitung
Graco
Graco IPH-25 Series Leitfaden
Graco
Graco 289208 Bedienungsanleitung
Graco
Graco G Series Bedienungsanleitung
Graco
Graco ProBell Electrostatic Controller Stücklistenhandbuch
Graco
Graco 214895 Bedienungsanleitung
