Graco SaniSpray HP ProPack 25T780 Gebrauchs- und Pflegehandbuch

3A8304B

For use with Graco SaniSpray HP 20 Cordless and HP 20 Electrostatic Handheld

sprayers. For portable spraying of water-based disinfectants approved for spray

application only. Not for use with architectural paints and coatings. Not approved for use

in explosive atmospheres or hazardous (classified) locations. For professional use only.

Important Safety Instructions

Read all warnings and instructions in this manual, in the sprayer

manual, and on the sprayer and ProPack before using the

equipment. Be familiar with the controls and the proper usage

of the equipment. Save these instructions.

Important Medical Information

Read the medical alert card provided with the sprayer. It

contains injection injury treatment information for a doctor.

Keep it with you when operating the equipment.

Operation, Repair, Parts

SaniSpray HP™ProPack

Backpack Kit 25T780

Use only genuine Graco replacement parts.

The use of non-Graco replacement parts may void warranty.

WARNING

CHEMICAL HAZARD

To prevent serious injury:

•Follow all directions and

requirements on disinfectant

label. It is a violation of Federal

law to use an EPA-approved

disinfectant in a manner

inconsistent with its labeling.

•Flush after each use. Never

store disinfectant in

equipment.

•Use only with appropriate

personal protective

equipment.

www.graco.com/techsupport

?? ??

www.graco.com/sanisprayhp20esupport

Contents

23A8304B

Contents

Know Your ProPack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Start Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Pressure Relief Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Starting a New Job . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Backpack Strap Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 6

How to Spray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Refilling ProPack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Cleanup and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cleaning Sprayer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Cleaning ProPack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Parts List - SaniSpray HP ProPack . . . . . . . . . . . . . . . . . . . 11

Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Recycling and Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

End of Product Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

California Proposition 65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Graco Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Graco Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Related Manuals

Manuals can also be found at www.graco.com

3A7649 SaniSpray HP 20 Cordless

3A8070 SaniSpray HP 20 Electrostatic

Know Your ProPack

3A8304B 3

Know Your ProPack

A ProPack Tank

BLid

C Backpack Strap

D Sprayer Adapter

E Valve Handle

FHose

G Guard

H ProPack Filter

Start Up

43A8304B

Start Up

Pressure Relief Procedure

Follow the Pressure Relief

Procedure whenever you see this

symbol.

1. Remove battery from the sprayer.

2. Turn Prime Knob on the sprayer

downward to PRIME position to relieve

pressure.

Starting a New Job

Refer to disinfectant label for manufacturer's

directions on proper use. If dilution is

required, properly dilute disinfectant.

If you are using the sprayer for the very first

time, see Flushing a New Sprayer in your

sprayer manual.

1. Perform Pressure Relief Procedure,

page 4.

NOTE: If using a SaniSpray HP 20

Electrostatic sprayer, verify Electrostatic

Charge Power Switch is in the OFF position.

2. Turn Valve Handle clockwise to closed

position.

3. Verify ProPack Filter is in ProPack Tank.

Fill ProPack Tank with properly prepared

disinfectant.

NOTE: Fluid level must be above the Hose

connection on the ProPack Tank.

This sprayer builds up an internal pressure

of 1000 psi (6.9 MPa, 68.9 bar) during use.

To help prevent serious injury from

pressurized fluid, such as skin injection

and splashing fluid, follow the Pressure

Relief Procedure whenever you stop

spraying and before cleaning, checking,

servicing, or transporting equipment. Read

all warnings in sprayer manual.

Start Up

3A8304B 5

4. Prime the ProPack as follows:

a. Hold ProPack Adapter and Hose

below ProPack Tank. Point into

waste bucket.

NOTE: Hose cannot be over shoulder or

hooked through backpack strap during

priming process.

b. Turn Valve Handle

counter-clockwise to open position.

c. Allow fluid to flow from Sprayer

Adapter for 5 seconds.

d. Turn Valve Handle clockwise to

closed position.

5. Remove Pump Filter from sprayer.

6. Connect ProPack to sprayer as follows:

a. Align Valve Handle with Prime

Knob on sprayer.

b. Push Sprayer Adapter onto the

sprayer. Twist to lock.

NOTICE

It is necessary to prime the Hose with liquid

to run the sprayer. Do not run the sprayer

dry, it will cause damage to the pump.

Start Up

63A8304B

7. Prime the pump with disinfectant as

follows:

a. Verify Prime Knob on sprayer is

pointed down to PRIME position.

b. Install a fully charged battery into

the sprayer.

c. Set Speed Control on sprayer to

10.

d. Turn Valve Handle

counter-clockwise to open position.

e. Verify Spray Tip is forward in the

SPRAY position. Turn Prime Knob

on sprayer forward to SPRAY

position.

f. Turn sprayer upside down. Pull the

trigger and spray for 5 seconds. If

sprayer does not spray within 5

seconds, STOP and repeat

Starting a New Job, page 4.

NOTE: Sprayer must spray disinfectant for 5

seconds to be primed before proceeding to

step 8.

8. You are now ready to spray!

Backpack Strap

Adjustment

For best results, make strap adjustments

while wearing ProPack full of disinfectant.

ProPack should fit comfortably on lower

back, and still allow enough free movement to

easily operate equipment.

NOTICE

Do not run sprayer without fluid. Running

the sprayer dry will cause damage to the

pump.

How to Spray

3A8304B 7

How to Spray

Review How to Spray in your sprayer

manual. Read all warnings and instructions in

your sprayer manual and on the sprayer.

NOTE: If using a SaniSpray HP 20

Electrostatic sprayer, turn Electrostatic

Charge Power Switch to ON position before

starting to spray. When the trigger is pulled,

the electrostatic light will illuminate. Review

Grounding instructions in your sprayer

manual.

If sprayer does not spray, try the steps

below:

•Repeat Starting a New Job, page 4, to

prime ProPack and sprayer.

•Disinfectant in ProPack may be low.

Remaining fluid can be transferred to a

42 ounce cup assembly, or ProPack can

be refilled. To refill the ProPack Tank,

follow Refilling ProPack, page 7.

•Make certain the Spray Tip is not

clogged. See Clear Tip Clogs in your

sprayer manual.

•If sprayer still does not spray, see

Troubleshooting, page 10.

Refilling ProPack

1. If using a SaniSpray HP 20 Electrostatic

sprayer, turn the Electrostatic Charge

Power Switch to the OFF position.

2. Perform Pressure Relief Procedure,

page 4.

3. Turn Valve Handle clockwise to closed

position.

4. Remove Sprayer Adapter from sprayer.

Set sprayer on a rag to capture any

disinfectant that may drip.

5. Separate Lid from ProPack Tank.

6. Follow steps 2 – 7 in Starting a New

Job, page 4.

CHEMICAL REACTION HAZARD

Mixing disinfectants can result in a violent

chemical reaction, potentially causing

serious chemical burns. Always completely

clean ProPack and Hose before changing to

a different disinfectant.

Cleanup and Storage

83A8304B

Cleanup and Storage

Cleaning Sprayer

Cleaning your sprayer with warm water is

required after each use to remove

disinfectant and residues.

1. Perform Pressure Relief Procedure,

page 4.

2. Turn Valve Handle clockwise to closed

position.

3. Remove Sprayer Adapter from sprayer.

Set sprayer on a rag to capture any

disinfectant that may drip.

4. Follow instructions for Cleanup and

Storage in your sprayer manual.

Cleaning ProPack

At the end of each day's use, clean your

ProPack with warm water to remove all

disinfectant and residue.

1. Verify Valve Handle is in closed position.

2. Separate Lid from ProPack Tank.

Remove Filter from ProPack Tank.

3. Pour excess disinfectant into waste

bucket.

NOTICE

Disinfectant left in sprayer will damage the

sprayer. To avoid damage, always

completely flush with warm water after

every use. Do not store sprayer with

disinfectant in it.

Cleanup and Storage

3A8304B 9

4. Install ProPack Filter and fill ProPack

Tank with warm water.

5. Flush water through ProPack as follows:

a. Hold Sprayer Adapter below

ProPack Tank. Point into waste

bucket.

b. Turn Valve Handle

counter-clockwise to open position.

c. Allow all water to drain from

ProPack Tank and Hose.

6. Pour any excess water from ProPack

Tank into waste bucket.

7. Verify all fluid is drained from Hose. Turn

Valve Handle clockwise to closed

position.

8. Dispose of the fluid in the waste bucket

according to instructions on the

disinfectant container label and

applicable regulations.

9. Use a soft cloth moistened with water to

clean and wipe disinfectant from outside

of the ProPack.

Storage

•Do not allow water to freeze in ProPack

or Hose.

•Store ProPack in upright position.

•Store ProPack indoors in a cool, dry

place.

•Review Storage in your sprayer manual

for further instructions.

Troubleshooting

10 3A8304B

Troubleshooting

Remove battery from sprayer and relieve

pressure before disassembling or repairing.

See Pressure Relief Procedure, page 4.

Sprayer Diagnostics

www.graco.com/techsupport

?? ??

Problem Cause Solution

Fluid does not flow from

Sprayer Adapter

Valve Handle is closed. Open Valve Handle.

ProPack is not primed. Repeat Starting a New Job,

page 4. Verify Sprayer Adapter

and Hose are held below the

ProPack tank. Hose cannot be

over shoulder or hooked through

backpack strap.

Low fluid level in ProPack Tank. Add more fluid to ProPack Tank.

Sprayer and ProPack will lose

prime when fluid level is near 32

oz (1 liter).

Sprayer makes sound but

no fluid is sprayed when

trigger is pulled.

Sprayer is not primed. Prime ProPack and sprayer.

See Starting a New Job, page

4. Verify the following:

•Fluid level is above outlet

fitting (more than

approximately 32 oz (1 liter).

•No air is in hose.

•Valve Handle is open.

Prime Knob on sprayer is in PRIME

position.

Turn Prime Knob to SPRAY

position.

Spray Tip is not in SPRAY position. Turn Spray Tip to SPRAY

position.

Speed Control on sprayer is set too

low.

Increase speed until sprayer

sprays.

Sprayer Pump has reached end of

life.

Replace Pump Assembly. See

Sprayer manual.

Sprayer makes no sound

when trigger is pulled.

No battery or low battery voltage. Install fully charged battery.

Problem with sprayer. See Troubleshooting in sprayer

manual.

Fluid leaking from Hose

near Guard

Loose nut on tank fitting, not

compressing gasket.

Tighten nut from inside of

ProPack Tank.

Replace Hose Assembly. See

Parts, page 11.

Strap will not clip onto

ProPack Tank.

Clip on Backpack Strap is damaged

or broken. Replace Backpack Strap. See

Parts, page 11.

Inhaltsverzeichnis

Andere Graco Spritzpistole Handbücher

Graco

Graco GM3000 Bedienungsanleitung

Graco

Graco Ultra Max II 695 Bedienungsanleitung

Graco

Graco TX 65 Bedienungsanleitung

Graco

Graco 308692N Bedienungsanleitung

Graco

Graco AA 2000 Datenblatt

Graco

Graco Fire-Ball A Series Bedienungsanleitung

Graco

Graco 231-033 Bedienungsanleitung

Graco

Graco 223–390 Bedienungsanleitung

Graco

Graco FinishPro II 295 Gebrauchs- und Pflegehandbuch

Graco

Graco 222-340 Bedienungsanleitung

Graco

Graco DURON Performance 390 Betriebsanleitung

Graco

Graco GMAX II 3900 Premium Handbuch

Graco

Graco GM 3000 Bedienungsanleitung

Graco

Graco 980 Bedienungsanleitung

Graco

Graco T-Max 405 A Series Betriebsanleitung

Graco

Graco HYDRA-SPRAY EM 400 Bedienungsanleitung

Graco

Graco Mark V B Series Bedienungsanleitung

Graco

Graco BLACK MAX Bedienungsanleitung

Graco

Graco 16N664 Gebrauchs- und Pflegehandbuch

Graco

Graco 695 Premium Hi Bedienungsanleitung

Graco

Graco 288629 Bedienungsanleitung

Graco

Graco RentalPro 230PC Bedienungsanleitung

Graco

Graco Reactor 3 E-XP1 Standard Bedienungsanleitung

Graco

Graco 243238 Bedienungsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung

WAGNER

WAGNER W 125 Bedienungsanleitung

My Clean Buddy

My Clean Buddy PW018 Bedienungsanleitung

HAZET-WERK

HAZET-WERK Hazet 9045 P-1 Bedienungsanleitung