Graco T-MAX 506 Handbuch

T-MAX™506/657

www.graco.com

START-UP

STAR-TUP Spray WITH Air <= 1.5 mm

Fill product hopper

with pre-mixed texture

product.

Turn pressure control

knob until steady stream

flows from product tube. Turn pump OFF.

Turn applicator OFF.

Turn ON/OFF switch

to ON.

Loosen nut on bottom

of pump

2-3 turns to

release pressure.

Turn pressure control to

maximum. To spray, aim

applicator at wall from

0.5 m distance wall and

open applicator.

To clean clogged tip, turn

applicator OFF, turn tip 180° to

CLEAN position, aim towards free

area, turn applicator ON. When

clog clears, turn applicator OFF

and tip to SPRAY postion.

Turn pressure

control off (0).

Aim applicator into

hopper.

Turn applicator ON.

DO NOT USE WITH

QUICK-SET MATERIALS

Pressure Relief

DO NOT USE WITH

QUICK-SET MATERIALS

Pressure

Relief

Use different

tip nozzle size

to adjust flow.

Install filter and tip

extension.

Connect applicator

to product tube.

Add water if thinning is

required. Mix thoroughly.

HDA531

HDA535

HDA541

HDA545

HDA651

HDA661

HDA671

mc03 m

Spray WITHOUT Air < .25 mm

Screw tip assembly

onto applicator.

Fill product hopper with

mixed texture product.

Place product tube into hopper, turn ON/OFF switch to ON.

Turn control knob to ‘green’ section and allow material to product 30 sec.

Turn pump control knob to

shut pump off.

Screw air hose and valve to applicator.

Connect product tube to gun.

Turn applicator valve OFF.

Insert air nozzle.

Hold applicator over

product hopper and turn

applicator ON.

Turn air compressor ON. Turn pump

control knob to ‘green’ section to

achieve desired product flow rate.

Regulate air valve for

proper atomization.

To stop spraying,

turn applicator OFF.

Quick Operator’s Guide

SET-UP

This procedure is for water-based paints and flushing agents. For solvent-based paints and flushing agents (i.e. mineral spirits), you must first

read the section on Fire and Explosion Hazards in the Operating Instructions. Please note this Quick Guide is at no means replacing the official

Graco manual. Graco can at no means be liable for any consequences of not following the safety regulations as stipulated in the official manual.

* Please check the Graco operations manual supplied with the unit for more details.

WARNING

Turn pump control off (0).

Plug electrical cord into grounded outlet.Connect pump module to hopper cart.

Remove pump plug.

Connect product tube to pump outlet.

PRESSURE RELEASE PROCESS

Turn pump control knob counter-clockwise,

to shut off pump.

Close applicator after pressure release.

Close air valve.

Scrape remaining product in

hopper into pump to be pumped

from sprayer.

Rotate pump control to

(0) to shut pump off.

Shut air compressor OFF if spraying with air.

Remove applicator from product tube.

Clean applicator.

Turn pump control

clockwise to start pump.

Turn pump control to (0) to

shut pump OFF.

Clean applicator, spray tips and

guard with brush.Set ON/OFF switch to OFF.

Turn pump control

clockwise to pump

unused texture product

out of product hopper

and tube.

Run pump until

cleaning ball exits

product hose.

Retrieve cleaning

ball. Repeat till water

comes out clear.

Insert moistened cleaning ball into pump.

Connect product tube to pump outlet.

Clean hardened product

from applicator nozzles

with air nozzle cleaner.

Remove drain plug from hopper.

Clean hopper with water, brush

and sponge. Insert drain plug.

Fill hopper with 1/3clear water.

GRACO DISTRIBUTION BVBA Industrieterrein Oude Bunders

Slakweidestraat 31 • B-3630 Maasmechelen

Tel: +32 (89) 770 700 • Fax: +32 (89) 770 777

www.graco.com

Graco is certified ISO 9001.

All information, illustrations, and specifications in this document are based on the latest product information available at the time of publication.

The right is reserved to make changes at any time without notice. For more information on Graco’s intellectual property, see www.graco.com/patent or www.graco.com/trademarks.

CHOOSE THE RIGHT TIP (HDA-XXX)

CLEAN-UP

XTRA LIGHT LIGHT MEDIUM HEAVY

HDA531 HDA541 HDA651 HDA671

HDA535 HDA545 HDA661 -

VERY FINE - 3 MM FINE - 4 MM MEDIUM - 6 MM MEDIUM HEAVY - 8 MM HEAVY - 10 MM

248888 248524 248525 248526 248527

Andere Handbücher für T-MAX 506

Dieses Handbuch passt für folgende Modelle

Andere Graco Spritzpistole Handbücher

Graco

Graco Magnum TexFinish 246186 Bedienungsanleitung

Graco

Graco 24F150 Stücklistenhandbuch

Graco

Graco M73109 A Series Bedienungsanleitung

Graco

Graco PerformAA 15 Stücklistenhandbuch

Graco

Graco ULTRA PLUS+ 750 Bedienungsanleitung

Graco

Graco Ultimate Mx795 Bedienungsanleitung

Graco

Graco DT 234140 A Betriebsanleitung

Graco

Graco Series A Bedienungsanleitung

Graco

Graco Glascraft GC-1388G Bedienungsanleitung

Graco

Graco GM5000HD Bedienungsanleitung

Graco

Graco H.E.L.P. 1600 Bedienungsanleitung

Graco

Graco AIRLESSCO SP400 Hi Boy Betriebsanleitung

Graco

Graco 950 Series Stücklistenhandbuch

Graco

Graco Xtreme 244463 Bedienungsanleitung

Graco

Graco 311321H Kurzanleitung

Graco

Graco 245866 Bedienungsanleitung

Graco

Graco TexSpray EXT HP Bedienungsanleitung

Graco

Graco Contractor King 279005 Bedienungsanleitung

Graco

Graco Fusion AP Bedienungsanleitung

Graco

Graco SG20 Stücklistenhandbuch

Graco

Graco 510 Handbuch

Graco

Graco GTX 257030 Bedienungsanleitung

Graco

Graco SG2 Bedienungsanleitung

Graco

Graco ULTIMATE Mx 1095 A Series Bedienungsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

Conrad

Conrad Hobby Airbrush K3 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung

WAGNER

WAGNER W 125 Bedienungsanleitung

My Clean Buddy

My Clean Buddy PW018 Bedienungsanleitung