Graco T-Max Applicator 256383 Gebrauchs- und Pflegehandbuch

312879E

Operation, Repair, Parts

T-Max Applicator

For portable spraying of water-based materials. Can be used for application of

solvent-based materials only when solvent compatible seals are installed and solvent

compatible, conductive hoses are used. For professional use only.

Not approved for use in European explosive atmosphere locations.

Models 256383, 17Z054

1000 psi (6.9 MPa, 69 bar) Maximum Fluid Working Pressure

250 psi (1.7 MPa, 17 bar) Maximum Air Working Pressure

Important Safety Instructions

Read all warnings and instructions in this manual and in

the T-Max operation manual before using the equipment.

Save these instructions.

Related Manuals:

3A6748 T-Max Operation, Repair, Parts

Warnings

2312879E

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The

exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When

these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.

Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual

where applicable.

FIRE AND EXPLOSION HAZARD

Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. Paint or solvent

flowing through the equipment can cause static sparking. To help prevent fire and explosion:

• Use equipment only in well-ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop

cloths (potential static sparking).

• Ground all equipment in the work area.

• Never spray or flush solvent at high pressure.

• Keep work area free of debris, including solvent, rags and gasoline.

• Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are

present.

• Use only grounded hoses.

• Hold gun firmly to side of grounded pail when triggering into pail. Do not use pail liners unless they are

anti-static or conductive.

•Stop operation immediately if static sparking occurs or you feel a shock.Do not use equipment until you

identify and correct the problem.

• Keep a working fire extinguisher in the work area.

SKIN INJECTION HAZARD

High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a

cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.

• Do not spray without tip guard installed.

• Do not point gun at anyone or at any part of the body.

• Do not put your hand over the spray tip.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Follow the Pressure Relief Procedure when you stop spraying and before cleaning, checking, or

servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses and couplings daily. Replace worn or damaged parts immediately.

Warnings

312879E 3

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See Technical Specifications in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Specifications

in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about

your material, request Safety Data Sheets (SDSs) from distributor or retailer.

• Do not leave the work area while equipment is energized or under pressure.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine

manufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and create

safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

PRESSURIZED ALUMINUM PARTS HAZARD

Use of fluids that are incompatible with aluminum in pressurized equipment can cause serious chemical

reaction and equipment rupture. Failure to follow this warning can result in death, serious injury, or property

damage.

• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids

containing such solvents.

• Do not use chlorine bleach.

• Many other fluids may contain chemicals that can react with aluminum. Contact your material supplier for

compatibility.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including eye

injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes but is not limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

Pressure Relief Procedure

4312879E

Pressure Relief Procedure

Follow the Pressure Relief Procedure whenever

you see this symbol.

1. Turn on/off switch OFF and turn pressure control

knob fully counterclockwise to OFF.

2. Point applicator into hopper. Turn applicator ON.

3. If you suspect the spray tip or hose is clogged or

that pressure has not been fully relieved:

a. If installed, turn prime valve down to prime

position.

b. VERY SLOWLY loosen the retaining ring (10),

hose end coupling (43), or pressure relief valve

on the sprayer to relieve pressure gradually.

c. Loosen the nut or coupling completely.

d. Clear the obstruction in the hose or tip.

NOTE: If pressure relief valve was used to relieve

pressure, be sure to disassemble and clean thoroughly.

This equipment stays pressurized until pressure is

manually relieved. To help prevent serious injury from

pressurized fluid, such as skin injection, splashing

fluid and moving parts, follow the Pressure Relief

Procedure when you stop spraying and before

cleaning, checking, or servicing the equipment.

Flush the Equipment (Solvent-Based Materials)

312879E 5

Flush the Equipment

(Solvent-Based Materials)

• Flush before changing materials, before fluid can

dry or cure in the equipment, at the end of the day,

before storing, and before repairing equipment.

• Flush with a fluid that is compatible with the fluid

being dispensed and the equipment wetted parts.

• Flush at the lowest pressure possible. Check con-

nectors for leaks and tighten as necessary.

• Do not leave the applicator or any parts in water or

cleaning solvents.

1. Follow Pressure Relief Procedure, page 4.

2. Remove the spray tip and guard by loosening

retaining ring (10).

3. Hold a metal part of the gun firmly to a grounded

metal pail. Trigger the gun until clean solvent

dispenses.

4. Store in a dry location.

To avoid fire and explosion, always ground equipment

and waste container. To avoid static sparking and

injury from splashing, always flush at the lowest

possible pressure.

Setup

6312879E

Setup

Make sure sprayer is turned OFF and unplugged from power

source. Refer to your sprayer instruction manual for priming

and spray instructions.

Airless Spray Setup

Connect Applicator to Sprayer

1. Attach supply hose to sprayer fluid outlet.

2. Attach other end of supply hose to applicator swivel

(17).

3. Refer to sprayer instruction manual for priming

instructions.

Install Applicator Tip and Guard

1. If equipment has recently been operated, perform

Pressure Relief Procedure, page 4.

2. Using a pencil or similar object, insert seal (20) into

back of guard (18).

3. Install guard (18) onto end of applicator (9).

4. Insert tip (19) in guard (18). Tighten retaining nut.

Air Spray Setup

Connect Applicator to Sprayer

1. Attach supply hose to sprayer fluid outlet.

2. Attach other end of supply hose to applicator swivel

(17).

3. Install air hose to applicator check valve (8).

4. Refer to sprayer instruction manual for priming

instructions.

Install Applicator Air Nozzle

1. If equipment has recently been operated, perform

Pressure Relief Procedure, page 4.

2. Install air nozzle (27; 37d-37g) and retainer (10).

3. Replace retainer with Fine Finish Kit (40) for finer

finishes.

To avoid serious injury from skin injection, do not put

your hand in front of the spray tip when installing or

removing the spray tip and tip guard.

Operation

312879E 7

Operation

Airless Spray

1. Be sure the arrow shaped tip (19) faces forward

(spray).

2. Hold applicator perpendicular and approximately

40 in. (1 m) from surface. Move applicator first, then

open applicator to spray a test pattern.

3. Slowly increase pump pressure until coverage is

uniform and even (see sprayer instruction manual

for additional information).

Aligning Spray

1. Perform Pressure Relief Procedure, page 4.

2. Loosen guard retaining nut.

3. Align guard (18) horizontally to spray a horizontal

pattern.

4. Align guard (18) vertically to spray a vertical pattern.

Clear Tip Clog

To avoid tip clogs:

• When the applicator is not in use for extended

periods of time, keep the tip “wet” and perform

Pressure Relief Procedure, page 4.

• Keep tip clean and free of material.

1. Rotate SwitchTip to unclog position. Aim applicator

at floor and turn applicator ON. When clog clears,

turn applicator OFF.

UNCLOG

2. Rotate SwitchTip back to spray position. Turn

applicator ON. Spray test pattern.

SPRAY

Air Spray

1. Set material flow (see sprayer instruction manual for

additional information).

2. Spray test pattern

3. Turn air knob on and adjust, and/or select another

air nozzle, for desired pattern.

NOTE: Air continues to flow when handle is in off

position to keep material out of air passages.

Cleanup

Flush applicator after each work shift and store in a dry

location. Do not leave the applicator or any parts in

water or cleaning solvents.

(4) Vertical

(3) Horizontal

ti11908a ti11909a

ti11714a

ti11794a

ti11715a

ti11793a

Parts 17Z054

8312879E

Parts 17Z054

Ref Part Description Qty

1 289921

HANDLE, valve, includes 2, 13, 14, 15

2* 15T848 PLATE, stop, valve 1

3* 289916 SPOOL, valve 1

4* 289918 KIT, o-ring and bearing 1

4a BEARING, upper 1

4b O-RING, fluid 2

4c BEARING, lower 1

4d O-RING, air 2

7 124796 O-RING 1

8 289919 KIT, check valve 1

9 15T827 HOUSING, valve 1

10 15T326 RING, retaining, nozzle 1

11 289922 FILTER, screen, texture, 18 mesh,

includes 33

12 15D727 ADAPTER, GHD RAC 1

13 107110 LOCKNUT 2

14 108193 WASHER, plain 2

15 514237 SCREW, cap sch 10-32 x 1 1/2 2

17 17Y920 SWIVEL, assy, texture heavy 1

18 246215 GUARD, RAC X 1

19 HDA651 TIP, spray, RAC X (651) 1

20 246453 KIT, gasket and seat (5 sets) 1

22 15U034 TAG, Tmax handle function 1

30*† 121548 WASHER, plain 1

31*† 121549 RING, retaining, E-ring 1

33 277789 SUPPORT, filter 2

34 15U687 SEAL, adapter, filter, texture 1

35 289923 FILTER, screen, texture, 30 mesh,

includes 33

36* 289917 SEAT, spool, valve, includes 7 1

37 17Z185 KIT, accessories, air assist 1

37a 112779 VALVE, needle 1

37b 156823 FITTING, union, swivel 1

37c 15C899 HOSE, cpld, air, 9.5mm x 15m 1

37d 248524 NOZZLE, 4mm 1

37e 248525 NOZZLE, 6mm 1

37f 248526 NOZZLE, 8mm 1

37g 248527 NOZZLE, 10mm 1

37h 15U027 HOSE, air, cpld 1

37i 169967 FITTING, line air 1

37j 17Y924 NUT, retaining 1

37k 17Z274 ADAPTER, housing 1

37l 24S114 TIP, disk, spray, W4, hardened 1

37m 24S115 TIP, disk, spray, W6, hardened 1

37n 24S116 TIP, disk, spray, W8, hardened 1

37o 24S117 TIP, disk, spray, W10, hardened 1

37p 24S118 TIP, disk, spray, W12, hardened 1

37q 24S119 TIP, disk, spray, WXL, hardened 1

37r 248888 NOZZLE, 3 mm 1

42 15U368 NUT, cap 1

43 289874 COUPLER, female 1

44 15X791 PLUG, air passage 1

* Included in Spool Repair Kit 289916

† Included in O-ring and Bearing Kit 289918

Ref Part Description Qty

Parts 256383

312879E 9

Parts 256383

11,35

17 736

ti11785a

41 42

‡

Ref Part Description Qty

1 289921

HANDLE, valve, includes 2, 13, 14, 15

2* 15T848 PLATE, stop, valve 1

3* 289916 SPOOL, valve 1

4* 289918 KIT, o-ring and bearing 1

4a BEARING, upper 1

4b O-RING, fluid 2

4c BEARING, lower 1

4d O-RING, air 2

7 111027 O-RING 1

8 289919 KIT, check valve 1

9 15T827 HOUSING, valve 1

10 15T326 RING, retaining, nozzle 1

11 289922 FILTER, screen, texture, 18 mesh,

includes 33

12 15D727 ADAPTER, GHD RAC 1

13 107110 LOCKNUT 2

14 108193 WASHER, plain 2

15 514237 SCREW, cap sch 10-32 x 1 1/2 2

17 289920 SWIVEL, assy, texture heavy 1

18 246215 GUARD, RAC X 1

19 HDA651 TIP, spray, RAC X (651) 1

20 246453 KIT, gasket and seat (5 sets) 1

27 248524 NOZZLE, 4 mm, rnd 1

30*† 121548 WASHER, plain 1

31*† 121549 RING, retaining, E-ring 1

33 277789 SUPPORT, filter 2

34 15U687 SEAL, adapter, filter, texture 1

35 289923 FILTER, screen, texture, 30 mesh,

includes 33

36* 289917 SEAT, spool, valve, includes 7 1

40 287227 KIT, Accessory, Tex, Fine Finish 1

41 15U027 HOSE, air, extension 1

42 15U368 NUT, cap 1

* Included in Spool Repair Kit 289916

† Included in O-ring and Bearing Kit 289918

‡ This applicator requires Graco coupler 289874

Ref Part Description Qty

Spool Valve Repair

10 312879E

Spool Valve Repair

Before performing any maintenance on applicator, read

all warnings on front cover of this manual and performd

Pressure Relief Procedure, page 4.

Spool Valve Removal

NOTE: Spool (3) and/or seat (36) may be rotated 180°

for extended life if they are not worn through completely.

1. Remove swivel (17), o-ring (7) and seat (36).

2. Remove nut (13), screw (15), washer (14) and

handle (1). Remove plate (2), clip (31) and washer

(30).

3. Remove spool (3) from housing (9).

Spool Valve Installation

1. Apply grease (supplied with Kits 289916 and

289918) to spool, o-rings and bearings and inside of

housing.

2. Assemble o-rings and bearings onto spool. Align

bearing (4a, 4c) gaps away from ports in housing.

3. Install spool in housing. Secure with washer (30),

and clip (31).

4. Install plate (2) onto spool (note location of

orientation hole). Install handle with screw, washer

and nut.

5. Apply grease to o-ring (7). Install seat (36), o-ring

(7) and swivel (17).

Technical Data

Maximum fluid working pressure 1000 psi (6.9 MPa, 69 bar)

Maximum air working pressure 250 psi (1.7 MPa, 17 bar)

Air Requirements 30 scfm (0.84 m3/min) Maximum

Fluid Inlet Size 1 in.(m) cam and groove (Graco HP)

Air Inlet Size 1/4 npsm(m)

Wetted Parts Aluminum, stainless steel, PE, POM, polyurethane, nitrile, nylon, PVC, tungsten carbide

Weight † 2.9 lb (1,3 kg)

Height 5.8 in. (14,7 cm)

Width 7.0 in. (17,8 cm)

Length † 12.7 in. (32,3 cm)

Sound Data without Air (applicator

only):

Sound Pressure Level 84dB(A)*

Sound Power Level 83dB(A)*

Sound Data with Air (applicator only):

Sound Pressure Level 118dB(A)*

Sound Power Level 118dB(A)*

* Spraying simulated acoustical texture under typical conditions as specified by the material manufacturer.

† Airless configuration

Andere Handbücher für T-Max Applicator 256383

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Spritzpistole Handbücher

Graco

Graco 312145D Bedienungsanleitung

Graco

Graco 231-817 Bedienungsanleitung

Graco

Graco Reactor E-10hp Bedienungsanleitung

Graco

Graco Project Series Bedienungsanleitung

Graco

Graco TurfLiner 826059 Bedienungsanleitung

Graco

Graco 311001G Datenblatt

Graco

Graco 217-38 EM 380 Bedienungsanleitung

Graco

Graco 222625 Bedienungsanleitung

Graco

Graco 190ES 261825 Bedienungsanleitung

Graco

Graco HVLP EDGE II Gebrauchs- und Pflegehandbuch

Graco

Graco XM 24W626 Bedienungsanleitung

Graco

Graco 455st Pro Bedienungsanleitung

Graco

Graco G1200 Bedienungsanleitung

Graco

Graco XM Series Bedienungsanleitung

Graco

Graco HydraSprayr 230975 Bedienungsanleitung

Graco

Graco PT2500 Datenblatt

Graco

Graco Fusion AP Bedienungsanleitung

Graco

Graco GM 5000 Bedienungsanleitung

Graco

Graco RS Betriebsanleitung

Graco

Graco 245924 Leitfaden

Graco

Graco Magnum Pro Plus Series Leitfaden

Graco

Graco TexSpray Compact HP Bedienungsanleitung

Graco

Graco True Airless LTS15 Bedienungsanleitung

Graco

Graco GH 311797J Betriebsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung

WAGNER

WAGNER W 125 Bedienungsanleitung

My Clean Buddy

My Clean Buddy PW018 Bedienungsanleitung

HAZET-WERK

HAZET-WERK Hazet 9045 P-1 Bedienungsanleitung