Graco Ultra Max 309273 Bedienungsanleitung

Ultra Maxt

Electric Airless Sprayers

Operating Instructions

The intent of these instructions is to provide the new painter with a quick and easy reference to

become familiar with airless sprayers. This does not replace the Instruction Manual supplied

with this sprayer. Read and understand the instructions and warnings in that manual.

Important Note: The Graco Standard product line has a wide range of sprayer units that vary

slightly. The basic operations procedures are the same for all sprayers. Some illustrations may

not be applicable to the particular sprayer purchased.

Tools Required:

DTwo adjustable wrenches

DTwo 5 gallon metal pails

DGrounding wires and clamps for pails

DPencil

Suggested proper clothing:

DRespirator

DSafety glasses

309273

Rev. D

How To Perform:

SComponent Identification 3. . . . . . .

SSetup 4. . . . . . . . . . . . . . . . . . . . . . . . . . .

SStartup 7. . . . . . . . . . . . . . . . . . . . . . . . . .

SSMARTCONTROLt9. . . . . . . . . . .

SCleanup 11. . . . . . . . . . . . . . . . . . . . . . . .

STrouble Shooting 15. . . . . . . . . . . . . .

SMaintenance 16. . . . . . . . . . . . . . . . . . .

SStorage 16. . . . . . . . . . . . . . . . . . . . . . . .

STip Wear 16. . . . . . . . . . . . . . . . . . . . . . .

3300 psi (227 bar 22.7 MPa) Maximum Working Pressure

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

Graco Inc. is registered to I.S. EN ISO 9001

2309273

PRESSURE RELIEF – Do this when cleaning, repairing or shuting down sprayer

WASTE

RESÍDUOS

À JETER

DESECHO

1. Turn pressure to lowest setting.

Turn power OFF.

Unplug sprayer.

2. Trigger gun to relieve pressure.

3. Put drain tube in pail.

Turn prime valve down.

WARNING

Fire and explosion hazard: Solvent and paint fumes can

ignite or explode.

To help prevent a fire and explosion:

DUse only in an extremely well ventilated area.

DEliminate all ignition sources; such as pilot lights, cigarettes

and static arcs from plastic drop cloths. Do not plug or

unplug power cords or turn lights on or off in spray area.

DGround Sprayer, object being sprayed, paint and solvent

pails.

DHold gun firmly to side of grounded pail when triggering into

pail.

DUse only conductive airless paint hose.

DDo not use 1,1,1-trichloroethane, methylene chloride, other

halogenated hydrocarbon solvents or fluids containing such

solvents in pressurized aluminum equipment. Such use

could result in a chemical reaction, with the possibility of

explosion.

DTo reduce risk of electric shock, use grounded outlet

only. Shut OFF and unplug when repairing.

Fluid injection and high pressure hazard: High pressure

spray or leaks can inject fluid into the body.

To help prevent injection, always:

DEngage trigger safety latch when not spraying.

DKeep clear of nozzle and leaks.

DNever spray without a tip guard.

DDo PRESSURE RELIEF if you stop spraying or begin

servicing sprayer.

DDo not use components rated less than sprayer Maximum

Working Pressure.

DNever allow children to use this unit.

If high pressure fluid pierces your skin, the injury might

look like “just a cut”. But it is a serious wound! Get immediate

medical attention.

3309273

Power Switch

Pressure Control

Component Identification

Suction Tube

Filter

Prime Valve

Prime/drain position

Paint position

Spray Gun Trigger Safety

Put trigger safety ON

when not spraying.

Take trigger safety OFF

before triggering gun.

Digital Display

(Not available on all models)

15/20A Switch

AutoClean Valve

(Not available on all models)

Use 15A if sprayer

causes circuit

breakers to trip

(1095/1595 only)

Drain Tube

Note:Unclip drain

tube for best filter

drainage

safety OFF

safety ON

Contractor

Contractor II

4309273

1. Connect Graco airless hose to sprayer.

Tighten securely.

2. Connect other end of hose to gun.

Setup

3. Tighten securely.

4. Remove tip guard.

5309273

5. Check inlet strainer for clogs and debris.

6. Fill throat packing nut with TSL to prevent

premature packing wear.

Do this each time you spray.

Approximate Fill Level

6309273

PAINT

FLUSH

7. Turn power OFF.

8. Plug power supply cord into a properly grounded

electrical outlet.

9. Turn prime valve down.

10.Place suction tube and drain tube in grounded

metal pail partially filled with flushing fluid. Attach

ground wire to pail and to true earth ground. Do 1.

–5. of Startup to flush out storage oil shipped in

sprayer. Use water to flush water base paint and

mineral spirits to flush oil base paint and storage

oil.

7309273

FLUSH

Note: Inspect fittings for leaks. Do not stop leaks with your hand or a rag! If leaks

occur, do Pressure Relief. Tighten leaky fittings. Repeat Startup, 1. – 5. If no

leaks, continue to trigger gun until system is thoroughly flushed. Proceed to 6.

Startup

15 SEC

1. Turn prime valve down.

Turn pressure control to lowest pressure.

2. Turn power ON.

3. Increase pressure enough to start motor

and allow fluid to circulate for 15 sec-

onds; turn pressure down, turn prime

valve horizontal.

4. Take spray gun trigger safety OFF.

5. Hold gun against grounded metal

flushing pail. Trigger gun and increase

fluid pressure slowly until pump runs

smoothly.

safety OFF ContractorContractor II

8309273

FLUSH

PAINT

General Surfaces Tip Recommendations Chart

Wood Interior Cab-

inets, Paneling

Interior Walls or Ceilings

Drywall, Plaster

Over Hang

Surfaces Materials Filter

Mesh 6–8 8–10 10–12 12–14 Orifice

Size (in.)

Fan Width (in.)

at 12 in.

Masonry

Block, Stucco, Concrete

Wood Exterior

Shingle, Siding, Shiplap

Open Joist and Ceiling

Areas

Stain, Sanding

Sealer, Lacquer,

Varnish, Shellac

100

.011

Latex, Vinyl, Acrylic

Primers, Enamels

Latex, Vinyl, Acrylic,

Oil Base Alkyds

Exterior Stains,

Latex, Vinyl, Acrylic

Mil White, Hi Builds

.015

.017

.019

.015

.017

.019

.017

.019

.021

.017

.019

.021

.019

.021

.023

.013

6. Place siphon tube in paint pail.

7. Trigger gun again into flushing fluid pail until

paint appears. Assemble tip and guard, page 8.

9309273

SwitchTip and Guard Assembly

1. Insert SwitchTip.

Insert seat and OneSeal.

2. Screw assembly onto gun. Hand tighten.

SwitchTip

OneSeal

seat

Press SMARTCONTROL button to cycle through

PRESSURE – GAL/LTR – TIMER displays

DPRESSURE: Fluid pressure at the sprayer

DGAL/LTR: Accumulated total of gallons/liters sprayed

DTIMER: Duration of AutoClean flush cycle

NOTE: The SMARTCONTROL button is not

active if pressure is above 200 psi

Operation

Error Codes

Sprayer stops and displays error code if fault

occurs

After fault has been corrected or Timer

reaches zero, turn sprayer OFF and then

ON to reset SMARTCONTROL

High pressure limit

Pressure transducer fault

Line voltage too high

Too much current

Motor overheated

Pressure > 2000 psi while in Flush Timer Mode

Line voltage too low

Pressure is below 200 psi

Digital display switches are not set

* Models not equipped with digital displays:

Error codes are displayed inside SMART-

CONTROL. Refer to Manual 309255 for in-

structions.

SMARTCONTROLt

(Not available on all models*)

10 309273

Spray Test Pattern

heavy

edges

Clearing Tip Clogs

1. Trigger gun and spray test pattern.

Slowly adjust pressure to eliminate

heavy edges. Use smaller tip size if

pressure adjustment can not eliminate

heavy edges.

2. Hold gun perpendicular, 10–12 in.

(25–30 cm) from surface. Spray back

and forth. Use strokes overlapped by

50%. Start gun movement before trig-

gering gun and release trigger before

stopping gun movement.

1. Release trigger, put trigger safety ON.

Rotate SwitchTip. Take trigger safety

OFF and trigger gun to clear the clog.

Never point gun towards your hand

or into a rag!

2. Put trigger safety ON, return SwitchTip

to original position, take trigger safety

OFF and continue spraying.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Spritzpistole Handbücher

Graco

Graco Series A Stücklistenhandbuch

Graco

Graco Series D Bedienungsanleitung

Graco

Graco FieldLazer 248942 Bedienungsanleitung

Graco

Graco 231826 Bedienungsanleitung

Graco

Graco M73380 Bedienungsanleitung

Graco

Graco APX 5200 Leitfaden

Graco

Graco MONARK 222-617 Bedienungsanleitung

Graco

Graco GX-7A Bedienungsanleitung

Graco

Graco LineLazer II 3900 Bedienungsanleitung

Graco

Graco BLACK MAX Bedienungsanleitung

Graco

Graco Delta Spray 308741N Bedienungsanleitung

Graco

Graco Delta Spray 7031A Bedienungsanleitung

Graco

Graco Magnum pro finex H5 HV3900VEUG Bedienungsanleitung

Graco

Graco 17R936 Bedienungsanleitung

Graco

Graco RoadLazer RoadPak Bedienungsanleitung

Graco

Graco 220-627 B Series Datenblatt

Graco

Graco 231580 Datenblatt

Graco

Graco Pail Mount Packages Datenblatt

Graco

Graco King E60 Bedienungsanleitung

Graco

Graco 310624E Bedienungsanleitung

Graco

Graco T-Max 405 Bedienungsanleitung

Graco

Graco 3A0243A Betriebsanleitung

Graco

Graco M680 Bedienungsanleitung

Graco

Graco A 218-690 Bedienungsanleitung

Beliebte Spritzpistole Handbücher anderer Marken

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Bedienungsanleitung

Binks

Binks SV100 Bedienungsanleitung

Fimco

Fimco LG-4-3-1 Bedienungsanleitung

AG SPRAY

AG SPRAY FS-ATV-25BL Bedienungsanleitung

Nordson

Nordson MicroMax 2 Bedienungsanleitung

Bonide

Bonide 051 Bedienungsanleitung

zogics

zogics Z-DAS Bedienungsanleitung

KISANKRAFT

KISANKRAFT KK-KBS-165 Bedienungsanleitung

Matrix

Matrix SG 650 Bedienungsanleitung

Anest Iwata

Anest Iwata SGA-3 Kurzanleitung

paasche

paasche VV Datenblatt

Carlisle

Carlisle DeVilbiss JGA-510 Bedienungsanleitung

Gardena

Gardena 11120 Bedienungsanleitung

Conrad

Conrad Hobby Airbrush K3 Bedienungsanleitung

wiwa

wiwa 14025 R/F Bedienungsanleitung

DeVilbiss

DeVilbiss LUNA2i Bedienungsanleitung

WAGNER

WAGNER W 125 Bedienungsanleitung

My Clean Buddy

My Clean Buddy PW018 Bedienungsanleitung