Graco 248113 Bedienungsanleitung
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
Copyright 2003, Graco Inc. is registered to I.S. EN ISO 9001
309930C
Instructions
248113 Transformer
Repair Kit
For Transformers used on Reactor™ Proportioners
Removal
2 309930C
Removal
Use FIG. 1 for the following instruction.
2. Remove Reactor front cover.
3. Remove two bolts holding transformer to frame and
slide forward for access.
4. Disconnect black, plastic, 3-pin connectors going
from back of transformer to circuit board on the left.
There are red wires on one side and black on the
other.
5. Loosen terminal screws one and two at rear of white
terminal block (located at left of transformer wire tap
terminal), and pull out black wires coming from back
of transformer.
6. From the top left of transformer, remove the two
screws and nuts and remove white terminal block.
7. From connector (F), remove and discard clamp (B).
8. From connector (F), remove 8-gauge wire #3 (E).
9. Remove and discard connector (F), wires, and white
terminal block.
10. From connector (G), remove and discard clamp (A).
11. From connector (G), remove all three red wires.
12. Discard connector (G).
WARNING
Repairing this equipment requires access to parts
which may cause electric shock or other serious injury
if work is not performed properly. Read warnings in
Reactor Repair manual. Be sure to shut off all power
to the equipment before repairing.
1. Turn main power OFF . Disconnect power
supply.
WARNING
Wait 5 min for stored voltage to discharge (E-30 and
E-XP2 models only).
FIG. 1: Removing transformer
Discard
To circuit board
To white
terminal block
E
B
A
G
F
Black wires
Red wires
TI5691A
Installation
309930C 3
Installation
Use FIG. 2 for the following instruction.
1. Install 12-gauge red wires #1750 and #1730 into
new connector (J).
2. Once pins are inserted, install clamp to hold pins to
connector.
3. Cut 2 in. off both wires (O, P).
4. Strip 9/16 in. of insulation with 12-gauge wire
stripper.
5. Inspect wires. If not black or in burnt condition,
continue to step 6. If wires appear black or in burnt
condition, repeat steps 3 and 4. Do not exceed 6 in.
7. Install splice onto the strands of each wire. Tighten
screw terminal onto each wire.
9. Slide shrink tubing over splices.
10. Using a heat gun or hair dryer, heat shrink tubing
around splice. If neither is available, wrap entire
length of shrink tubing with electrical tape.
11. Connect 2-pin black plastic connectors together.
FIG. 2: Installation of new harness
H
JK
To white
terminal block
To circuit board
Red wires
TI5690A
6. Install shrink tubing over both wires.
Shrink tubing
Transformer
D
C
8. Insert wires (O, P) into other end of splice and
tighten.
Shrink
tubing
Splice
Transformer
O
P
2-pin black
connector
D
C
Installation
4 309930C
13. Strip 9/16 in. of insulation with 8-gauge wire stripper
from both sides.
14. Inspect wires. If not black or in burnt condition, con-
tinue to step . If wires appear black or in burnt condi-
tion, repeat step 13. Do not exceed 6 in.
17. Slide shrink tube over splice.
18. Using a heat gun or hair dryer, heat shrink tubing
around splice. If neither is available, wrap entire
length of shrink tubing with electrical tape.
19. Slide transformer back and install bolts to bottom.
20. Replace Reactor front panel.
12. Take larger 8-gauge wires and cut pins from both
sides.
15. Install shrink tube over one end.
Wire Cut wire Male pin
Wire
Cut wire
Female pin
Shrink tubing Wire
Wire
16. Install splice between the two wires and tighten
screws.
Wire
Shrink Splice Wire
tubing
Installation
309930C 5
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
This manual contains English. MM 309930
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
www.graco.com
309930C 8/2003, Revised 12/2006
Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material
and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by
Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be
defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance
of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
Graco Phone Numbers
TO PLACE AN ORDER, contact your Graco distributor, or call this number to identify the distributor closest to you:
1-800-328-0211 Toll Free
612-623-6921
612-378-3505 Fax
Inhaltsverzeichnis
Andere Graco Transformator Handbücher
Beliebte Transformator Handbücher anderer Marken
Delta Electronics
Delta Electronics Current Sense Transformers TCE1906H Bedienungsanleitung
Hobart
Hobart 6T28-600CL Bedienungsanleitung
Shinkawa
Shinkawa LS Series Bedienungsanleitung
Huawei
Huawei JUPITER-3000K-H1 Bedienungsanleitung
Monacor
Monacor IMG STAGELINE LTR-102 Bedienungsanleitung
Lionel
Lionel ZW Bedienungsanleitung
