Grafenthal USV PTR-6000 Anleitung zur Verwendung

Service-Handbuch

GRAFENTHAL

USV PTR-6000

GRAFENTHAL GmbH • von-Monschaw-Straße 3 • 47574 Goch • [email protected] • www.grafenthal.de

CONTENT

1. GENERAL INFORMATION .......................................................................................................................................4

1.1 GETTING START........................................................................................................................................................4

1.2 IMPORTANT SAFETY INSTRUCTIONS ........................................................................................................................4

2. ELECTRIC SPECIFICATIONS..................................................................................................................................5

3. FUNCTIONAL BLOCK...............................................................................................................................................7

4. WORKING PRINCIPLE OF THE MAJOR FUNCTIONAL BLOCK.....................................................................9

4.1 SWITCH POWER SUPPLY .........................................................................................................................................9

4.2 PFC/BOOSTER ........................................................................................................................................................9

4.3 INVERTER.................................................................................................................................................................9

4.4 CHARGER...............................................................................................................................................................10

4.5 EMI BOARD............................................................................................................................................................10

5. FUNCTION EXPLANATIONS FOR EACH PCB.................................................................................................. 11

5.1 SPS-CHARGER BOARD (POWER STAGE BOARD)................................................................................................. 11

5.2 CNTLBOARD (CONTROL BOARD).........................................................................................................................11

5.3 COMMUNICATION BOARD .......................................................................................................................................11

5.4 EMI BOARD............................................................................................................................................................ 11

5.5 MAIN POWER BOARD ............................................................................................................................................. 11

5.6 PARA(A)AND PARA(B) BOARD............................................................................................................................... 11

5.7 O/PRELAY BOARD.................................................................................................................................................12

6. INTERFACE...............................................................................................................................................................13

6.1 LED DISPLAY.........................................................................................................................................................13

6.2 LCD DISPLAY.........................................................................................................................................................13

6.3 LCD DISPLAY ICON................................................................................................................................................13

7. TROUBLE SHOOTING............................................................................................................................................16

7.1 LCD PANEL DISPLAY PATTERN DEFINITION ..........................................................................................................16

7.1.1 Trouble shooting for warning icon in LCD display.........................................................................................16

7.1.2 Trouble shooting for fault codes in LCD display.............................................................................................17

7.1.3 Trouble shooting..............................................................................................................................................18

7.2 REPAIR ...................................................................................................................................................................18

7.2.1 Basic Instruments and tools.............................................................................................................................19

7.2.2 Configuration of the Model Port on the Control Board ..................................................................................19

7.2.3 Configuration of the charger current on the charger Board ...........................................................................19

7.2.4 Configuration of the

charge voltage

on the charger Board...........................................................................19

7.2.5 Regulation of the system..................................................................................................................................20

7.2.6 Quick Start.......................................................................................................................................................21

8. TEST STEP................................................................................................................................................................23

9. APPENDIX .................................................................................................................................................................24

9.1 REFERENCE WAVEFORM .......................................................................................................................................24

9.2 BASIC COMMUNICATION COMMAND........................................................................................................................26

9.2.1 QGS.................................................................................................................................................................26

9.2.2 V<n>...............................................................................................................................................................27

9.2.3 V±<n>.............................................................................................................................................................27

9.2.4 BUSP±<n>......................................................................................................................................................27

9. 2.5 BUSN±<n> ....................................................................................................................................................28

9. 2.6 VB±<n> .........................................................................................................................................................28

9.2.7 QVFW..............................................................................................................................................................28

9.2.8 OC±<n>..........................................................................................................................................................28

1. General Information

1.1 Getting start

This manual is for Galleon II 6K(L)/10K(L) tower UPS. It can help service person perform the basic

maintenance and repair service.

This manual only focuses on the service section, so you should get the basic operation of the UPS from

the user manual, and make sure you had read and understood the user manual before reading the

manual.

The manual include 9 sections:

●General Information, this section shows you the general information of the service manual.

●Electric Specifications, this section shows you the basic electric specification of the UPS.

●Functional block, this section shows you the major functional block of the UPS.

●Working Principle of the Major Functional Block, this section shows you the working principle of

the major functional block.

● Function explanations for each PCB, this section explains you all the PCBs of the UPS system.

●Interface, this section shows you the LCD interface, including display and setting.

● Trouble Shooting, this section gives you the way to find the problems.

● Test Step, this section tells you how to test the UPS after you repair the unit.

● Appendix, this section shows you the basic waveforms for reference and the basic communication

commands.

1.2 Important Safety Instructions

For qualified service person only.

DO NOT perform any internal service or adjustment of this product unless the technical person is

well trained and experienced. .

Dangerous voltage exists at several points in this product. To avoid personal injury, don't touch

any exposed connections or components while UPS is on.

Turn off the UPS and switch off the input breaker before removing protective case.

AC voltage is always present if the input AC power is still available.

High voltage may exist at DC capacitors. Before removing the protective case, wait for at least

five minutes after turning off the UPS.

Verify input source (voltage and frequency) is within the maximum range before service.

2. Electric Specifications

MODEL

SPECIFICATION

6KL

10K

10KL

Input

Input Voltage

176～300 VAC @ Full Load

110 VAC @ Half Load

Input Frequency

46～54 Hz for 50Hz system

56～64 Hz for 60Hz system

Input Power Factor

≥0.99

Input THD

<4%

Generator

Support

Output

Output Power (VA/Watt)

6000/6000( 20 pieces battery)

10000/10000( 20 pieces battery)

6000/5400( 18~19 pieces battery)

10000/9000(18~19 pieces battery)

6000/4800(16~17 pieces battery)

10000/8000(16~17 pieces battery)

Nominal Output Voltage

208/220/230/240VAC

Voltage Regulation

±1%

Output Frequency

Follows Bypass Frequency in Line Mode

(50/60+0.1) Hz in Battery Mode

Voltage Distortion

≤6% @ Full Nonlinear Load

≤2% @ Full Linear Load

Current Crest Ratio

3:1

Transfer Time

0ms @ Line  Battery

0ms @ Inverter  Bypass

<10ms @ Inverter  ECO

Short Circuit Protection

Yes

Battery

Nominal Battery Voltage

240 VDC

Nominal Battery Quantity

20 pcs

Acceptable Battery Quantity

18~20 pcs

Type/Capacity

12V/7.2Ah

12V/9Ah

Backup Time

≥6minutes@full load

≥4minutes@full load

Efficiency

To Line Mode

>93%

To Battery Mode

>91%

To ECO Mode

>96%

Overload Protection

100%～110%

Alarm and Transfer To Bypass after 10min @ Line mode

Alarm and Cut Off Output after 30s @ Battery mode

110%～130%

Alarm and Transfer To Bypass after 1min @ Line mode

Alarm and Cut Off Output after 10s @ Battery mode

Over 130%

Alarm and Transfer To Bypass after 1s @ Line mode

Alarm and Cut Off Output after 1s @ Battery mode

Alarm and Cut Off Output after 1min @ Bypass mode

Auto Retransfer

Yes

Interface

RS232

Yes

USB 1.1

Yes

EPO

Yes

Environment

OperatingTemperature

0 ℃to 40℃

Humidity

<95% (No condensing)

Acoustic Noise

≤55dB

≤58dB

Standard

ESD

IEC 61000-4-2 Level 4

IEC 61000-4-3 Level 3

EFT

IEC 61000-4-4 Level 4

Surge

IEC 61000-4-5 Level 4

Conduction

IEC/EN 62040-2 Category C3

Radiation

Safety

IEC62040-1-1

Drop

ASTM D5276-94

Vibration

ASTM D4728-87

Mechanical

Inlet

Terminal Block

Outlet

Terminal Block and Receptacle

3. Functional Block

As a true online UPS, the product applies a double conversion topology, comprising functional blocks as

shown in Figure 3.1

Figure 3.1 Function block Diagram

The CNTL block controls the action of the UPS system. It also provides the communication interface for

receiving and executing command from users via the panel or other communication protocol. When the

UPS becomes abnormal, in most case, the CNTL can provide basic information indicating the status of

the UPS.

The Rectifier and PFC blocks are the input stage of the UPS. The blocks convert AC input power into

two stable DC power stored in the BUS capacitor. In the meantime, PFC (Power Factor Correction) will

be executed and allows input current tracking the input voltage waveform. Therefore, the input power

factor will be corrected to 1 to achieve maximum efficiency and produce lowest power pollution to the

utility.

The PFC block in battery mode, also called Booster, is used to convert the low voltage DC power to

higher voltage with stable DC power, stored in the BUS capacitor.

The Inverter block is the output stage of the UPS and used to convert DC power from the BUS capacitor

to sine waveform output power.

When the utility is within the acceptable range, the UPS will provide power directly from the utility input

and the Rectifier and PFC will be executed at the same time.When the utility is outside of the acceptable

range, no matter it’s because of input voltage or input frequency, the UPS will shut down the Rectifier

and PFC functions and turn on the Battery Booster. In case of sudden interruption from input utility, the

controller can detect the interruption in very short time. During the short interval of detecting the

interruption, the output power will be provided by the power stored in the BUS capacitor. In this way,

there is no any interruption on output power.

The charger charges the battery when the UPS system is in online model. You can set the current from

1A to 4A by changing the jumper. And you also can choose a different voltage corresponding to different

battery pieces by changing the jumper on the CNTL board and the charger board.

The Input EMI section provides EMI filter function. The input EMI filters can prevent the UPS from being

interference by external electronic/magnetic noise which is generated by other electronic system and

prevent other systems from the noise generated inside the UPS system.

The SPS generates DC power supply needed by operation of the circuit of the UPS itself. The Bypass

provides a path that utility can power the output directly when the Inverter is not executed. The

Maintenance Bypass provides another path that utility can power the output directly when UPS is in

maintenance status.

4. Working Principle of the Major Functional Block

4.1 Switch Power Supply

The Switch Power Supply (SPS) supplies DC power for UPS operation. The input source of the SPS is

the grid when the grid voltage is higher than 110V . Or the input source of the SPS is the battery.

Figure 4.1 Basic circuit of power supply

Figure 4.1 is a flyback converter. When Q1 is on, all rectifier diodes (D1/D2/D3) are on open status and

all output capacitors (C1/C2/C3) supply currents to the load. The primary coil of the transformer will

become a pure inductor and the primary current will linearly increase to store energy in the coil. When

Q1 is off, primary current will stop and all rectifier diodes (D1/D2/D3) will turn to “close”status. It will

release the stored energy from the primary coil of the transformer to the secondary coil to supply loads.

At the same time, it will charge output capacitors including 15V, +12V, +5V, +12V(Fan), and HFPW.

The power of 12V, +5V supplies stable voltage to all kinds of ICs and other devices such as HCT. The

+12V (Fan) is supplied to fans and relays. The HFPWsupplies a high frequency power for the switch

(SCR/IGBT) driver and some other drive boards.

4.2 PFC/Booster

UBUS+

UBUS-

Utility

Battery

Figure 4.2 PFC/Booster

As shown in the Figure 4.2, when Q1/Q2 is on and D1/D2 is off, the current will increase to store energy

in choke(L1/L2). When the Q1/Q2 is off and D1/D2 is on, the choke will release energy. Therefore, we

can control the current in chokes (input current) by regulating the time of Q1/Q2 on and off.

4.3 Inverter

The input of the three level inverter topology is two DC voltages, and the output is an AC voltage, as

shown in the Figure 4.3. When Q1/Q2 is on and Q/Q3 is off, the voltage of the bridge midpoint is +BUS.

When Q1/Q2 is off and Q3/Q4 is on, the voltage of the midpoint bridge is –BUS. We can get any voltage

waveform between ±BUS voltage from LC filter output by regulating the duty cycle of Q1/Q2/Q3/Q4,

including sine wave form.

Figure 4.3 Three level inverter bridge

4.4 Charger

The function of charger is to charge and maintain the batteries at fully charged condition. The charger

charges the batteries with a constant current at initial stage. At the same time, the battery voltage keeps

increasing until reaching the constant charge voltage point. Then, the charge current will decrease

accordingly, now it’s in second stage. After one hour of constant voltage charging, the charge voltage will

change to floating charge voltage, in general, the charger will control the output voltage at a constant

level (13.65V±1% per battery) to optimize battery recharge time and prolong the lifetime of batteries

without overcharging.

Figure 4.4 Topology of the charger

Note: There are two kinds of chargers for standard model UPS and long-run model UPS. They both

apply the same principle, but there is on difference in charger output capacity.

4.5 EMI Board

Input EMI board is connected between utility and the input of rectifier.

Input Output

Common

Choke

Figure 4.5 Topology of the EMI

Inhaltsverzeichnis

Andere Grafenthal UPS Handbücher

Grafenthal

Grafenthal PR-1000 Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung