GRAUPNER S2007 Ultra DC Quad Bedienungsanleitung

OPERATING INSTRUCTION

Prior to use, please read this manual thoroughly.

Keep this manual in a convenient place for quick and easy reference.

• BEFORE USE

• SUPPROT AND SERVICE

Customer support

Internet sales site

A/S regulation

Warranty regulation

• OPENHOBBY A/S CENTER

• SAFETY PRECAUTIONS

• BOX CONTENTS

• SPECIFICATION

• FEATURES

• CHARGER CONTROL IDENTIFICATION

• POWER SOURCE

• BATTERY CONNECTION

• BATTERY TYPE SELECTION

• MEMORY SETUP

• NiCd, NiMH BATTERIES CHARGE/DISCHARGE

NiCd, NiMH charge

NiCd, NiMH discharge

NiCd, NiMH cycle

• The temperature setup for NiCd, NiMH when charge/discharge

• LiPo, LiIon, LiFe BATTERIES CHARGE/DISCHARGE

LiPo charge

LiPo discharge

LiPo cycle

LiPo store

LiPo balancer

The temperature setup for LiPo when charge/discharge

• Pb BATTERY CHARGE/DISCHARGE

Pb charge

Pb discharge

• DISPLAYS DURING CHARGE/DISCHARGE

• ERROR MESSAGES

• BATTERY CHARGE TIME CALCULATION

• NEW BATTERY CHARGE

• Pb BATTERY SAFETY

• LiIon, LiPo, LiFe BATTREIES SAFETY

• ENVIRONMENT PROTECTION NOTES

• SAFETY APPROVAL

9~10P

10P

10~11P

11P

12P

13P

13~14P

14P

14~15P

15P

15~16P

16P

17P

18P

18~19P

19P

Contents

◎ BEFORE USE

Thank you for purchasing ULTRA DC QUAD Charger.

This system is extremely versatile and may be used by beginners and pros alike. In

order for you to make the best use of your system and to y safely, please read this

manual carefully. If you have any difculties while using your system, please consult the

manual, our online Frequently Asked Questions (on the web pages referenced below),

your hobby dealer, or the Graupner/SJ Service Center.

Due to unforeseen changes in production procedures, the information contained in this

manual is subject to change without notice.

◎ SUPPORT AND SERVICE

◎ OPENHOBBY A/S CENTER

Internet sales site

Warranty regulation

Please feel free to contact “www.openhobbby.com” to stay up to date the latest

Graupner/SJ Firmware and the newest product line up.

Refer the WARRANTY CARD in a Package.

Graupner/SJ USA (OPENHOBBY LLC)

Phone : +1 855-5-RCisHoTT (+1 855-572-4746)

E - mail : service@openhobby.com

3245 University Ave, Suite 1520, San Diego, CA 92104

Customer support

Please feel free to ask any question by e-mail or phone. We’ve been trying to deal

with your question. We are open from nine to six, Monday to Friday in Korea. We may

respond to your question by e-mail as soon as possible when we are close.

A/S regulation

Only when the product is faulty after normal operation within the warranty period, we

will repair the product for free based on our regulations. The repair will be paid for by

the consumer when the damage is due to use in improper ways or beyond the warranty

period.

◎ BOX CONTENTS

◎ SAFETY PRECAUTIONS

1. Do not attempt to charge incompatible types of rechargeable batteries. This charger is

designed to only charge and discharge Nickel Cadmium, Nickel Metal Hydride, Lithium

Ion, Lithium Polymer, and Lead Acid batteries.

2. Do not attempt to charge a dead or damaged battery.

3. 12V input from Pb battery or reliable 12V power supplier that can supply more than 7A

current is needed

4. Make sure to place the charger on a rm level surface for charging.

5. Do not attempt to charge batteries at excessive fast charge currents. Check with your

battery manufacturer for the maximum charge rate applicable to your battery.

6. Do not allow water, moisture or foreign objects into the charger and use in a well ven-

tilated area

7. Do not place the battery or charger on or near a ammable object while in use. Keep

away from carpets, cluttered workbenches, etc.

8. Do not leave the charger unattended while charging. Disconnect the battery and

remove input power from charger immediately if the charger becomes hot and keep

the charger and battery cool down before reconnecting. Young children should be

supervised to ensure that they use the appliance safely

9. Do not disassemble the charger.

10. If lead-acid battery is used to charge battery, the battery terminal shouldn’t be con

tacted to the chassis

11. Do not use automotive type battery chargers to power the charger.

12. Do not cover the air intake holes on the charger as this could cause the charger to

overheat.

13. Connect the input leads to a 12V power supply rst, then connect the battery.

14. Do not attempt to charge non-rechargeable batteries.

15. Please comply with LiIon, LiPo, LiFe safety before charging

16. Do not use the damaged AC Power cord.

1. Charger 1EA

2. Temp Sensor 2EA

3. DC input cable 1EA

4. Alligator Clip 1 Set (RED/BK)

5. Charge Cable 1Set (RED/BK)

6. Balance board & cable 4EA

DC 11.0 - 15.0V

1-14Cells(NiCd/NiMH) 1-6Cells(LiPo/LiIon/LiFe) 1-6Cells(Pb batt)/4CH

100mAh ~ 9900mAh NiCd NiMH

100mAh ~ 50000mAh adjustable ONLY for Lilon, LiPo and LiFe

0.1A - 7A in 100mA steps(Max 80W) / 4CH

0.1A - 1.0A in 100mA steps (auto limited to 5W maximum) / 4CH

0 ~ 200mA / 4CH

Max 280mA / 4CH

3mV - 25mV(NiCd/NiMH) per cell

Charge to Discharge / Discharge to Charge

2-line, 16 Black & White backlit character LCD / 4CH

10 / 4CH

220.5 x 170.0 x 40.1 mm / 8.67 x 6.69 x 1.58 in

1012g / 35.70 oz

Input Voltage

Battery Type & Cell

Battery Capacity

Charge Current

Discharge Current

Trickle Charge

Balancing Current

Delta Peak

Cycling

Display Type

Memory

Dimensions

Weight

1. Built in micro processor controls charge/ discharge, storage, balance system

2. NiCd, NiMH, LiIon, LiPo, LiFe, Pb batteries are available. Max 80W charge

3. NiCd and NiMH: Delta peak detection system, Lithium and Pb: Voltage detection

system

4. 2-line, 16 blue backlit character LCD, 4Channels, 10 memories per channel

5. Selectable 3.6V or 3.7V or 3.3V, 1~6 cells LiIon battery

6. Support 0.1A~7.0A charge current, NiCd / NiMH 1-14cells, 1.2-16.8V

7. Support 10~1000mA discharge current, NiCd / NiMH 1-14cells, 1.2-16.8V

8. Support cycle mode (Charge to discharge / Discharge to charge).

9. Prevent form reverse connecting of Input, output terminal. Built in cell balancer

10. DC 12V input.

◎ SPECIFICATION

◎ FEATURES

2x16 character LCD

DC Input

- Output

DC lnput

+ Output

Temp port

Balancing port

Buttons

+ Output

- Output

Balancer port

Temperature

sensor port

◎ CHARGER CONTROL IDENTIFICATION

1. Connect charger to 12V DC power supply

2. Connect the charge cable to OUT PUT terminal in the charger and battery, you need

to double check the polarity( Red +, Black - ) and the input voltage. If the input voltage

is below 11V or above 15V, the charger will show “BATTERY VOLTAGE ERROR” mes-

sage.

◎ POWER SOURCE

Nixx

LiFe

LiPo

Lilon

Lithium batteries need to balance for more safety, if lithium batteries are

charged without balance board, the balancing of lithium batteries is not performed.

CAUTION

◎ BATTERY CONNECTION

Connect charge cable to 4mm output banana sockets on charger with attention to polarity, red

+, black –. If battery is not connected to charger correctly, the error message is appeared

- No battery : When a battery is not connected to the charger’s output

- Open circuit : When a battery becomes disconnected during an operation

- Reverse polarity : When a battery is connected to the output in reverse

When the power supplier is connected to the charger the below screen is displayed and the

Setup screen is displayed after about 1 second

◎ BATTERY TYPE SELECTION

Press BATT TYPE button twice to select Battery type

※ The programming setup is applied differently when you press START/STOP button

less than 1 Sec and longer than 1 Sec

Press ENTER button then battery type blinks and press ENTER button again then

other value blinks. If you leave it for more than 3 sec without operating, the blinking is

stopped. Press and hold ENTER button to start charge or discharge.

ULTRA DC QUAD

Graupner/SJ 1.00

Pole

LiPo

Pole

Nixx

Pole

LiPo

Pole

LiFe

Pole

Lilo

Pole

12V

[01]

800

[01]

3000

[01]

3000

[01]

3000

[01]

3000

[01]

pack

◎ MEMORY SETUP

ULTRA DC QUAD has 4 channels, 10 memories per channel

It is used to store specic battery, charge, discharge and safety parameters, as well as

being used to initiate charging, discharging, cycling/store mode functions.

① Press ENTER BUTTON then the memory number blinks. Press INC/DEC buttons to

select the memory number

② Press ENTER button then BATTERY TYPE blinks. Press INC/DEC buttons to select

battery type.

④ Press ENTER button and INC/DEC buttons to set battery capacity.

③ Press ENTER button then battery cell blinks. Press INC/DEC buttons to set battery cell.

⑤ Press ENTER button to remove the curser blinking.

⑥ Press INC/DEC buttons to set charge current and charge voltage and then press ENTER

button to remove the curser blinking.

⑦ Press INC button to access to DISCHARGE mode and press INC/DEC buttons to set

discharge current and discharge voltage and then press ENTER button to remove the

curser blinking.

Pole

LiPo

Pole

LiPo

Pole

LiPo

Pole

LiPo

Pole

LiPo

C=3.0A

[01]

3000

[01]

3000

[01]

3000

[01]

3000

[01]

3000

CHARGE

4.2V/C

LiPo

D=1.0A

DISCHARGE

3.0V/C

⑧ Press INC button to access to CYCLE mode and press INC/DEC button to charge/dis-

charge sequence and repeating number and then press ENTER button to remove the

curser blinking.

⑨ Press INC button to access STORE mode and press INC/DEC buttons to set charge/dis-

charge and then press ENTER button to remove the curser blinking.

⑩ Press INC button to access to BLANCER mode and check if the setup is correct.

⑪

Press INC button to access to TEMPERATURE mode and check if the setup is correct.

◎ NiCd, NiMH BATTERIES CHARGE/DISCHARGE

- NiCd, NiMH charge

① Go to Nixx mode

② Press INC button to access to CHARGE mode

③ Press ENTER button shortly then the value of charge current blinks, press DEC/INC

buttons to set the desired value of charge current.

LiPo

D=3.0A

LiPo

C=3.0A

LiPo

(03)CELL

LiPo

CYCLE D->C1

D=1.0A

STORE

D=1.0A

BALANCER

START

Temperature

40℃

Prole

Nixx 5S

Nixx

C=3.0A

Nixx

C=3.0A

[01]

3000

CHARGE

d=25mV/c

CHARGE

d=25mV/c

④ Press ENTER button then the value of delta peak blinks, press DEC/INC buttons to

set the desired value of delta peak.

⑤ Press and hold ENTER button to start charge battery.

- NiCd, NiMH cycle

① Go to Nixx mode

- NiCd, NiMH discharge

① Go to Nixx mode

② Press INC button twice to access to DISCHARGE mode

③ Press ENTER button shortly then the value of discharge current blinks, press DEC/

INC buttons to set the desired value of discharge current

④ Press ENTER button then the value of discharge cutoff voltage blinks, press DEC/INC

buttons to set the desired value of discharge cutoff voltage

※ We recommend battery cells x 0.9V as the discharge cutoff voltage

⑤ Press and hold ENTER button to start discharge battery

Nixx

C=3.0A

CHARGE

d=25mV/c

BATTERY

PLEASE

CHECK

WAIT....

Prole

Nixx

D=1.0A

Nixx

D=1.0A

Nixx

D=1.0A

BATTERY

PLEASE

[01]

3000

DISCHARGE

0.8V/C

DISCHARGE

0.8V/C

DISCHARGE

0.8V/C

CHECK

WAIT....

Prole

Nixx 5S

[01]

3000

Inhaltsverzeichnis

Andere GRAUPNER Akkuladegerät Handbücher

GRAUPNER

GRAUPNER AUTOMATIC-TURBO-LADER Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRAMAT 8 Bedienungsanleitung

GRAUPNER

GRAUPNER POLARON AC/DC SPORTS Bedienungsanleitung

GRAUPNER

GRAUPNER 6475 Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRAMAT 12 Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRAMAT 12 PLUS POCKET Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRAMAT 17 Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRAMAT 25 Bedienungsanleitung

GRAUPNER

GRAUPNER LIPO BALANCER CHARGER 2-3S Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRA DUO PLUS 60 Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRA DUO PLUS 50 Bedienungsanleitung

GRAUPNER

GRAUPNER LiPo BALANCER CHARGER 3-4S Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRAMAT 18 Bedienungsanleitung

GRAUPNER

GRAUPNER S2003 Bedienungsanleitung

GRAUPNER

GRAUPNER MULTICHARGER 3 Bedienungsanleitung

GRAUPNER

GRAUPNER ultra duo plus 80 Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRAMAT 5 Bedienungsanleitung

GRAUPNER

GRAUPNER MULTILADER 3 Bedienungsanleitung

GRAUPNER

GRAUPNER MINILADER 3 Bedienungsanleitung

GRAUPNER

GRAUPNER Polaron Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRA QUICK 70 Bedienungsanleitung

GRAUPNER

GRAUPNER Polaron EX Bedienungsanleitung

GRAUPNER

GRAUPNER ULTRAMAT 10 Bedienungsanleitung

GRAUPNER

GRAUPNER PB AUTOMATIKLADER Bedienungsanleitung

Beliebte Akkuladegerät Handbücher anderer Marken

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Bedienungsanleitung

Enelion

Enelion Vertica Bedienungsanleitung

RCA

RCA CHU6 Bedienungsanleitung

ANSMANN

ANSMANN ALCT 6/24-10 Bedienungsanleitung

Hitachi

Hitachi UC 18YRSL Fehlerbehebungshandbuch

Olympus

Olympus B-20 LPC Bedienungsanleitung

Exibel

Exibel ZH1708143 Bedienungsanleitung

Lenmar

Lenmar Mach 1 Bedienungsanleitung

CTEK

CTEK MXS 5.0 Bedienungsanleitung

ABB

ABB HT842379 Bedienungsanleitung

Nitecore

Nitecore Superb Charger SC4 Bedienungsanleitung

Renogy

Renogy RBC2125DS-21W Bedienungsanleitung

Braun

Braun BWC02M Bedienungsanleitung

CTEK

CTEK MXS 3.6 Bedienungsanleitung

Black & Decker

Black & Decker BDV090 Bedienungsanleitung

Trinity

Trinity DPD Bedienungsanleitung

Hulkman

Hulkman Sigma 1 Bedienungsanleitung

IKEA

IKEA koppla Bedienungsanleitung