Gree GMV-ND09A/A-TU Bedienungsanleitung

Owner's Manual

Original Instructions

Commercial Air Conditioners

GMV DC Air Handler

Models:

GMV-ND09A/A-T(U)

GMV-ND12A/A-T(U)

GMV-ND18A/A-T(U)

GMV-ND24A/A-T(U)

GMV-ND30A/A-T(U)

GMV-ND36A/A-T(U)

GMV-ND42A/A-T(U)

GMV-ND48A/A-T(U)

GMV-ND54A/A-T(U)

Preface

For correct installation and operation, please read all instructions carefully. Before reading the

instructions, please be aware of the following items:

(1) For the safe operation of this unit, please read and follow the instructions carefully.

(2) During operation, total capacity of indoor units should not exceed the total capacity of

outdoor units. Otherwise, poor effect of cooling or heating may result.

(3) Direct operators or maintainers should well keep this manual.

(4) If this unit fails to operate normally, please contact our service ncenter as soon as possible

and provide the following information:

Content on the nameplate (model No., cooling capacity, production code, ex-factory date).

Malfunction details (before and after the malfunction occurs).

(5) Each unit has been strictly tested and proved to be qualified before ex-factory. In order to

prevent units from being damaged or operating normally because of improper disassembly,

please do not disassemble the unit by yourself. If you need to disassemble and check units,

please contact our service center. We will send specialists to guide the disassembly.

(6) All graphics in this manual is only for your reference. For sales or production reasons, these

graphics are subject to change by manufacturer without prior notice.

User Notice

This appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible for their

safety. Children should be supervised to ensure that they do not play with the appliance.

Correct Disposal of this product

This marking indicates that this product should not be disposed with other

household wastes. To prevent possible harm to the environment or human health

from uncontrolled waste disposal, recycle it responsibly to promote the sustainable

reuse of material resources. To return your used device, please use the return and

collection systems or contact the retailer where the product was purchased. They

can take this product for environmental safe recycling.

Exception Clauses

Manufacturer will bear no responsibilities when personal injury or property loss is caused by the

following reasons:

(1) Damage the product due to improper use or misuse of the product;

(2) Alter, change, maintain or use the product with other equipment without abiding by the instruction manual of

manufacturer;

(3) After verification, the defect of product is directly caused by corrosive gas;

(4) After verification, defects are due to improper operation during transportation of product;

(5) Operate, repair, maintain the unit without abiding by instruction manual or related regulations;

(6) After verification, the problem or dispute is caused by the quality specification or performance of parts and

components that produced by other manufacturers;

(7) The damage is caused by natural calamities, bad using environment or force majeure.

Contents

1 Safety Precautions······················································································ 1

2 Product Introduction····················································································3

2.1 Names of Key Components················································································ 3

2.2 Rated Working Condition··················································································· 3

3 Preparative for Installation··········································································· 4

3.1 Pre-Installation Instruction·················································································· 4

3.2 Important Safety Instructions···············································································4

3.3 Requirements for Communication Line··································································6

3.4 Wiring Requirements·························································································7

4 Installation Instructions··············································································· 8

4.1 Dimension Data······························································································· 8

4.2 Location········································································································· 8

4.3 Piping Work···································································································10

4.4 Condensate Removal······················································································ 10

4.5 Ductwork·······································································································11

4.6 Installation of Wired Controller··········································································· 11

5 Wiring Work······························································································ 11

5.1 Connection of Wire and Patch Board Terminal······················································ 12

5.2 Power Cord Connection··················································································· 13

5.3 Connection of Communication Wire between Indoor Unit and Outdoor Unit (or indoor unit)

························································································································13

5.4 Connect Communication Wire of Wired Controller··················································14

5.5 Illuminate for Connection of Wired Controller and Indoor Units Network······················14

6 Routine Maintenance················································································· 15

6.1 Cleaning of Filter···························································································· 15

6.2 Maintenance before the Seasonal Use································································ 16

6.3 Maintenance after the Seasonal Use···································································16

7 Table of Error Codes for Indoor Unit···························································· 16

8 Troubleshooting························································································ 16

GMV DC Air Handler

1 Safety Precautions

(1) This product can’t be installed at corrosive, inflammable or explosive environment or the place with

special requirements, such as kitchen. Otherwise, it will affect the normal operation or shorten the service

life of the unit, or even cause fire hazard or serious injury. As for above special places, please adopt

special air conditioner with anti-corrosive or anti-explosion function.

(2) Follow this instruction to complete the installation work. Please carefully read this manual before unit

startup and service.

(3) Wire size of power cord should be large enough.The damaged power cord and connection wire should

be replaced by exclusive cable.

(4) After connecting the power cord, please fix the electric box cover properly in order to avoid accident.

(5) Never fail to comply with the nitrogen charge requirements.Charge nitrogen when welding pipes.

(6) Never short-circuit or cancel the pressure switch to prevent unit damage.

(7) Please firstly connect the wired controller before energization, otherwise wired controller can not be

used.

(8) Before using the unit, please check if the piping and wiring are correct to avoid water leakage, refrigerant

leakage, electric shock, or fire etc.

(9) Do not insert fingers or objects into air outlet/inlet grille.

(10) Open the door and window and keep good ventilation in the room to avoid oxygen deficit when the gas/oil

supplied heating equipment is used.

(11) Never start up or shut off the air conditioner by means of directly plug or unplug the power cord.

(12) Turn off the unit after it runs at least five minutes; otherwise it will influence oil return of the compressor.

(13) Do not allow children operate this unit.

(14) Do not operate this unit with wet hands.

(15) Turn off the unit or cut off the power supply before cleaning the unit, otherwise electric shock or injury

may happen.

(16) Never spray or flush water towards unit, otherwise malfunction or electric shock may happen.

(17) Do not expose the unit to the moist or corrosive circumstances.

(18) Under cooling mode, please don't set the room temperature too low and keep the temperature difference

between indoor and outdoor unit within 5°C (41°F).

(19) User is not allowed to repair the unit. Fault service may cause electric shock or fire accidents. Please

contact Gree appointed service center for help.

(20) Before installation, please check if the power supply is in accordance with the requirements specified on

the nameplate. And also take care of the power safety.

GMV DC Air Handler

(21) Installation should be conducted by dealer or qualified personnel. Please do not attempt to install the unit

by yourself. Improper handling may result in water leakage, electric shock or fire disaster etc.

(22) Be sure to use the exclusive accessory and part to prevent the water leakage, electric shock and fire

accidents.

(23) Make sure the unit can be earthed properly and soundly after plugging into the socket so as to avoid

electric shock. Please do not connect the ground wire to gas pipe, water pipe, lightning rod or telephone

line.

(24) Electrify the unit 8 hours before operation. Please switch on for 8 hours before operation. Do not cut off

the power when 24 hours short-time halting (to protect the compressor).

(25) If refrigerant leakage happens during installation, please ventilate immediately. Poisonous gas will

emerge if the refrigerant gas meets fire.

(26) Volatile liquid like thinner or gasoline will damage the appearance of air conditioner. Please use soft dry

cloth or wet cloth with mild detergent to clean the outer case of air conditioner.

(27) If anything abnormal happens (such as burning smell), please power off the unit and cut off the main

power supply, and then immediately contact Gree appointed service center. If abnormality keeps going,

the unit might be damaged and lead to electric shock or fire.

Any personal injury or property loss caused by improper installation, improper debug, unnecessary

repair or not following the instructions of this manual should not be the responsibility of Gree Electric

Appliances, Inc. of Zhuhai.

GMV DC Air Handler

2 Product Introduction

2.1 Names of Key Components

Fig.2.1

2.2 Rated Working Condition

—

Indoor Side Condition

Outdoor Side Condition

Dry Bulb Temp°C(°F)

Wet Bulb Temp°C(°F)

Dry Bulb Temp°C(°F)

Wet Bulb Temp°C(°F)

Rated Cooling

26.7(80.0)

19.4(67.0)

35(95.0)

23.9(75.0)

Rated Heating

21.1(70.0)

15.6(60.0)

8.3(47.0)

6.1(43.0)

Indoor Unit Working Temperature Range: 16°C (60.8 °F) ~32°C (89.6 °F)

GMV DC Air Handler

3 Preparative for Installation

3.1 Pre-Installation Instruction

3.1.1 Checking Product Received

After receiving the product, please check if there is any damage caused by transportation.

Shipping damage is the responsibility of the carrier. Verify the model No., specifications and

accessories are correct prior to installation. The distributor or manufacturer will not accept claims

from dealers for transportation damage or installation of incorrectly shipped units.

3.1.2 Before Installation

Carefully read all instructions for the installation prior to installing product. Make sure each step

or procedure is understood and any special considerations are taken into account before starting

installation. Assemble all tools, hardware and supplies needed to complete the installation. Some

items may need to be purchased locally. Make sure everything needed to install the product is on

hand before starting.

3.1.3 Codes & Regulations

This product is designed and manufactured to comply with national codes. It is installer’s

responsibilities to install the product in accordance with such codes and/or any prevailing local

codes/regulations. The manufacturer assumes no responsibilities for equipment installed in violation

of any codes or regulations.

3.1.4 Replacement Parts

When reporting shortages or damages, or ordering repair parts, give the complete product No.

and serial numbers as stamped on the product. Replacement parts for this product are available

through your contractor or local distributor.

3.2 Important Safety Instructions

Recognize Safety Symbols, Words, and Labels

The following symbols and labels are used throughout this manual to indicate immediate or

potential hazards. It is the owner’s responsibility to read and comply with all safety information and

instructions accompanying these symbols. Failure to heed safety information increases the risk of

serious personal injury or death, property damage and/or product damage.

Immediate hazards which will result in property damage, product damage,

severe personal injury or death.

Hazards or unsafe practice could result in property damage, product

damage, severe personal injury or death.

Hazards or unsafe practices which may result in property damage, product

damage, severe personal injury or death.

Before serving or installing this equipment. The electrical power to this unit

GMV DC Air Handler

must be in the “off” position. Caution, more than one disconnect may exist. Failure to observe this

warning may result in an electrical shock that can cause personal injury or death.

The United States environmental protection agency (“EPA”) has issued

various regulations regarding the introduction and disposal of refrigerants introduced into this unit.

Failure to follow these regulations may harm the environment and can lead to the imposition of

substantial fines. These regulations may vary due to the passage of laws. A certified technician must

perform the installation and service of this product. Should questions arise, contact your local EPA

office.

Due to high system pressure and electrical shock in potential, installation

and service work can be dangerous. Only trained and qualified personnel are permitted to install or

service this equipment. Observe all warnings contained in this manual and labels/tags attached to the

equipment.

This product is factory shipped for use with a 208-230/1/60 electrical power

supply. This air handler must not be reconfigured to operate with any other power supply.

The unit must have an uninterrupted, unbroken electric grounding to

minimize the possibility of personal injury if an electric fault occurs. The electric grounding circuit may

consist of an appropriate sized power cord which connected with the grounding piece located in the

unit control box and also connecting to the building electric service panel. Other methods of

grounding are permitted if performed in accordance with the “national electric code” (NEC) /

“American national standards institute” (ANSI) / “national fire protection association” (NFPA) 70 and

local/state codes. In Canada, electric grounding conforms to the Canadian electric code CSA c22.1.

Failed to observe this warning can result in electrical shock that can cause personal injury.

Fig.3.2.1

Special warning for installation of furnaces or air handling units in enclosed areas, such

as garages, utility rooms or parking areas.

Carbon monoxide producing devices (such as an automobile, space heater, gas water heater,

etc.) should not be operated in enclosed areas such as unventilated garages, utility rooms or parking

areas because of the danger of carbon monoxide (CO) poisoning resulting from the exhaust

emissions. If a furnace or air handler is installed in an enclosed area such as a garage, utility room or

parking area and a carbon monoxide producing device is operated therein, there must be adequate

GMV DC Air Handler

ventilation directly to outside.

This ventilation is necessary to avoid the danger of CO poisoning which can occur if a carbon

monoxide producing device continues to operate in the enclosed area. Carbon monoxide emission

can be (re)circulated throughout the building if the furnace or air handler is operating in any mode.

CO can cause serious illness including permanent brain damage or death.

3.3 Requirements for Communication Line

If the unit is installed in the place with strong electromagnetic interference, shielded

wire must be applied on the communication wire between indoor unit and wired controller. Twisted

pair line with shielding function must be applied on the communication wire between indoor unit and

indoor unit (outdoor unit).

3.3.1 Select communication line for indoor unit and wired controller

Fig.3.3.1

Wire type

Total length of

communication wire

between indoor unit

and wired controller

Wire size

Wire

standard

Remarks

Light/Ordinary

polyvinyl chloride

sheathed cord.

(UL60335-2011)

L≤250m

(L≤820-1/5ft.)

2×AWG18~

2×AWG16

UL60335-

2011

1. Total length of communication cable can't

exceed 250m (820-1/5ft.).

2. The cord shall be Circular cord (the cores

shall be twisted together).

3. If unit is installed in places with intense

magnetic field or strong interference, it is

necessary to use shielded wire.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Gree Klimaanlage Handbücher

Gree

Gree GFH(09)EA-K3DNA1A/I Bedienungsanleitung

Gree

Gree ForestAir 13-04588 Bedienungsanleitung

Gree

Gree GPC08AH-K3NNC5A Bedienungsanleitung

Gree

Gree GWH07NA-K3NNA4A Bedienungsanleitung

Gree

Gree GISF209BXAE Bedienungsanleitung

Gree

Gree GWH18AC-D3DNA1B Bedienungsanleitung

Gree

Gree U-match Series Bedienungsanleitung

Gree

Gree GMV-N22G/A4A-K Bedienungsanleitung

Gree

Gree GMV-ND24A/A-T Bedienungsanleitung

Gree

Gree GEH09AA-K6DNA1F Bedienungsanleitung

Gree

Gree H2M Bedienungsanleitung

Gree

Gree FP-51XD-E Bedienungsanleitung

Gree

Gree GVC24AMXF-K3NTC7A Bedienungsanleitung

Gree

Gree Soleus Air GM-PAC-12E1 Bedienungsanleitung

Gree

Gree GWC12NC-K3NNA3E Bedienungsanleitung

Gree

Gree GWH09RA-K3DNA1B Bedienungsanleitung

Gree

Gree GWH18RC-K3DBA5E Bedienungsanleitung

Gree

Gree GWHD(18)NK3FO Bedienungsanleitung

Gree

Gree GWC18KG-D3DNA5A Bedienungsanleitung

Gree

Gree NEO09HP230V1AH Bedienungsanleitung

Gree

Gree VERSATI III Series Bedienungsanleitung

Gree

Gree FGR50Pd/DNa-M Bedienungsanleitung

Gree

Gree GSW12-22L/B Betriebsanleitung

Gree

Gree DUCT09HP230V1BD Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung