Gree GWC09AB-D3DNA2D Bedienungsanleitung

Change for Life

Split Air Conditioner

Installation Manual

Residential Air Conditioners

Thank you for choosing Residential Air Conditioners,please read this owner’s

manual carefully before operation and retain it for future reference.

MODEL: GWC09AB-D3DNA2D GWH09AB-D3DNA2D

GWC12AB-D3DNA2DGWH12AB-D3DNA2D

GWC18AC-D3DNA2DGWH18AC-D3DNA2D

GWC24AC-D3DNA2DGWH24AC-D3DNA2D

■ .............................................3

■ ...............................................................4

■ ........................................................1

■ ..............................9

Do not dispose this product as unsorted municipal waste.

Collection of such waste separately for special treatment

is necessary.

CONTENTS

Notices for installation

Installation dimension diagram

Install indoor unit

Test operation and check after installation

■.......................10

Installation and Maintenance of Healthy Filter

Never attempt. Be sure to follow this instruction

The physical product may differ from the drawing in this manual for different display.

If there are some differences between them, please refer to the physical product as

the standard.

This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities or lack of experience and knowledge,

unless they have been given supervision or instruction concerning use of the appliance

by a person responsible for their safety.

Children should be supervised to ensure they are away from the appliance.

■ .............................................................7

Install outdoor unit

Notices for installation

4.Warning:Before obtaining access to terminals, all supply circuits must be disconnected.

5.For appliances with type Y attachment, the instructions shall contain the substance of

the following. If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualified persons in order to avoid a hazard.

6.The appliance must be positioned so that the plug is accessible.

7.The temperature of refrigerant line will be high; please keep the interconnection cable

away from the copper tube.

8. The instructions shall state the substance of the following:

This appliance is not intended for use by persons(including children)with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the appliance by a person responsible

for their safety.

Children should be supervised to ensure that they do not play with the appliance.

Caution

Installation Site Instructions

The unit should be installed only by authorized service center according to local or

government regulations and in compliance with this manual.

Before installing, please contact with local authorized maintenance center. If the unit is

not installed by the authorized service center, the malfunction may not be solved

due to incovenient contact between the user and the service personnel.

When removing the unit to the other place, please firstly contact with the local authorized

service center.

●

Proper installation site is vital for correct and efficient operation of the unit. Avoid the

following sites where:

strong heat sources, vapours, flammable gas or volatile liquids are emitted.

high-frequency electro-magnetic waves are generated by radio equipment,

welders and medical equipment.

salt-laden air prevails (such as close to coastal areas).

the air is contaminated with industrial vapours and oils.

the air contains sulphures gas such as in hot spring zones.

corrosion or poor air quality exists.

Installation Site of Indoor Unit

Select a site where the condensate can be easily drained out, and where it is

easily connected to outdoor unit.

Select a place where the wall is strong enough to withstand the full weight and vibration

of the unit.

Select a place where it is out of reach of children.

The air inlet and outlet should be away from the obstructions. Ensure the air can be

blown through the whole room.

Be sure to leave enough space to allow access for routine maintenance. The installation

site should be 98 3/7 inch or more above the floor．

Notices for installation

Note:

Safety Precautions for Electric Appliances

Installation Site of Outdoor Unit

1.Select a site where noise and outflow air emitted by the unit will not annoy neighbors.

Select a site where there is sufficient ventilation.

Select a site where there is no obstruction blocking the inlet and outlet.

The site should be able to withstand the full weight and vibration.

Select a dry place, but do not expose the unit to direct sunlight or strong wind.

Make sure that the outdoor unit is installed in accordance with the installation instructions,

and is convenient for maintenance and repair.

The height difference between indoor and outdoor units is within16.4ft, and the length of

the connecting tubing does not exceed 32.8ft.

Select a place where it is out of reach of children.

Select a place where the unit does not have negative impact on pedestrians or on the city.

5. The minimum distance between the unit and combustive surface is 4.9ft.

1. A dedicated power supply circuit should be used in accordance with local electrical

safety regulations.

2. Don't drag the power cord with excessive force.

The appliance shall be installed in accordance with national wiring regulations.

An all-pole disconnection switch with a contact separation of at least 9.8ft in all poles

should be connected in fixed wiring.

The unit should be reliably earthed and connected to an exclusive earth device by the

professionals.

4. The air switch must have the functions of magnetic tripping and heat tripping to prevent

short circuit and overload.

Make sure the live wire, neutral wire and earth wire in the family power socket are properly

connected. There should be reliable circuit in the diagram.

Inadequate or incorrect electrical connections may cause electric shock or fire.

●

Make sure that the indoor unit is installed in accordance with installation dimension

Select a place about 3.3ft or more away from TV set or any other electric appliance.

Select a place where the filter can be easily taken out.

instructions.

9. Do not use the unit in the laundry or by swimming pool etc.

Earthing Requirements

①②③

④

1. Air conditioner is type I electric appliance. Please ensure that the unit is reliably earthed.

2. The yellow-green wire in air conditioner is the earthing wire which can not be used

for other purposes. Improper earthing may cause electric shock.

3. The earth resistance should accord to the national criterion.

4. The power must have reliable earthing terminal. Please do not connect the earthing

wire with the following:

W epipsaGepipreta Contamination pipe

Other place that professional personnel consider is unreliable

5. The model and rated values of fuses should accord with the silk print on fuse cover or

PCB.

Installation dimension diagram

Space to the ceiling

Space to the wall

Air outlet side Space to the floor

Above Above

6inch Above 6inch

Above

118

inch 98

6inch

Air inlet side

Air outlet side

Space to the wall

Space to the obstruction

Space to the wall

20inch above

12inch above

79inch above

Installation dimension diagram

● Indoor unit

● Outdoor unit

inch

Drill Piping Hole

1.Slant the piping hole (Ф2 1/6 or Ф2 3/4) on the wall slightly downward

to the outdoor side.

2.Insert the piping-hole sleeve into the hole to prevent the connection piping

and wiring from being damaged when passing through the hole.

Indoor Outdoor

Wall pipe Seal pad

Installation of Indoor Unit

Installation of Mounting Plate

1. Mounting plate should be installed horizontally. As the water tray's outlet for the indoor unit is two-way

type, during installation, the indoor unit should slightly slant to water tray's outlet for smooth drainage of

condensate.

2.Fix the mounting plate on the wall with screws.

3.Be sure that the mounting plate has been fixed firmly enough to withstand about 132.3 lb. Meanwhile, the

weight should be evenly shared by each screw.

Fig.5

09K、

12K UNIT:

(Rear piping hole)(Rear piping hole)

Left Right

the wall

6inch

above

Space to

the wall

6inch

above

Wall Wall

18K UNIT:

24K UNIT:

Ф2 1/6

Ф2 3/4

3 4/7

6 1/6

11 1/7

23 5/6 3 3/4

1/3

33 3/4

1 1/9

4 2/7

Unit:

inch

4 1/3 27 1/3 5 3/5

2 3/4

Ø2 1/6

3 1/7

1 1/6

Ø2 1/6

11 4/5

1/3

37 1/4

6 8/9 27 8 1/5

1 4/7

1 1/4

Ø2 3/4

6 2/5

Ø2 1/6

Connecting Indoor and Outdoor Electric Wires

Installation of Indoor Unit

Note: The insulating tube should be connected reliably with

the sleeve outside the outlet pipe. The drain hose should be

slanted downward slightly, without distortion, bulge or

fluctuation. Do not put the outlet in the water.

bulge distortion

Flooded

●

After tightening the screws, pull the wire slightly to confirm whether it's firm or not.

●

●Make sure that all wiring connections are secure and the cover plates are reinstalled

NOTE:

All wires between indoor and outdoor units must be connected by the qualified electric

contractor.

Electric wires must be connected correctly. Improper connection may cause malfunction.

Tighten the terminal screws securely.

Make sure that the electric connections are earthed properly to prevent electric shock.

properly. Poor installation may cause fire or electric shock.

yellow-

green

brown

Fig.6

1.Open the front panel.

2.Remove the wiring cover as shown in Fig 6.

3.Make the power connection cord and pass through the hole at the back of indoor unit.

4.Reinstall the cord anchorage and wiring cover.

5.Reinstall the front panel.

Wiring cover

outdoor unit connection

Installation of Drain Hose

Connect the drain hose to the outlet pipe of the indoor unit.

Bind the joint with rubber belt.

Put the drain hose into insulating tube.

Wrap the insulating tube with wide rubber belt to prevent

the shift of insulating tube. Slant the drain hose downward

slightly for smooth drainage of condensate.

outlet pipe of

indoor unit

insulating tube

connected

insulating tube

drain hose

outlet pipe of

indoor unit

drain hose

outlet pipe of

indoor unit

outlet pipe of

indoor unit

rubber belt

右后

●

⑴

⑵

Installation of Indoor Unit

The piping can be output from right, right rear, left

or left rear.

When routing the piping and wiring from the left

or right side of indoor unit, cut off the tailings

from the chassis when necessary(As shown in Fig.7)

Cut off tailing 1 when routing the wiring only;

Cut off tailing 1 and tailing 2 when routing

both the wiring and piping.

Take out the piping from body case;wrap the piping,

power cords, drain hose with the tape and then make

them pass through the piping hole. (As shown in Fig.8)

Hang the mounting slots of the indoor unit on the

upper hooks of the mounting plate and check if it is

firm enough. (As shown in Fig.9)

The installation site should be 98 3/7 inch or more

above the floor

Installation of Connection Pipe

Align the center of the pipe flare with the related valve.

Screw in the flare nut by hand and then tighten the

nut with spanner and torque wrench by referring to the

following:

NOTE: Connect the connection pipe to indoor unit at first and then to outdoor unit. Handle pi-

ping bending with care. Do not damage the connection pipe. Ensure that the joint nut

is tightened firmly, otherwise, it may cause leakage.

Spanner Torque

wrench

Piping

Taper nut

Indoor unit piping

Fig.9

Mounting

plate

Fixing hook Mounting

plate

Right

Right rear Fig.8

Left rear

Left

Fig.7

Tailing 1

Tailing 2

Finally wrap it

with tape

Gas side piping

insulation

Water drainage pipe

Liquid side

Piping insulation

Gas side pipingExternal connection

electric wire

Liquid side piping

(N·m)

Ф6.35(1/4”)

Ф9.52(3/8”)

Ф12.7(1/2”)

Ф15.88(5/8”)

34～42N·m(340-420kgf.cm)

14～18N·m(140-180kgf.cm)

49～61N·m(490-610kgf.cm)

68～82N·m(680-820kgf.cm)

Tube diameter Tightening torque,approximate

Installation of Indoor Unit

Remove the handle on the right side plate of outdoor unit.

Take off wire cord anchorage. Connect and fix power cord

to the terminal board. Wiring should fit that of indoor unit.

Fix the power cord with wire clamps and then connect the

the corresponding connector.

Confirm if the wire has been fixed properly.

Reinstall the handle.

●

Installation of Outdoor Unit

Electric Wiring

NOTE:

Incorrect wiring may cause malfunction of spare part.

After the wire has been fixed, ensure there is free

space between the connection and fixing places

on the lead wire.

real product for authentic information.

Wire hole

Sketch map of power connection wire:

Power connection wire Power cord

Cable-cross board

for 9k、12k unit

for 18K、24K unit

Indoor unit

connection

N(1)

2 3 L1

blue black brown

POWER

yellow-

green

blue

brown

yellow-

green

Schematic diagram being reference only, please refer to

● Use vacuum pump

1. Connect the charging hose of manifold valve to charging

port of low-pressure valve. Both high-pressure valve and

low-pressure valve must be tighten up).

2. Connect joint of charging hose to vacuum pump.

3. Fully open Lo （low pressure ）handle of manifold valve

and start the vacuum pump for vacuum pumping.

4. Usually the vacuum pumping time of 2600W AC is about

15min. The vacuum pumping time of 5000W AC is about

20min. The vacuum pumping time of 7200W AC is about

30min. Make sure the pressure is -1.0X105pa (-76cmHg).

When vacuum pumping is finished, close Lo （low pressure ）

handle of manifold valve completely to stop the vacuum pump.

(Note: R410A refrigerant special vacuum pump should be

applied for R410A unit.)

Liquid

valve

Gas valve

Manifold valve

Multimeter

Piezometer

Hi handle

Lo handle

Charging hose Charging hose

Vacuum pump

Length of connection pipeAir purging method

Use vacuum pump

Nameplate value

Refrigerant charging amount

Not longer than 24.6ft

24.6~65.6ft

● Air purging method:

-76cm Hg

Nameplate value +20g/m (for 9k、12k、18k heat pump unit）

Nameplate value +15g/m (for 18k、24k cool only unit）

Nameplate value +50g/m (for 24k

heat pump unit

）

add 15g/20g/50g of refrigerant for additional 1m of pippe length

Air purging

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Gree Klimaanlage Handbücher

Gree

Gree GEH09AA-K6DNA1F Bedienungsanleitung

Gree

Gree GWH12KF-A3DNB1A Handbuch

Gree

Gree GWH12QB-K6DNB8I Bedienungsanleitung

Gree

Gree GMV5 Series Bedienungsanleitung

Gree

Gree Feng Yun Series Bedienungsanleitung

Gree

Gree KFR-25 Bedienungsanleitung

Gree

Gree GWC09QC-A3DNA3D/I Bedienungsanleitung

Gree

Gree GPC12AJ-K3NNA1D Bedienungsanleitung

Gree

Gree GJC07AF Series Bedienungsanleitung

Gree

Gree GMVVQ224WM/C-X Bedienungsanleitung

Gree

Gree GVH24AK-K3DNC6A Bedienungsanleitung

Gree

Gree GWH09AVCXB-K6DNA1B/I Bedienungsanleitung

Gree

Gree G17-5MCVWAC1 Bedienungsanleitung

Gree

Gree FP-34B D-K Series Bedienungsanleitung

Gree

Gree KM09HEDI Bedienungsanleitung

Gree

Gree GMV-ND28T/A-T Bedienungsanleitung

Gree

Gree GWH18TC-S3DBA1E Bedienungsanleitung

Gree

Gree Slim Duct B Series Bedienungsanleitung

Gree

Gree G1407M Bedienungsanleitung

Gree

Gree JKFD5DQS/Na-E Bedienungsanleitung

Gree

Gree BORA GWH12AAB Bedienungsanleitung

Gree

Gree Multi+ Ultra MULTIU18HP230V1DO Betriebsanleitung

Gree

Gree RIO09HP115V1A Bedienungsanleitung

Gree

Gree GMV-ND22T/B-T Bedienungsanleitung

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung