Greenlee AFI-100 Bedienungsanleitung

INSTRUCTION MANUAL

Read and understand all of the instructions and

safety information in this manual before operating or

servicing this tool.

Lea y entienda todas las instrucciones y la información

sobre seguridad que aparecen en este manual, antes de

manejar esta herramienta o darle mantenimiento.

Lire attentivement et bien comprendre toutes les

instructions et les informations sur la sécurité de ce

manuel avant d‘utiliser ou de procéder à l‘entretien de

cet outil.

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

AFI-100

Arc Fault and Ground Fault

Circuit Interrupter Tester

Instrumento de verificación e

interruptor de circuito de falla

a tierra y de falla por arco

Vérificateur de disjoncteur

de fuite à la terre et de fuite

d’arc électrique

Description

The Greenlee AFI-100 Arc Fault and Ground Fault Circuit Interrupter Tester is

intended to test the following:

• 15 A and 20 A, 120 VAC load center installed AFCI breakers with grounded

or ungrounded branch circuits

• 120 VAC AFCI outlets and AFCI branch outlets

• 15 A and 20 A, 120 VAC load center installed GFCI breakers

• 120 VAC GFCI outlets and GFCI branch outlets

• Polarity on any 120 VAC, 15 A or 20 A outlets

• AFCI/GFCI combination breakers and outlets

Safety

Safety is essential in the use and maintenance of Greenlee tools and

equipment. This instruction manual and any markings on the tool provide

information for avoiding hazards and unsafe practices related to the use of

this tool. Observe all of the safety information provided.

Purpose of This Manual

This instruction manual is intended to familiarize all personnel with the safe

operation and maintenance procedures for the Greenlee AFI-100.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge.

KEEP THIS MANUAL

All specifications are nominal and may change as design improvements occur.

Greenlee Textron shall not be liable for damages resulting from misapplication or

misuse of its products.

® Registered: The color green for electrical test instruments is a registered trademark

of Greenlee Textron.

AFI-100

Important Safety Information

This symbol is used to call your attention to hazards or unsafe practices

which could result in an injury or property damage. The signal word,

defined below, indicates the severity of the hazard. The message after the

signal word provides information for preventing or avoiding the hazard.

SAFETY ALERT SYMBOL

Immediate hazards which, if not avoided, WILL result in severe injury

or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury or

property damage.

Read and understand this material before

operating or servicing this equipment. Failure to

understand how to safely operate this tool can

result in an accident causing serious injury or

death.

Important Safety Information

Electric shock hazard:

• Do not apply more than the rated voltage between any two input

terminals, or between any input terminal and earth ground.

• Do not contact any uninsulated portion of the power cord.

Failure to observe these warnings can result in severe injury or death.

Electric shock and fire hazard:

• Do not expose this unit to rain or moisture.

• Do not use the unit if it is wet or damaged.

• Inspect the power cord before use. It must be clean and dry, and the

insulation must be in good condition.

• Use this unit for the manufacturer’s intended purpose only, as

described in this manual. Any other use can impair the protection

provided by the unit.

Failure to observe these warnings can result in severe injury or death.

Electric shock hazard:

Contact with live circuits can result in severe

injury or death.

AFI-100

Important Safety Information

• This tool is designed to test 15 A and 20 A, 120 VAC single-phase

AFCI and GFCI equipment only.

• The Polarity feature does not perform a comprehensive diagnostic

test; it performs a simple test to detect nearly all probable common

improper wiring conditions.

• Refer all indicated problems to a qualified electrician.

• This tool will not indicate the quality of ground, detect two hot wires in

a circuit, detect a combination of defects, or detect reversal of

grounded and grounding conductors.

• This tool simulates a certain type of arc and cannot represent all

arcing conditions. An AFCI that fails the AFI-100 test but passes the

button test may be operating properly.

Failure to observe these precautions can result in injury and can damage

the unit.

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity.

Refer to “Specifications.”

Failure to observe these precautions can result in injury and can damage

the unit.

Do not operate with the case open.

Failure to observe this warning can result in severe injury or death.

Identification

1. Polarity indicator

2. “FAILED” indicator

3. GFCI test button

4. AFCI test button

5. Power cord

1 2

Polarity Indicator

AFI-100

Operation

1. Test the unit on a known functioning circuit. If it does not function as

expected, return the unit to Greenlee for repair.

2. Perform the desired tests using the procedures below.

Polarity Test

•The Polarity feature does not perform a comprehensive diagnostic

test; it performs a simple test to detect nearly all probable common

improper wiring conditions.

•Refer all indicated problems to a qualified electrician.

•This tool will not indicate the quality of ground, detect two hot wires in

a circuit, detect a combination of defects, or detect reversal of

grounded and grounding conductors.

Failure to observe these precautions can result in injury and can damage

the unit.

1. Unplug all appliances or equipment on the circuit being tested to help

avoid erroneous readings.

2. Plug the AFI-100 into any standard 120 V three-wire receptacle.

Compare the LEDs illuminated on the AFI-100 to the “Polarity Indicator”

illustration on the previous page.

Note: If the LEDs indicate anything other than “CORRECT”, have the

wiring corrected by a qualified electrician.

3. Repeat step 2 for every receptacle on the circuit.

AFCI/GFCI Test

Operation (cont’d)

•This tool is designed to test 15 A and 20 A, 120 VAC single-phase

AFCI and GFCI equipment only.

•Refer all indicated problems to a qualified electrician.

•This tool simulates a certain type of arc and cannot represent all

arcing conditions. An AFCI that fails the AFI-100 test but passes the

button test may be operating properly.

Failure to observe these precautions can result in injury and can damage

the unit.

1. Consult the AFCI or GFCI device manufacturer’s installation instructions

to determine that the device is installed in accordance with the

manufacturer’s specifications.

2. Check for correct wiring of the receptacle and all remotely connected

receptacles on the branch circuit.

3. Unplug all appliances or equipment on the circuit being tested to help

avoid erroneous readings.

4. Operate the test button on the AFCI or GFCI device installed in the

circuit. The device must trip. If it does not, do not use the circuit.

Consult an electrician. If the device does trip, reset it.

5. Plug the AFI-100 into the receptacle to be tested. Observe the polarity

LEDs to verify that the outlet is correctly wired. Refer to the complete

instructions in the “Polarity Test”section of this manual.

6. Press and hold the AFCI or GFCI test button for at least 6 seconds. All

the LEDs on the AFI-100 must turn off, indicating that the AFCI or GFCI

device has tripped.

AFI-100

AFCI/GFCI Test (cont’d)

Operation (cont’d)

7. If the yellow “FAILED”LED lights, the test has run to completion without

tripping the device. This suggests:

•A wiring problem with a fully operable AFCI or GFCI device, or

•Proper wiring with a faulty AFCI or GFCI device. Consult an electrician

to check the condition of the wiring and device.

•No ground wire present in the outlet (GFCI test only).

8. Repeat steps 5 through 7 for every receptacle on the circuit.

Specifications

Arc Fault Test: (12) 112 A pulses

Pulse Width: 400 µs

Repetition Rate: 120 Hz

Ground Fault Test: 7 mA at 120 VAC

Polarity Indicator: 3 LEDs indicate proper wiring to the outlet being tested

Power: 120 VAC, 15 A or 20 A branch circuit

Operating Temperature: -25 °C to 80 °C (-13 °F to 176 °F)

Storage Temperature: -55 °C to 80 °C (-67 °F to 176 °F)

Maintenance

Cleaning

Periodically wipe the case with a damp cloth and mild detergent; do not use

abrasives or solvents.

•Do not attempt to repair this unit. It contains no user-serviceable

parts.

•Do not expose the unit to extremes in temperature or high humidity.

Refer to “Specifications.”

Failure to observe these precautions can result in injury and can damage

the unit.

Inhaltsverzeichnis

Sprachen:

Andere Greenlee Stromkreisprüfer Handbücher

Greenlee

Greenlee PG1 Bedienungsanleitung

Greenlee

Greenlee PairMapper Bedienungsanleitung

Greenlee

Greenlee GT-55e Bedienungsanleitung

Greenlee

Greenlee GT-10 Bedienungsanleitung

Greenlee

Greenlee GT-65e Bedienungsanleitung

Greenlee

Greenlee GT-10 Handbuch

Greenlee

Greenlee 1110 Bedienungsanleitung

Greenlee

Greenlee 5708 Bedienungsanleitung

Greenlee

Greenlee GT-10GFI Bedienungsanleitung

Greenlee

Greenlee GT-65 Bedienungsanleitung

Greenlee

Greenlee 5715 Bedienungsanleitung

Greenlee

Greenlee SVC-10 Bedienungsanleitung

Greenlee

Greenlee LT-100 Bedienungsanleitung

Beliebte Stromkreisprüfer Handbücher anderer Marken

IDEAL

IDEAL 61-534 Bedienungsanleitung

Kusam-meco

Kusam-meco KM 1812EL Bedienungsanleitung

MGE UPS Systems

MGE UPS Systems Galaxy 5000 Bedienungsanleitung

YOKOGAWA

YOKOGAWA MY10 Bedienungsanleitung

Power Probe Tek

Power Probe Tek PRO SERIES THE MAESTRO Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt DUSPOL expert 1000 Bedienungsanleitung

OEM

OEM 24366 Service-Handbuch

JDS Uniphase

JDS Uniphase IP Video Test Option HST-3000 Bedienungsanleitung

Sealey

Sealey FF400 Bedienungsanleitung

PEAKMETER

PEAKMETER PM8908C Bedienungsanleitung

YOKOGAWA

YOKOGAWA CL345 Bedienungsanleitung

ABB

ABB SACE Emax 2 Benutzerhandbuch

Elenco Electronics

Elenco Electronics LP-500 Bedienungsanleitung

Amprobe

Amprobe AMP-210 Bedienungsanleitung

Megger

Megger TPT420 Bedienungsanleitung

Extech Instruments

Extech Instruments CT70 Bedienungsanleitung

TERASAKI

TERASAKI TemPower 2 Bedienungsanleitung

Hioki

Hioki 3481-20 Bedienungsanleitung