Greenlee HID6506 Bedienungsanleitung
Hydraulic
Rotary Impact Drill
Serial Code AML
OPERATION MANUAL
Read and understand all of the instructions and
safety information in this manual before operating
or servicing this tool.
Register this product at www.greenlee.com
Español............... 15
Français.............. 29
Deutsch .............. 43
Italiano................ 57
99940116 REV 2 © 2012 Greenlee Textron Inc. 2/12
Hydraulic Rotary Impact Drill
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
2
Table of Contents
Description .................................................................... 2
Safety ............................................................................ 2
Purpose of this Manual ................................................. 2
Other Publications......................................................... 2
Important Safety Information .....................................3–5
Identication.................................................................. 6
Specications................................................................ 7
Setting the Super Spool ................................................ 8
Setting the Tool to Drill or Hammer Drill........................ 8
Installing and Removing Drill Bits.................................. 9
Hoses and Fittings ...................................................... 10
Typical Setup............................................................... 10
Hose Connections....................................................... 10
Operation..................................................................... 11
Maintenance................................................................ 12
Troubleshooting........................................................... 13
Español........................................................................ 15
Français....................................................................... 29
Deutsch ....................................................................... 43
Italiano......................................................................... 57
Description
The Greenlee Utility Hydraulic Rotary Impact Drill is
intended for use with impact-type bits for hammer
(impact) drilling in concrete, brick, rock and other
difcult-to-drill materials.
Features include a depth gauge, a directional spool for
forward or reverse operation, Super Spool™ for use
on either an Open-Center or Closed-Center hydraulic
system, and an insulated handle for operator comfort
and safety. A ow control cartridge, effective with
Serial Number 300, limits the hydraulic ow to 24.6 l/min
(6.5 gpm), allowing the tool to be connected to a
hydraulic system providing up to 45.4 l/min (12 gpm).
The tool also includes a variable torque output screw
and a built-in safety slip clutch to help prevent operator
injury if the drill bit catches.
Super Spool is protected by U.S. Patent No. 4548229.
KEEP THIS MANUAL
Safety
Safety is essential in the use and maintenance of
Greenlee Utility tools and equipment. This instruction
manual and any markings on the tool provide informa-
tion for avoiding hazards and unsafe practices related to
the use of this tool. Observe all of the safety information
provided.
Purpose of this Manual
This manual is intended to familiarize personnel with
the safe operation and maintenance procedures for the
following Greenlee Utility tool:
HID6506 (42309) Hydraulic Rotary Impact Drill
Serial Code AML
Keep this manual available to all personnel.
Replacement manuals are available upon request at no
charge at www.greenlee.com.
Other Publications
Tool Owners/Users
SAE Standard J1273 (Hose and Hose Assemblies):
Publication 99930323
Authorized Greenlee Utility Service Centers
Repair Manual: Publication 99915979
All specications are nominal and may change as design
improvements occur. Greenlee Textron Inc. shall not be liable for
damages resulting from misapplication or misuse of its products.
Super Spool is a trademark of Greenlee Textron Inc.
Hydraulic Rotary Impact Drill
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
3
IMPORTANT SAFETY INFORMATION
SAFETY
ALERT
SYMBOL
This symbol is used to call your attention to hazards
or unsafe practices which could result in an injury or
property damage. The signal word, dened below,
indicates the severity of the hazard. The message
after the signal word provides information for
preventing or avoiding the hazard.
Immediate hazards which, if not avoided, WILL result
in severe injury or death.
Hazards which, if not avoided, COULD result in
severe injury or death.
Hazards or unsafe practices which, if not avoided,
MAY result in injury or property damage.
Read and understand all of the
instructions and safety information
in this manual before operating or
servicing this tool.
Failure to observe this warning could
result in severe injury or death.
Wear eye protection when operating
or servicing this tool.
Failure to wear eye protection could
result in serious eye injury from ying
debris or hydraulic oil.
Wear hearing protection when using
this tool.
Failure to observe this warning could
result in serious injury.
Electric shock hazard:
This tool is not insulated. When
using this unit near energized electri-
cal lines:
• Use only certied non-conductive
hoses and proper personal protec-
tive equipment.
• Select and maintain the hydraulic
uid to meet the minimum dielec-
tric standards required by your
safety department.
Failure to observe this warning could
result in severe injury or death.
Skin injection hazard:
• Do not use ngers or hands to
check for leaks.
• Do not hold hose or couplers while
the hydraulic system is pressurized.
• Depressurize the hydraulic system
before servicing.
Oil under pressure easily punctures
skin causing serious injury, gangrene
or death. If you are injured by
escaping oil, seek medical attention
immediately.
Hydraulic Rotary Impact Drill
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
4
IMPORTANT SAFETY INFORMATION
• When using the tool in hammer drill mode, use
accessories that are approved for impact use
only. Accessories that are not approved for impact
applications can break when used in the hammer
drill mode.
• Inspect accessories before use. Discard accesso-
ries that have cracks, chips or gauges.
Failure to observe these warnings could result in
severe injury or death.
Some dust created by power sanding, sawing, grind-
ing, drilling, and other construction activities contains
chemicals known to the State of California to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement and other
masonry products
• Arsenic and chromium from chemically-treated
lumber.
To reduce your exposure to these chemicals: work in
a well ventilated area, and work with approved safety
equipment, such as dust masks that are specially
designed to lter out microscopic particles.
• Remove the chuck key from the chuck before drill-
ing. Operation with the key in the chuck can result
in severe injury.
• Keep all parts of the body away from rotating parts
when the tool is in operation. Contact with moving
parts can result in severe injury.
• Do not change accessories, inspect or clean tool
when it is connected to a power source. Accidental
start-up can result in serious injury.
• Maintain a rm grip on tool, using both hands at all
times. Serious injury can result if an operator does
not control the tool.
• Do not lock trigger in the power-ON position.
Operator cannot stop tool when trigger is locked.
Failure to observe these warnings could result in
severe injury or death.
Tool and accessory may be hot
during and after operation.
Contact with hot surfaces could
result in serious injury.
Do not exceed the following hydraulic power source
maximums:
• Hydraulic ow: 45.4 l/min (12 gpm)
• Pressure relief setting: 138 bar (2000 psi)
• Back pressure: 13.8 bar (200 psi)
Failure to observe this warning could result in severe
injury or death.
Do not disconnect tool, hoses, or ttings while
the tool is running or if the hydraulic uid is
hot. Hot hydraulic uid can cause serious burns.
Do not reverse hydraulic ow. Operation with
hydrau-
lic ow reversed can cause tool malfunction.
Connect
the supply (pressure) hose and return (tank) hose to
the proper tool ports.
Failure to observe this warning could result in severe
injury or death.
Hydraulic Rotary Impact Drill
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
5
IMPORTANT SAFETY INFORMATION
• Wear protective gloves when handling, removing,
and installing drill bits. Drill bits can cut even when
stationary.
• Inspect tool before use. Replace any worn
or damaged parts. A damaged or improperly
assembled tool can malfunction, injuring nearby
personnel.
• Inspect the hydraulic hoses and couplings every
operating day. Repair or replace if leakage, crack-
ing, wear, or damage is evident. Damaged hoses
or couplings can fail, resulting in injury or property
damage.
• Use this tool for manufacturer’s intended use only.
Use other than that which is described in this
manual could result in injury or property damage.
• Make sure all bystanders are clear of the work area
when handling, starting, and operating the tool.
Nearby personnel can be injured by ying parts in
the event of a tool malfunction.
Prolonged exposure to vibration or very repetitive
hand and arm movements may cause injury. Stop
using any tool if discomfort, tingling feeling, or pain
occurs. Consult a physician before resuming use of
the tool.
Procedure for disconnecting hydraulic hoses, ttings
or components:
1. Move the ow lever on the hydraulic power
source to the OFF position.
2. Stop the power source.
3. Follow the sequence under Disconnecting Hoses
to prevent pressure buildup. In case some
pressure has built up, loosen hoses, ttings, or
components slowly.
Emergency stop procedure:
1. Release the trigger.
2. Shut off the hydraulic power source.
Note: Keep decals clean and legible. Replace decals
when necessary—see the decals listed in the Service
manual.
Hydraulic Rotary Impact Drill
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
6
Identification
8
9
11
12
13
14
1
2
3
4
5
6
7
10
1. Trigger
2. Drill/Hammer Drill Selector Knob
3. Collar
4. Depth Gauge
5. Auxiliary Handle
6. Lifting Hook
7. Motor Cap
Hydraulic Rotary Impact Drill
8. Serial Number
9. Super Spool
10. Directional Spool
11. Handle
12. Tank Port
13. Pressure Port
14. Variable Torque Output Screw
Hydraulic Rotary Impact Drill
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
7
Hydraulic Rotary Impact Drill
Type of Hydraulic System ....................... Open-Center or
Closed-Center
Hydraulic Pressure Port.............3/4–16 SAE O-ring Boss
Hydraulic Tank Port ...................3/4–16 SAE O-ring Boss
Bits
SDS Plus Type Chuck ................ SDS Plus Type Shank
Noise Levels
Sound Power Level (maximum) ..........................85 LWA
Mass/Weight................................................ 4.1 kg (9 lbs)
Length ..................................................... 285 mm (11.2")
Width ........................................................... 89 mm (3.5")
Height...................................................... 280 mm (11.0")
Output
Revolutions per Minute @ 18.9 l/min (5 gpm) .........900
Revolutions per Minute @ 22.7 l/min (6 gpm) .......1050
Impacts per Minute @ 22.7 l/min (6 gpm) .............5400
Max. Single Impact Energy ...................................2.4 J
Drilling Capacity
Concrete................................................... 22 mm (7/8")
Steel ......................................................... 13 mm (1/2")
Wood.....................................................30 mm (1-1/8")
Core Bit .................................................68 mm (2-5/8")
Hydraulic Power Source
Do not exceed the following hydraulic power source
maximums:
• Hydraulic ow: 45.4 l/min (12 gpm)
• Pressure relief setting: 138 bar (2000 psi)
• Back pressure: 13.8 bar (200 psi)
Failure to observe this warning could result in severe
injury or death.
Type of Hydraulic System........................ Open-Center or
Closed-Center
Flow
Minimum ..........................................15.1 l/min (4 gpm)
Recommended.................................22.7 l/min (6 gpm)
Maximum .......................................45.4 l/min (12 gpm)
Pressure Relief Setting
Minimum ......................................... 68.9 bar (1000 psi)
Maximum ......................................... 138 bar (2000 psi)
Filtration............................................ 10 micron (nominal)
Back Pressure (maximum)* .................. 13.8 bar (200 psi)
* 13.8 bar (200 psi) is the maximum agreed standard back pressure
for the HTMA (Hydraulic Tool Manufacturers Association).
Greenlee Utility tool will operate satisfactorily at this standard.
1. Maximum hydraulic uid temperature must not
exceed 60 °C (140 °F). A sufcient oil cooling
capacity is needed to limit the hydraulic uid
temperature.
2. Hydraulic ow must not exceed 45.4 l/min (12 gpm).
Install a ow meter in the return line to measure the
rate of hydraulic ow before using the tool.
3. Pressure relief valve setting must not exceed
138bar (2000 psi) at your tool’s maximum ow.
Locate the pressure relief valve in the supply circuit
to limit excessive hydraulic pressure to the tool.
Hydraulic Schematic
FILTER
(10 MICRON)
COOLER
RELIEF
VALVE
138 bar
(2000 psi)
CONTROL
VALVE FLOW METER
T
PTOOL
RESERVOIR
PUMP
POWER SOURCE
Recommended Hydraulic Fluids
Use any non-detergent, petroleum-based hydraulic
uid which meets the following specications or HTMA
specications.
S.U.S. @:
38 °C (100 °F)...............................................140 to 225
99 °C (210 °F)............................................ 40 minimum
Flash Point................................170 °C (340 °F) minimum
Pour Point..................................-34 °C (-30 °F) minimum
Specifications
Hydraulic Rotary Impact Drill
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
8
Setting the Super Spool
The Super Spool allows the tool to be used with either
Open-Center or Closed-Center hydraulic systems.
Open-Center Hydraulic System
Use a wrench to turn the Super Spool until the letter “O”
on the spool is aligned with the letter “C” on the tool
handle.
Closed-Center Hydraulic System
Use a wrench to turn the Super Spool until the letter “C”
on the spool is aligned with the letter “C” on the tool
handle.
Setting the Tool to Drill
or Hammer Drill
The drill/hammer drill selector knob allows the tool to
be used for either standard drilling or hammer (impact)
drilling. Depress the red indication arrow (1) to turn the
selector knob.
23
1
Set the knob so that the red arrow icon (1) points to the
desired operation:
• Drill bit icon (2) for standard drilling
• Hammer icon (3) for hammer drilling
Setting the Super Spool
Closed-Center Open-Center
Hydraulic Rotary Impact Drill
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
9
Installing and Removing Drill Bits
Greenlee Utility recommends using Greenlee impact-
style bits. See Accessories in this manual.
• When using the tool in hammer drill mode, use
accessories that are approved for impact use
only. Accessories that are not approved for impact
applications can break when used in the hammer
drill mode.
• Inspect accessories before use. Discard accesso-
ries that have cracks, chips or gauges.
Failure to observe these warnings could result in
severe injury or death.
Some bits may whip or bend under sideload.
• Do not use bits with a long spiral and center
support.
• When using an impact bit, run the power source
at the minimum ow. Refer to the “Specications”
section.
Failure to observe this warning could result in severe
injury or death.
Long SpiralCenter Support
x
SDS Plus Type Chuck
1. Inspect the chuck. Remove any dirt or other
contamination.
2. Select an SDS Plus type of bit. Align the long slots
in the shank of the bit with the index mark in the
dust cover on the end of the collar. Insert the bit into
the chuck.
3. Check to make sure the collar is securely holding
the bit.
4. To remove the drill bit, twist the collar so that it
releases the bit.
Hydraulic Rotary Impact Drill
Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070
10
Hose Connections
Tool Port Identification
One of three methods is used to identify the pressure
and tank ports of Greenlee Utility tools. Match the mark-
ings on your tool to this table.
Pressure Port Tank Port
P T
or
In Out
Connecting Hoses
1. Move the ow lever on the hydraulic power source
to the OFF position.
2. Stop the hydraulic power source.
3. Connect the tank hose to the tank port on the
power source, and then to the tank port on the tool.
4.
Connect the pressure hose to the pressure port on
the tool, and then to the pressure port on the power
source.
Disconnecting Hoses
1. Move the ow lever on the hydraulic power source
to the OFF position.
2. Stop the hydraulic power source.
3. Disconnect the pressure hose from the power
source, and then from the tool.
4. Disconnect the tank hose from the tool, and then
from the power source.
5. Install dust caps over the ports to prevent
contamination.
Hoses and Fittings
Installation and Maintenance
See publication 99930323, SAE Standard J1273
(Hoseand Hose Assemblies).
Replacement
See a Greenlee Utility catalog or Greenlee Utility
publication 99910322, Low Pressure Quick Couplers,
Adapters and Hoses.
Do not disconnect tool, hoses, or ttings while
the power source is running or if the hydraulic uid is
hot. Hot hydraulic uid could cause serious burns.
Typical Setup
Andere Handbücher für HID6506
1
Inhaltsverzeichnis
Sprachen:
Andere Greenlee Bohren Handbücher
Greenlee
Greenlee LRH-144 Bedienungsanleitung
Greenlee
Greenlee HID6506 Bedienungsanleitung
Greenlee
Greenlee Fairmont H6400C Bedienungsanleitung
Greenlee
Greenlee Fairmont H6400C Bedienungsanleitung
Greenlee
Greenlee 38456 Bedienungsanleitung
Greenlee
Greenlee Fairmont H6400C Bedienungsanleitung
Greenlee
Greenlee Fairmont H6400 Bedienungsanleitung
