Greenlee HB10 Dynapress Bedienungsanleitung

OPERATION MANUAL

HB10 Dynapress®

Hydraulic Booster

Read and understand all of the instructions and

safety information in this manual before operating

or servicing this tool.

Español............... 13

Français.............. 25

Deutsch .............. 37

Italiano................ 49

HB10 Dynapress®Hydraulic Booster

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Safety

Safety is essential in the use and maintenance of

Greenlee Utility tools and equipment. This instruction

manual and any markings on the tool provide informa-

tion for avoiding hazards and unsafe practices related to

the use of this tool. Observe all of the safety information

provided.

Purpose of this Manual

This instruction manual is intended to familiarize

all personnel with the safe operation and maintenance

procedures for the Greenlee Utility HB10 Dynapress®

Hydraulic Booster.

Keep this manual available to all personnel.

Replacement manuals are available upon request

at no charge at www.greenlee.com.

Other Publications

Tool Owners/Users

Specications and Parts Manual:

Publication 99933390

SAE Standard J1273 (Hose and Hose Assemblies):

Publication 99930323

All specications are nominal and may change as design

improvements occur. Greenlee Textron Inc. shall not be liable for

damages resulting from misapplication or misuse of its products.

Dynapress®is a registered trademark of Greenlee Textron Inc.

KEEP THIS MANUAL

Table of Contents

Description .................................................................... 2

Purpose ......................................................................... 2

Important Safety Information ..................................... 3-5

Identication.................................................................. 6

Hoses and Fittings ........................................................ 7

Hose Connections......................................................... 7

Typical Setup................................................................. 7

Operation....................................................................... 8

Maintenance.................................................................. 9

Troubleshooting........................................................... 10

Accessories................................................................. 11

Description

The Greenlee Utility HB10 Dynapress®Hydraulic

Booster is a piston-type accessory intended to allow the

use of a high pressure/low ow tool with a low pressure/

high ow hydraulic power source. Compatible with

either Open-Center or Closed-Center hydraulic systems,

the unit takes a hydraulic input of 69 to 152 bar (1000to

2200 psi) and produces a stable output of 700 bar

(10,000 psi).

The HB10 can be installed in existing two-hose type

hydraulic systems, and does not require a third hydrau-

lic line or separate reservoir. The compact and light-

weight design allows the unit to be easily carried and

used on the ground or in an aerial lift basket. Actuating

the high-pressure circuit of the Dynapress requires a

remote control valve, purchased separately. The instruc-

tions and illustrations in this manual reect using the

HB10 with either of the following Greenlee Utility remote

control valves:

PVA0021A (Single-Acting Control Valve)

PVA0022A (Double-Acting Control Valve)

The terms “unit” and “booster,” when used in this

manual, refer to the HB10. The term “tool” refers to the

device (cable cutter, crimping tool, etc) that is powered

by the HB10.

HB10 Dynapress®Hydraulic Booster

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

IMPORTANT SAFETY INFORMATION

SAFETY

ALERT

SYMBOL

This symbol is used to call your attention to hazards

or unsafe practices which could result in an injury or

property damage. The signal word, dened below,

indicates the severity of the hazard. The message

after the signal word provides information for pre-

venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result

in severe injury or death.

Hazards which, if not avoided, COULD result in

severe injury or death.

Hazards or unsafe practices which, if not avoided,

MAY result in injury or property damage.

Read and understand all of the

instructions and safety information

in this manual before operating or

servicing this tool.

Failure to observe this warning will

result in severe injury or death.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection can

result in serious eye injury from

ying debris or hydraulic oil.

HB10 Dynapress®Hydraulic Booster

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Electric shock hazard:

This booster is not insulated. When

using this unit near energized elec-

trical lines:

• Use only certied non-conductive

hoses and proper personal protec-

tive equipment.

• Select and maintain the hydraulic

uid to meet the minimum dielec-

tric standards required by your

safety department.

Failure to observe this warning can

result in severe injury or death.

Skin injection hazard:

Oil under pressure easily punctures

skin causing serious injury, gan-

grene or death. If you are injured by

escaping oil, seek medical attention

immediately.

• Do not use ngers or hands to

check for leaks.

• Do not hold hose or couplers

while

the hydraulic system is

pressurized.

• Depressurize the hydraulic system

before servicing.

Booster may be hot during and after

operation. Allow unit to cool before

handling, or handle with heat-resis-

tant gloves.

Hot surfaces can cause severe

burns.

Do not exceed the maximum hydraulic ow, pressure

relief or back pressure listed in the Specications

and Parts manual.

Failure to observe this warning can result in severe

injury or death.

Do not disconnect booster, hoses, or ttings while

the power source is running or if the hydraulic uid

is hot. Hot hydraulic uid can cause serious burns.

Do not reverse hydraulic ow. Operation with

hydraulic ow reversed can cause a malfunction.

Connect the supply (pressure) hose and return (tank)

hose to the proper ports.

Failure to observe this warning can result in severe

injury or death.

• Inspect the hydraulic hoses and couplings every

operating day. Repair or replace if leakage, crack-

ing, wear, or damage is evident. Damaged hoses

or couplings can fail, resulting in injury or property

damage.

• Make sure all bystanders are clear of the work

area when handling, starting and operating tool.

Nearby personnel can be injured by ying or

falling debris or by ying parts in the event of a

malfunction.

Failure to observe these warnings can result in

severe injury or death.

IMPORTANT SAFETY INFORMATION

HB10 Dynapress®Hydraulic Booster

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

IMPORTANT SAFETY INFORMATION

Inspect unit before operating. Replace any worn,

damaged or missing components with Greenlee

Utility replacement parts. A damaged or improperly

assembled component can fail and strike nearby

personnel.

Failure to observe this precaution can result in

severe injury or death.

Use this tool for manufacturer’s intended purpose

only. Use other than that which is described in this

manual can result in injury or property damage.

Failure to observe this precaution can result in injury

or property damage.

Hydraulic oil can cause skin irritation.

• Handle the booster and hoses with care to prevent

skin contact with hydraulic oil.

• In case of accidental skin contact with hydraulic

oil, wash the affected area immediately to remove

the oil.

Failure to observe these precautions can result in

injury.

Emergency stop procedure:

1. Move the remote control valve’s lever to the

neutral position.

2. Move the ow lever on the hydraulic power

source to the OFF position.

Procedure for disconnecting hydraulic hoses, ttings

or components:

1. Move the ow lever on the hydraulic power

source to the OFF position.

2. Stop the power source.

3. Follow the sequence under Disconnecting

Hoses to prevent pressure buildup. In case

some pressure has built up, loosen hoses, t-

tings or components slowly.

Note: Keep decals clean and legible. Replace

decals when necessary—see the decals listed in the

Speciﬁcations and Parts manual.

HB10 Dynapress®Hydraulic Booster

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Identiﬁcation

1. Handle

2. Input Side Pressure Port

3. Input Side Tank Port

4. Unloading Valve

5. Output Side Tank Port

6. Output Side Pressure Port

Input Side

69 to 152 bar (1000 to 2200 psi)

Output Side

700 bar (10,000 psi)

HB10 Dynapress®Hydraulic Booster

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Hoses and Fittings

Installation and Maintenance

See publication 99930323,

SAE J1273 (Hose and Hose Assemblies).

Replacement

See a Greenlee Utility catalog or Greenlee Utility

publication 99910322, Low Pressure Quick Couplers,

Adapters and Hoses.

Hose Connections

Connecting Hoses

Use this procedure to prevent pressure buildup in the

hydraulic circuit:

1. Move the ow lever on the hydraulic power source

to the OFF position.

2. Stop the hydraulic power source.

3. Connect high-pressure hoses to the high-pressure

ports as follows:

return (tank) hose: remote control valve to booster

supply (pressure) hose: remote control valve to

booster

*return (tank): remote control valve to tool

supply (pressure) hose: remote control valve to

tool

* This step applies to double-acting tool and control

valve only.

4. Connect the low-pressure hoses to the low-pressure

ports as follows:

return (tank) hose: booster to power source

supply (pressure) hose: power source to booster

Disconnecting Hoses

Use this procedure to prevent pressure buildup in the

hydraulic circuit:

1. Move the ow lever on the hydraulic power source

to the OFF position.

2. Stop the hydraulic power source.

3. Disconnect the hoses in reverse order of the con-

nection sequence.

4. Install dust caps to prevent contamination.

Typical Setup

Power Source

HB10 PVA0021A Single-Acting

Tool

Optional:

Tool connected to control valve

HB10 Dynapress®Hydraulic Booster

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Operation

Electric shock hazard:

This booster is not insulated. When

using this unit near energized elec-

trical lines:

• Use only certied non-conductive

hoses and proper personal protec-

tive equipment.

• Select and maintain the hydraulic

uid to meet the minimum dielec-

tric standards required by your

safety department.

Failure to observe this warning can

result in severe injury or death.

Skin injection hazard:

Oil under pressure easily punctures

skin causing serious injury, gan-

grene or death. If you are injured by

escaping oil, seek medical attention

immediately.

• Do not use ngers or hands to

check for leaks.

• Do not hold hose or couplers

while

the hydraulic system is

pressurized.

• Depressurize the hydraulic system

before servicing.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection can

result in serious eye injury from

ying debris or hydraulic oil.

Read and understand all of the instructions and

safety information supplied with the tool.

Failure to observe this warning can result in severe

injury or death.

1. Start the hydraulic power source.

Note: Allow the power source to run for a few

minutes to warm the hydraulic ﬂuid.

2. To actuate the tool, press down and hold the lever in

the ADVANCE position.

• When the pressure exceeds approximately

207bar (3000 psi), the operator may release the

control lever. The lever will remain in the

ADVANCE position.

• When the pressure reaches the relief setting of

the unloading valve – 700 bar (10,000 psi) – the

high pressure oil will dump back to tank and the

system pressure will drop to nearly zero. The

operator can then release the remote control lever

back to the neutral position.

3. To return or retract the ram, press down and hold

the lever in the RETRACT position.

HB10 Dynapress®Hydraulic Booster

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Maintenance

Skin injection hazard:

Oil under pressure easily punctures

skin causing serious injury, gan-

grene or death. If you are injured by

escaping oil, seek medical attention

immediately.

• Do not use ngers or hands to

check for leaks.

• Do not hold hose or couplers

while

the hydraulic system is

pressurized.

• Depressurize the hydraulic system

before servicing.

Wear eye protection when operating

or servicing this tool.

Failure to wear eye protection can

result in serious eye injury from

ying debris or hydraulic oil.

Notes:

(1) Keep all decals clean and legible. Replace decals

when necessary. See the Speciﬁ–cations and Parts

manual for decal part numbers.

(2) When disposing of any components (hydraulic

hoses, hydraulic ﬂuid, worn parts, etc.), do so in

accordance with federal, state and local laws or

ordinances.

Daily

1. Wipe all booster surfaces clean.

2. Inspect the hydraulic hoses and ttings for signs

of leaks, cracks, wear or damage. Replace if

necessary.

3. Install dust caps when the unit is disconnected.

Monthly

Perform a thorough inspection of the hydraulic hoses

and ttings as described in publication 99930323,

SAE J1273 (Hose and Hose Assemblies).

Periodically

Use a non-lled pressure gauge, like the Greenlee Utility

137779, to verify that the unloading valve relief pres-

sure is 700 bar (10,000 psi). Send the booster to an

authorized Greenlee Utility service center if adjustment

is necessary.

Annually

If required by your organization, have the tool inspected

by a Greenlee Utility Authorized Service Center.

HB10 Dynapress®Hydraulic Booster

Greenlee / A Textron Company 4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

Problem Probable Cause Probable Remedy

Booster does not operate. Improper power source. Verify that the power source meets the

specications. See the Specications

and Parts manual.

Hydraulic uid level low. Check the uid level. Check system for

leaks.

Incorrect hydraulic uid viscosity. Use hydraulic uid with the correct

viscosity. See the Specications and

Parts manual.

Booster operates slowly or

erratically. Hydraulic uid cold. Allow uid to warm to the operating

temperature. Actuate the tool intermit-

tently to reduce the warming time.

Power source not adjusted correctly. Refer to the power source operator’s

manual. Set the ow and pressure to

correspond with the booster.

Hydraulic uid level low. Check the uid level. Check system for

leaks.

Air in the hydraulic system. See power source manufacturer’s

instructions for removing air from the

system.

Incorrect hydraulic uid viscosity. Use hydraulic uid with the correct

viscosity. See the Specications and

Parts manual.

Booster feels hot. Hydraulic uid level low. Check the uid level. Check for leaks.

Incorrect hydraulic uid viscosity. Use hydraulic uid with the correct

viscosity. See the Specications and

Parts manual.

Hydraulic uid dirty. See the power source owner’s manual

for procedure to replace hydraulic oil

and lter.

Troubleshooting

Before troubleshooting, determine whether the problem

is in the booster, the hoses, or the power source.

Substitute a booster, hoses, or power source known to

be in good working order to eliminate the item that is

not operating.

If the problem is in the booster, see the troubleshoot-

ing table in this manual. If the problem is in the power

source, see the troubleshooting section of the power

source instruction manual.

Inhaltsverzeichnis

Sprachen:

Andere Greenlee Extender Handbücher

Greenlee

Greenlee 3561 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung