GreenTech Capwall Bedienungsanleitung

User Manual Capwall

E-Mail: info@greenteche.com

https://www.greenteche.com

BETTER ENERGY BETTER LIFE

— 1 —

GREEN TECH

Max. and min. cell

temperature & serial number

Stop & E-stop

switch

Capwall

Wall Mountable Energy Storage System

Scope This user manual is applied to Graphene Supercapacitor Battery

Capwall manufactured by Shanghai Green Tech Co.,Ltd.

Product Description

Product name: Capwall

Model: GTEM-400V14400-W

Mounting Option

Flat Floor

Solid wall

1. Product Drawing

System voltage

System current

System SOC

System status

Green Tech trade mark

Rubber foot*4

Charge/discharge terminals

Internal debugging CAN interface

Label of system specifications

Label of caution and emergency situations

Start Switch

Wall mounted hang buckle

Label of serial number

Max. and min. cell voltage

& serial number

Relays status

‘1’is on，

‘0’is off

External communication CAN interface

High voltage warning label

User Manual Capwall

E-Mail: info@greenteche.com

https://www.greenteche.com

BETTER ENERGY BETTER LIFE

— 2 —

GREEN TECH

Negative socket

Stop button

2. Inspection when arrived hand

A. Check the box to make sure not be damaged and then open the box.

B. Take out the module put at flat floor and check all the accessories.

C. Rotate clockwise ( pulled out ) the stop button,press and hold the switch until the screen lights up and release the switch.check

the display show “OK”.

Remark: take photo or video immediately and contact the local reseller or Green Tech if meet any unusual condition.

3. Battery power on & off operation

(1) Battery power on operation

First, make sure that the ‘STOP’ button is not locked and can be rotated，

Press and hold the start switch(5S) until the screen lights up and release the switch. The BMS starts the self-test until the correct

voltage, current, SOC and temperature information are displayed on the screen. The BMS self-test is completed and the battery can

be used normally. If the battery doesn't work properly, please contact the after-sales service engineer.

(2) Battery power off operation

Press the ‘STOP’ button

In case of emergency, please quickly press the stop button to cut off the battery and restart the battery after troubleshooting,

4. Battery External Connection Description

Positive HZ8.0 Negative HZ8.0 Cable 4AWG

The positive socket is orange, corresponding to the orange positive plug, and the negative socket is black, corresponding to the

negative black plug. When connecting the power cable, do not short circuit the positive and negative, so as not to damage the

battery and cause danger.

Please align the positioning slot on the plug and socket and insert it. When pulling out the plug, press the key on the side of the

plug, rotate the plug, and pull out after the slot is aligned.

Positive socket

Key

Ethernet communicate port

Start Switch

User Manual Capwall

E-Mail: info@greenteche.com

https://www.greenteche.com

BETTER ENERGY BETTER LIFE

— 3 —

GREEN TECH

5. Communication Function

a) Communication Interface Definition

b）Communication Mode

The internal debugging CAN interface is used to connect the upper computer of BMS to view the detailed parameter information,

status, fault detection and troubleshooting of the system.

External communication CAN interface is used to connect inverter and other communicable devices (communication protocol should

be matched) for system information transmission and detection.

6. Installation

a) Install on floor

b) Wall mounting

The Capwall must be mounted on the solid wall.

X2/X10(RJ45)

Internal debugging

CAN interface

External communication

CAN interface

Pin 1

Pin 2

Pin 3

Pin 4

I-CAN-H

V-CAN-H

Pin 5

I-CAN-L

V-CAN-L

Pin 6

I-CAN- GND

V-CAN- GND

Pin 7

Pin 8

X2/X10(RJ45) port

1,Screw the 4pcs rubber feet at the

bottom of the Capwall tightly.

2,Put it by vertically at clean,

drafty and flat floor.

1,Mark position of 5 holes. Drill holes with φ8 drill,and

depth at least 80mm.Install the expansion tubes, then

install the bracket and tighten the expansion bolts.

2,Put the Capwall on the wall and lock

the hang buckle with bracket.

User Manual Capwall

E-Mail: info@greenteche.com

https://www.greenteche.com

BETTER ENERGY BETTER LIFE

— 4 —

GREEN TECH

58V

324V

60A

-60A

453V

453.6

7. Charging-discharging

Charge-discharge profile

Note：If the charger needs to set the floating charge voltage, it is recommended to set the UFloat value to 453V.

8. Specifications

Part Number

GTEM-400V14400-W

Energy storage

14.4KWh

Nominal Voltage

400V/DC

Maximum Charge Voltage

453.6V/DC

Discharge Cut-off Voltage

324V/DC

ESR/AC @1KHz 50% SOC

<100mΩ

Max. Continuous Charge Current

60A

Max. Continuous Discharge Current

60A

Round Trip Efficiency

98%

Cooling Method

Natural

Cells Self-discharge Rate

2% per month

Recommended Depth of Discharge

≤90%

Maximum Depth of Discharge

100%

Ingress Protection Rating

IP42

Shell Material

Metal & ABS plastic

Monitoring Data

System voltage,current, temperature,SOC,SOH,cycle,cell’s voltage

Charging Temperature Range

0°C to +55°C

Discharging Temperature Range

-20°C to +60°C

User Manual Capwall

E-Mail: info@greenteche.com

https://www.greenteche.com

BETTER ENERGY BETTER LIFE

— 5 —

GREEN TECH

9. Battery Management System (BMS)

(1) BMS Electrical Diagram

The system is function modularity design.

a) The interface of charge and discharge is integrated.

b) The cell voltage and battery temperature is detected by BMS.

(2) Smart BMS Parameter

10. Troubleshooting

NO.

Item

Parameter

Remark

Cells Balancing

Active

Smart active balancing

Over-temperature

55℃

Shutdown

Short Circuit Protection

300A

Fused and need to change fuse block

Charging Cut-off Voltage

453.6V

Shutdown

Discharge Protection Voltage

324V

Shutdown

GPS/GPRS

Option

System status

User Manual Capwall

E-Mail: info@greenteche.com

https://www.greenteche.com

BETTER ENERGY BETTER LIFE

— 6 —

GREEN TECH

Alarm Status

Description

Solution

The system is in normal state

TVol.OH 1&2&3

The total system voltage

exceeds the alarm value

1. TVol.OH 1&2, Alarm information, the system can be used

normally, The battery is about to be fully charged.

2. TVol.OH 3, When the system voltage reaches the charging

cut-off voltage , ‘KG 1 = 0’ (charging relay is off), charging is

prohibited and the system can discharge normally. When the

voltage reaches the recovery threshold, the charging relay is

on(‘KG 1=1’) and the system returns to normal state.

TVol.OL 1&2&3

The total system voltag is

lower than the alarm value

1. TVol.OL 1&2, Alarm information, the system can be used

normally, The battery is running out

2. TVol.OH 3, The system voltage reaches the discharging cut-off

voltage , The system will shut down automatically. Please restart

the battery and charge it immediately.

DVol.OH 1&2&3

A cell voltage exceeds the

alarm value

1. DVol.OH 1&2, Alarm information, the system can be used

normally, The battery is about to be fully charged.

2. DVol.OH 3, A cell voltage reaches the charging cut-off

voltage , ‘KG 1 = 0’ (charging relay is off), charging is prohibited

and the system can discharge normally. When the voltage reaches

the recovery threshold, the charging relay is on(‘KG 1=1’) and the

system returns to normal state.

DVol.OL 1&2&3

A cell voltage is lower than

the alarm value

1. DVol.OL 1&2, Alarm information, the system can be used

normally, The battery is running out

2. DVol.OL 3, A cell voltage reaches the discharging cut-off

voltage , The system will shut down automatically. Please restart

the battery and charge it immediately.

VC Fault 1&2&3

The voltage difference

between single cells exceeds

the alarm value

1. VC Fault 1&2, Alarm information, the system can be used

normally, Please charge once with less than 3A current until the

battery is fully charged.

2. VC Fault 3, The system will shut down automatically. Please

contact the after-sales personnel to maintain the battery system.

It is forbidden to disassemble the battery without permission to

avoid harm

Temp. OL 1&2&3

The temperature of the cell

lower than the alarm value.

1. Temp. OL 1&2, Alarm information, the system can be used

normally, It is recommended to reduce the charging power or

discharge power, or turn off the battery system for several hours,

and then continue to use it when the temperature drops,

2. Temp. OL 3, When the temperature is lower than 0 ℃,

charging is forbidden and the discharge power is reduced as much

as possible; When the temperature is lower than - 20 ℃, charging

& discharging is forbidden.The battery system will automatically

shut down and stand for a few hours until the temperature

rise ,then restart the battery to continue to use. If the problem is

not solved after restart, please contact your local dealer.

Temp. OH 1&2&3

The temperature of the cell

exceeds the alarm value.

1. Temp. OH 1&2, Alarm information, the system can be used

normally, It is recommended to reduce the charging power or

User Manual Capwall

E-Mail: info@greenteche.com

https://www.greenteche.com

BETTER ENERGY BETTER LIFE

— 7 —

GREEN TECH

discharge power, or turn off the battery system for several hours,

and then continue to use it when the temperature rise,

2. Temp. OH 3, The battery system will automatically shut

down and stand for a few hours, then restart the battery to

continue to use. If the problem is not solved after restart, please

contact your local dealer.

TC Fault 1&2&3

The temperature difference

between single cells exceeds

the alarm value.

1. TC Fault 1&2, Alarm information, the system can be used

normally, It is recommended to turn off the battery system for a

few hours and then restart the battery

2.TC Fault 3, The system will shut down automatically. It is

recommended to turn off the battery system for a few hours, and

then restart the battery. If the fault is not eliminated, please

contact your local dealer.

Charge OC 1&2&3

Charging current exceeds

alarm value

1 Charge OC 1&2, Alarm information, the system can be used

normally, This fault is eliminated when the charging current is

reduced.

2 Charge OC 3, The battery will automatically turn off the charging

relay and prohibit charging. When the charging power is reduced,

restart the system manually to recover.

Discharge OC 1&2&3

Discharging current exceeds

alarm value

1 Discharging OC 1&2, Alarm information, the system can be used

normally, This fault is eliminated when the Discharging current is

reduced.

2 Discharging OC 3, The battery will shut down automatically .

When the discharging power is reduced, restart the system

manually to recover.

SOC OL 1&2&3

SOC is too low, power is about

to run out.

SOC OL 1&2&3, Alarm information, the system can be used

normally, Please charge the battery system in time.

Insul Insp Fault

1&2&3

The insulation resistance is

too low

Insul Insp Fault 1&2&3, If the alarm message appears during the

BMS start-up self-test stage or during the use of the battery,

please turn off the battery and contact the local dealer to

checkthe insulation resistance value of the battery and remove

the fault.

Insul CC Fault 1&2&3

The insulation monitor is not

in normal working condition.

Insul CC Fault 1&2&3, If the alarm message appears during the

BMS start-up self-test stage or during the use of the battery,

please turn off the battery and contact the local dealer to check

the insulation monitor of the battery and remove the fault.

DCM Fault 1&2&3

Incorrect connection of

communication line

DCM Fault 1&2&3, Please contact the local dealer to check

whether the communication cable is connected correctly, or

whether the communication connector is loose or off.

Temp. Line Fault

1&2&3

The temperature sensor is not

working properly.

Temp. Line Fault 1&2&3, Please contact the local dealer to check

whether the temperature sensor is loose or falling off.

Vol. Line Fault

1&2&3

The temperature acquisition

line is not working properly

Please contact the local dealer to check whether the temperature

acquisition line is loose or falling off.

User Manual Capwall

E-Mail: info@greenteche.com

https://www.greenteche.com

BETTER ENERGY BETTER LIFE

— 8 —

GREEN TECH

11. Inverter Connection and Setting

1) Compatible inverters

a) Connect the communication cable with inverter

b) Choose “Lithium Battery ” Mode

c) Choose “Green Tech Battery System”

d) Following the inverter installation guide set step by step

2) Incompatible inverters

a) Do not connect the communication cable

b) Might need to connect temperature detector with inverter (usually offer from inverter manufacturer)

c) Choose “Lead Acid Battery” mode

d) Set the charging voltage,float charging voltage and charging current.

e) Following inverter’s user manual installation guide of Lead acid battery mode.

12. Caution

Place the module out of the reach of children and infants.

Do not place the module in microwave ovens or other similar appliances.

Do not remove the product label.

Do not attempt to open or service the battery pack.

Do not expose to temperatures above 80℃.

Do not short-circuit the positive and negative terminals of the battery with wire or other metallic objects.

Do not transport or store the module with metallic items.

Do not expose the module to direct heat or flame, and do not use or store it near a fire or a location, subject to high

temperatures. In addition, do not immerse or dampen the module in water, saltwater, or any other liquid.

Do not puncture the module with any sharp objects, hit it with a hammering device or similar device, step on it, drop it or subject

it to strong shock.

Do not use module if it is damaged or deformed.

Immediately cease use of the module if it produces strange smells or smokes or becomes abnormally hot.

If the module fluids leak and come into contact with an eye, do not rub the eye and immediately flush it with plenty of water

before seeking medical assistance.

13. Notes

The pictures in the file are only for reference.

We reserve the final explanations of the items in this specification. This proposal is applicable for prototype.

Specifications subject to change without notice.

Shanghai Green Tech Co.Ltd.

No.5 Bibo Road Zhangjiang High Technology Park Pudong 201203 Shanghai,China

Tel:+86-21-50310528

E-mail: servic[email protected]

Https://www.greenteche.com

Dieses Handbuch passt für folgende Modelle

Andere GreenTech Stromversorgung Handbücher

GreenTech

GreenTech Capess Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung