Grizzly G5783 Bedienungsanleitung

Introduction

Drill in tight places with this 3⁄8" reversible angle

drill. Producing up to 1300 RPM, this angle drill

includes a 3⁄8" Jacobs® chuck and chuck key. The

large paddle switch also makes this drill easy to

use in any position. Requires 90 PSI of air pres-

sure with 7 CFM of compressor capacity.

Inventory

A. Angle Air Drill ............................................. 1

B. Chuck Key .................................................. 1

C. Hex Wrench 3mm ...................................... 1

Operation

Insert your drill bit up to 3⁄8" into the chuck and

tighten with the chuck key. Change the drill direc-

tion by pushing the reverse valve into the body

then rotate to lock into position. Connect the drill

to your regulated air source. The hex wrench is

included for removing the screw (Ref #55) that

holds the chuck to the spindle.

MODEL G5783

3⁄8" REVERSIBLE

ANGLE AIR DRILL

INSTRUCTION SHEET

Figure 1. Model G5783.

Figure 2. Lubricating directly into air fitting.

If you need help with your new pneumatic tool,

call our Tech Support at: (570) 546-9663.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#PC8322 PRINTED IN TAIWAN

INJURY HAZARD!

Always disconnect tool from

air to prevent unexpected

operation during service!

EYE/EAR INJURY HAZARD!

Wear safety glasses and

hearing protection during

use of this tool!

Air drill MUST have 3-4 drops of air tool oil directly

dropped into the air fitting before each use as

shown in Figure 2. Keep the head gear lubricated

by pumping a small amount light grease into the

ball cap on the head.

DO NOT EXCEED 120 PSI!

Personal injury could

occur.

G5783 Parts Breakdown and List













 

 



































  























 

 

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 P5783001 MOTOR HOUSING 34 P5783034 BALL BEARING

2 P5783002 AIR INLET 35 P5783035 LOCK RING

3 P5783003 DEFLECTOR 36 P5783036 INTERNAL GEAR

4 P5783004 STOP RING 37 P5783037 PLANET GEAR

5 P5783005 HOUSING CAP 39 P5783039 CAGE

6 P5783006 SCREW 39-1 P5783039-1 PIN

7 P5783007 LEVER 40 P5783040 SPACER

8 P5783008 SPRING PIN 41 P5783041 GEAR SPINDLE

9 P5783009 GASKET 42 P5783042 BALL BEARING

12 P5783012 VALVE SCREW 43 P5783043 PINION

13 P5783013 O-RING 44 P5783044 GEAR

14 P5783014 VALVE BUSHING 45 P5783045 ANGLE HOUSING

15 P5783015 THROTTLE VALVE 45-1 P5783045-1 BALL CAP

16 P5783016 O-RING 46 P5783046 BALL BEARING

18 P5783018 VALVE BUSHING 47 P5783047 RETAINER RING

20 P5783020 REVERSE RETAINER 48 P5783048 SPINDLE

21 P5783021 REVERSE BUSHING 49 P5783049 KEY

23 P5783023 REVERSE VALVE 50 P5783050 BALL BEARING

24 P5783024 REVERSE SPRING 51 P5783051 BEARING CASE

25 P5783025 BALL BEARING 52 P5783052 RETAINER RING

27 P5783027 GASKET 54 P5783054 SET SCREW

28 P5783028 REAR END PLATE 55 P5783055 SCREW

29 P5783029 CYLINDER 56 P5783056 CHUCK KEY

30 P5783030 ROTOR 57 P5783057 WAVE WASHER

31 P5783031 ROTOR BLADE 58 P5783058 CHUCK KEY

32 P5783032 MOTOR PIN 59 P5783059 3/8 DRILL CHUCK

33 P5783033 FRONT END PLATE 60 PAW03M HEX WRENCH 3MM

Andere Grizzly Bohren Handbücher

Grizzly

Grizzly G8595 Bedienungsanleitung

Grizzly

Grizzly T33901 Bedienungsanleitung

Grizzly

Grizzly H7827 Bedienungsanleitung

Grizzly

Grizzly C1393-96 Bedienungsanleitung

Grizzly

Grizzly G7945 Bedienungsanleitung

Grizzly

Grizzly G0484 Bedienungsanleitung

Grizzly

Grizzly G4008 Bedienungsanleitung

Grizzly

Grizzly G0485 Bedienungsanleitung

Grizzly

Grizzly G8597 1 /2-inch Bedienungsanleitung

Grizzly

Grizzly G3183 Bedienungsanleitung

Grizzly

Grizzly G0463 Bedienungsanleitung

Grizzly

Grizzly G9909 Bedienungsanleitung

Grizzly

Grizzly G7945 Bedienungsanleitung

Grizzly

Grizzly G0795 Bedienungsanleitung

Grizzly

Grizzly G9749 Bedienungsanleitung

Grizzly

Grizzly G1005Z Bedienungsanleitung

Grizzly

Grizzly G0705 Bedienungsanleitung

Grizzly

Grizzly G0704 Bedienungsanleitung

Grizzly

Grizzly G0485 Bedienungsanleitung

Grizzly

Grizzly H6194 Bedienungsanleitung

Grizzly

Grizzly G0619 Bedienungsanleitung

Grizzly

Grizzly G7947 Bedienungsanleitung

Grizzly

Grizzly G3358 Bedienungsanleitung

Grizzly

Grizzly H8217 Bedienungsanleitung

Beliebte Bohren Handbücher anderer Marken

Makita

Makita BDF456 Bedienungsanleitung

Black & Decker

Black & Decker LDX220 Bedienungsanleitung

Hitachi

Hitachi DH 40MA Bedienungsanleitung

Challenge

Challenge JO Technisches Referenzhandbuch

Makita

Makita LXFD01 Bedienungsanleitung

Festool

Festool T18+3 Bedienungsanleitung

Milwaukee

Milwaukee M12 FPDX-202X Bedienungsanleitung

EINHELL

EINHELL TE-RH 32 E Bedienungsanleitung

Makita

Makita DHP484 Bedienungsanleitung

Makita

Makita FD05 Bedienungsanleitung

Bosch

Bosch PSB 530 RA Bedienungsanleitung

Maximum

Maximum 054-1359-4 Bedienungsanleitung

Makita

Makita HP332D Bedienungsanleitung

Raider

Raider RDP-HD31H Bedienungsanleitung

Bort

Bort BPM-1400x2 Bedienungsanleitung

Black & Decker

Black & Decker 7266 Bedienungsanleitung

KENT USA

KENT USA TRD1230 Bedienungsanleitung

Bosch

Bosch GSB 19-2 RE Bedienungsanleitung