Grizzly G1690 Bedienungsanleitung

MITER TRIMMER

MODEL G1690

INSTRUCTION MANUAL

GRIZZLY IMPORTS, INC.

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM

WITHOUT THE WRITTEN APPROVAL OF GRIZZLY IMPORTS, INC,

REVISED NOVEMBER. 1993. PRINTED' IN USA

TABLE OF CONTENTS

I. INTRODUCTION 1

II. COMMENTARY 1

III. UNPACKING 2

IV. SAFETY RULES 2

V. INVENTORY 2

VI. CLEANUP 3

VII. OPERATION 4

VIII. CLOSURE 5

IX. MACHINE DATA 6

X. WARRANTY &RETURNS 7

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM

WITHOUT THE WRITTEN APPROVAL OF GRIZZLY IMPORTS, INC.

REVISED NOVEMBER, 1993. PRINTED IN USA

I. INTRODUCTION

We are proud to bring you the Model G1690 Miter Trimmer. The Model G1690 is part of

Grizzly's large family of fine woodworking tools and machinery. When used according to the

guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation

and proof of Grizzly's commitment to customer satisfaction.

The Model G1690 Miter Trimmer is an excellent choice for producing sharp, clean, accurate

miters on picture frames, molding, trim, and casement work. The Model G1690 can be mounted

to abench, or be moved from worksite to worksite.

We are also pleased to provide this instruction manual with the Model G1690 Miter Trimmer.

This instruction manual was written to guide you. through assembly, review safety consid-

erations and cover general operating procedures. It represents our latest effort to produce

the best documentation possible. If you have any constructive criticisms or comments that

you feel we should include in our next printing, please write to us at the address below.

Manager, Technical Documentation

Grizzly Imports, Inc.

P.O. Box 2069

Bellingham, WA 98227-2069

Finally, we stand behind our tools and machines. We have two excellent regional service

departments at your disposal should the need arise. If you have any service questions or

parts requests, please call or write to us at the appropriate location listed below.

If you live West of the

Mississippi River, contact:

P.O. Box 2069

Bellingham, WA 98227

Phone (206) 647-0801

If you live East of the

Mississippi River, contact:

2406 Reach Road

Williamsport, PA 17701

Phone (717) 326-3806

II. COMMENTARY

We would also like to state that the specifications and drawings in this manual represent

the Model G1690 as supplied when this manual was prepared. We are meticulous with our

manuals; however, product changes or discrepancies can occur. Whenever possible, we send

manual updates to all owners of aparticular tool or machine. Should you receive one, please

insert the new information with the old and keep it for reference.

-1 -

III. SAFETY RULES

There is acertain amount of danger associated with the use of this tool. Operating it with

respect and caution will considerably lessen the possibility of personal injury. If these safety

precautions are ignored, injury to the operator or others in the area could occur.

The Model G1690 was designed specifically as atrimming tool, not for general cutoff work.

Further, the trimmer should only be used on natural wood fibers, not on composites such

as plastics, particleboards, or MDF. This tool should never be modified or used for any other

purpose than that for which it was intended. As well as being dangerous, modifications or

improper use of the Model G1690 will void all warranties.

1.Never put your hands or fingers in the path of the blade. Keep fingers clear of the

cutting edge at all times.

2. Do not use your trimmer on wood of poor quality, or wood with nails.

3. Do not take too heavy aslice in one pass. Take several thin slices instead.

4. Contain long hair before using the trimmer.

5. Do not wear loose clothing, neckties, or jewelry during operation.

6. Make sure trimmer is secured to benchtop before use.

7. Lock fences and stops in position before use.

8. Keep blades sharp.

9. Use trimmer to cut wood fibers only. Composites, plastics, etc. will damage the knives.

10. Keep trimmer out of the reach of children.

IV. UNPACKING

Your trimmer arrived packaged in astiff cardboard box. If you find damage to the components

after you've signed the delivery receipt and the truck and driver have gone, you will need

to file afreight claim with the carrier. Save the container and all packing material for inspection

by the carrier or their agent. Without the packing material, filing afreight claim could be difficult.

Of course, if you ever need advice in this matter, please call us.

V. INVENTORY

The only loose part in the carton is the cast iron operating lever, which fits in the appropriate

slot on the geared wheel on the back of the trimmer. If anything is missing, call or write

to the appropriate regional service department listed in the Introduction. If anything is damaged,

please follow the procedures described in the "Unpacking" section.

Note: Be extremely careful when unpacking the trimmer. Keep fingers and hands clear of

the blade areas, should the blade slide freely during movement.

-2-

VI. CLEANUP

All of the unpainted surfaces of your machine have been treated with athick, brown rust

preventative to protect them from corrosion during shipment. The best way to remove this

substance is with common paint thinner (mineral spirits) and plenty of clean rags. Do not

use gasoline or other petroleum-based solvents because of their extremely low flash points.

Nor should you use chlorine-based solvents—if you happen to splash some onto apainted

surface, you'll ruin the finish. Before cleaning, please acknowledge the following safety rules

when working with solvents:

•Read and follow all directions and warnings on the solvent label.

•Work only in awell ventilated area.

•Do not work near any type of open flame (e.g., pilot lights, kerosene heaters, and

so on).

•DO NOT smoke while working with flammable material.

•Rags from the cleaning process are quite combustible. Dispose of waste towels so

they do not create afire hazard.

-3-

VII. OPERATION

If you have not already done so, secure the miter trimmer to atable or bench top. If you

need the trimmer to be portable, mount it to aplywood base, then clamp the base to astable

flat surface before use. If the trimmer is not secured, performace and safety could be

compromised.

The Model G1690 Miter Trimmer has two positive stops—one at 90° and another at 45°.

These stops are preset at the factory and are probably accurate. However, before you trim

an actual workpiece, test the angles on scraps first.

1. Crosscut apiece of scrapwood at 45° on atable saw or bandsaw. Then place the

workpiece in the trimmer and slice off about 1/32wof the end.

2. Using acombination square, measure the accuracy of the angle you have just cut.

In most cases, you shouldn't need to make an adjustment. But in case you do, minute

adjustments can be made by loosening the screw that holds the brass cam in place

on the trimmer's table.

3. Move the fence into the desired position by loosening the wing bolt and sliding the

fence left or right. Next, rotate the cam until it is snug against the fence.

4. Then tighten the cam's screw. Tighten the wing bolt.

5. Similarly, the spring pin at the 45° position can be adjusted to compensate for minor

inaccuracies. Simply rotate the cam to the desired position and tighten the stop in

place. Slide the fence over the pin (you might need to use asmall, flat-tipped

screwdriver to push the pin down while the fence clears it), and the spring will pull

the fence back against the pin to lock it in place at 45°. See Figure 1.

6. To set the fence to angles other than 45° or 90°, use abevel gauge to determine

the desired angle, then lock the fence in place against the bevel gauge.

Wing Bolt

Figure 1

-4-

7. Prepare the workpiece by accurately measuring the desired length needed. Add

approximately 7»" to either end and cut off, using atable saw, band saw, or machine

of your choice. Select the appropriate angle by moving the fence into place and

tightening the wing bolt on the end of the arm. Move the piece ahead so it hangs

over the edge of the bed by approximately Vaa".

8. Now, while keeping pressure on the workpiece simultaneously downward and against

the fence, draw the lever toward the workpiece with an even, steady force. You will

get better results by making several thin slices rather than one thick slice.

9. You can achieve compound miters by placing a45° block against the fence and resting

the workpiece against the block as shown in Figure 2.

Fence

45° Block

Figure 2

VIII. CLOSURE

The following pages contain general machine specifications, parts diagrams and lists, and

Warranty and Return information for your Model G1690 Miter Trimmer.

If you need parts or help in assembling your machine, or if you need operational information,

we encourage you to call the appropriate Regional Service Department. Our highly trained

service technicians will be glad to help you.

If you have any comments or concerns dealing specifically with this manual, please write

to our Bellingham, Washington location using the address listed in the Introduction.

-5-

IX. MACHINE DATA

GRIZZLY MODEL G1690 MITER TRIMMER

Overall Dimensions:

Height (Without Handle) 6M

Width 23"

Depth 9M

Capacity 3" x31

/2M

Knife Size ffl x 21

/4Mx5W

Cutting Angle Range -45° to +90°

Shipping Weight 28 lbs.

Net Weight 26 lbs.

Construction:

Base Cast Iron

Handle Cast Iron

Knives Carbon Tool Steel

Specifications, while accurate, are subject to change without notice.

-6-

X. WARRANTY &RETURNS

Limited Warranty

Grizzly Imports, Inc. (Grizzly) warrants every product it sells for aperiod of 90 days on all

parts and one year on all electric motors to the original purchaser from the date of purchase.

This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence,

accidents, repairs, alterations or lack of maintenance. This is Grizzly's sole written warranty

and any and all warranties that may be implied by law, including any merchantability or fitness,

for any particular purpose, are hereby limited to the duration of this written warranty. We

do not warrant or represent that the merchandise complies with the provisions of any law

or acts unless the manufacturer so warrants. In no event shall Grizzly's liability under this

warranty exceed the purchase price paid for the product and any legal actions brought against

Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental,

contingent, special or consequential damages arising from the use of our products.

To take advantage of this warranty, the product or part must be returned to either our

Bellingham or Williamsport warehouse, freight prepaid. Proof of purchase must accompany

the merchandise. The manufacturers reserve the right to change specifications at any time

as they constantly strive for better quality equipment.

We make every effort to ensure that our products meet high quality and durability standards

and we hope you never need to use this warranty.

-7-

Parts and Service Information

Grizzly stands behind its products with afull parts inventory. These parts are available for purchase by Grizzly machine

owners regardless of whether you are the original owner or asubsequent owner. If you are the original owner, please fill out

the warranty information on the warranty card, remove the card from this manual and send it back to us within 10 days of

product delivery. We appreciate any comments or suggestions and use them to better our products and service.

If you are not the original owner, please fill out one of the cards below, remove the card from the manual and send it

back to us. By registering with us, you will have the same access to parts and service as the original owner.

If you need service or help with this machine, please call or write to us at the appropriate regional service location listed

on page 1of this manual.

Original Owner

Name

Street

City_

CHANGE OF OWNERSHIP

Machine name &model no.

Phone Number.

State

ZIP. Date purchased.

New Owner

Name

Street.

City_

Phone Number.

State

ZIP. Date purchased.

Original Owner

Name

Street

City_

CHANGE OF OWNERSHIP

Machine name &model no.

Phone Number.

State

ZIP. Date purchased.

New Owner

Name

Street.

City.

Phone Number.

State

ZIP. Date purchased

Inhaltsverzeichnis

Andere Grizzly Trimmer Handbücher

Grizzly

Grizzly EKHS 500-45 2in1 Bedienungs- und Montageanleitung

Grizzly

Grizzly AHS 1852 Lion Bedienungs- und Montageanleitung

Grizzly

Grizzly EHS 4500 Bedienungs- und Montageanleitung

Grizzly

Grizzly ERT 3525 Bedienungsanleitung

Grizzly

Grizzly EHS 900 L Bedienungs- und Montageanleitung

Grizzly

Grizzly EHS 580-52 Bedienungs- und Montageanleitung

Grizzly

Grizzly ART 1825 Lion Bedienungs- und Montageanleitung

Grizzly

Grizzly ART 2420 Lion Bedienungs- und Montageanleitung

Grizzly

Grizzly EHS 500 T Bedienungsanleitung

Grizzly

Grizzly H0600 Bedienungsanleitung

Grizzly

Grizzly MTR 25 Bedienungs- und Montageanleitung

Grizzly

Grizzly ERT 230 Bedienungs- und Montageanleitung

Grizzly

Grizzly AHS 4055 Lion Set Bedienungs- und Montageanleitung

Grizzly

Grizzly EHS 600-61 R Bedienungs- und Montageanleitung

Grizzly

Grizzly BHS 2670 E2 Bedienungs- und Montageanleitung

Grizzly

Grizzly CH 1800 Li Bedienungs- und Montageanleitung

Grizzly

Grizzly ERT 450/8 Bedienungs- und Montageanleitung

Grizzly

Grizzly CT 1800 Li Bedienungsanleitung

Grizzly

Grizzly ET 3500 Bedienungs- und Montageanleitung

Grizzly

Grizzly AHS 4055 Lion Set Bedienungs- und Montageanleitung

Grizzly

Grizzly EHS 550 T Bedienungs- und Montageanleitung

Grizzly

Grizzly BHS 25 L Bedienungs- und Montageanleitung

Grizzly

Grizzly BHS 2660 AC E2 Bedienungs- und Montageanleitung

Grizzly

Grizzly AKHS 18-45 Bedienungs- und Montageanleitung

Beliebte Trimmer Handbücher anderer Marken

MTD

MTD HT 51 E Bedienungsanleitung

McCulloch

McCulloch T22 LS Bedienungsanleitung

COCKRAFT

COCKRAFT PRO HL36-S Bedienungsanleitung

Peco

Peco Z Trimmer ZT-3000 Bedienungsanleitung

Solo

Solo 116 Bedienungsanleitung

Stiga

Stiga ST 1200 Bedienungsanleitung

Echo

Echo GT-225 - 10-09 Bedienungsanleitung

RedMax

RedMax BT17 Bedienungsanleitung

GreenWorks

GreenWorks STA806 Bedienungsanleitung

Parkside

Parkside PHSL 900 A3 Bedienungsanleitung

Gardeo

Gardeo PRO GPTHT2560 Bedienungsanleitung

Park

Park DT-810870 Bedienungsanleitung

Worx

Worx WG209 Bedienungsanleitung

Gardenline

Gardenline 43671/HTKS26 Bedienungsanleitung

Makita

Makita 3710 Bedienungsanleitung

Champion

Champion 100683 Bedienungsanleitung

Stihl

Stihl FS 311 Bedienungsanleitung

Efco

Efco STARK 38 Handbuch