Grohe Red Mono 30 060 Bedienungsanleitung

D.....1 I.....5 N.....9 GR .....13 TR .....17 BG .....21 RO .....25

GB .....2 NL .....6 FIN .....10 CZ .....14 SK .....18 EST .....22 CN .....26

F.....3 S.....7 PL .....11 H.....15 SLO .....19 LV .....23 RUS .....27

E.....4 DK .....8 UAE .....12 P.....16 HR .....20 LT .....24

Design & Quality Engineering GROHE Germany

GROHE Red Mono

99.134.131/ÄM 223371/01.12

30 060

30 155

GB .....1 I.....5 N.....9 GR .....13 TR .....17 BG .....21 RO .....25

DK .....6 NL .....6 FIN .....10 CZ .....14 SK .....18 EST .....22 CN .....26

F.....3 S.....7 PL .....11 H.....15 SLO .....19 LV .....23 RUS .....27

E.....4 DK .....8 UAE .....12 P.....16 HR .....20 LT .....24

30 060

30 155

Please pass these instructions on to the end user of the fitting!

13mm *19 017

max.

60mm

max.

45mm

Ø8

10mm

4mm

Ø5mm

min. 50

4Ø40

Ø32

6 7

Type approvals

The GROHE Red boiling water storage heater

with filter

system must be installed with the safety assembly provided.

The boiling water storage heater

with filter system

may only be

operated together with an original GROHE Red boiling water

fitting.

Application

The boiling water storage heater is designed to heat and store

drinking water in pressurised systems. The boiling water

storage heater is suitable for connection to a mains system

with a maximum water pressure of 0.8 MPa (8 bar).

It must not be connected to hot water.

The filter system measures the flow rate using a sensor and

from this calculates the remaining capacity of the filter

cartridge as a function of the set litre capacity. If the filter

cartridge litre capacity set on the display unit is exceeded, the

values are displayed as negative values.

The sensor also monitors the maximum service life of the filter

cartridge. If the maximum service life of 12 months is

exceeded, the remaining capacity of the filter cartridge flashes.

The filter head is fitted with a type-tested non-return valve.

The water filtrate is classified as Category 2 according

to EN 1717.

Safety notes

GROHE Red boiling water storage heater:

This device is not intended for use by persons

(including children) with physical, sensory or mental

impairments or a lack of experience or knowledge in

using devices of this type.

Children must be supervised to ensure that they do

not play with the device.

Prevent danger resulting from damaged power

supply cables. In the event of damage, the boiling

water storage heater must be replaced by the

manufacturer or its customer service department or

an equally qualified person.

Caution, risk of scalding. Escaping water is boiling

hot. Never touch the end of the spout in order to

swivel the spout as it becomes extremely hot.

• The boiling water storage heater must be connected to

a permanent power supply with earth wire.

• Installation is only possible in frost-free rooms.

• The boiling water storage heater is only suitable for

indoor use.

• The boiling water storage heater must be placed in an

upright position.

• The boiling water storage heater and plug must not be

directly or indirectly sprayed with water when cleaning.

• The boiling water storage heater must not be opened.

•Useonly genuine replacement parts and accessories.

The use of other parts will result in voiding of the warranty

and the CE identification, and could lead to injuries.

If the boiling water storage heater is to be drained (for any

reason), the safety assembly of the boiling water storage

heater must be removed. Invert the boiling water storage

heater and allow the water to run out.

However, we strongly advise against draining the boiling

water storage heater. There is a significant risk of

damaging the boiling water storage heater.

Filter system:

To avoid health risks, please note the following

information when using the filter system:

• For hygiene reasons, the filter system must be flushed

before using for the first time, see section Installation.

• For optimum filter cartridge performance, the set litre

capacity or the service life of 12 months must not be

exceeded.

• The filter head must be replaced after 5 years.

• The filter system may only be operated with cold water of

foodstuff grade.

• At the installation location, the filter system must be

protected from mechanical damage, heat and direct

sunlight.

• Following storage and transport at temperatures below 0 °C,

the filter cartridge must be stored in its opened original

packaging at ambient temperatures of 4 – 30 °C for at

least 24 hours before use.

• The filter system must never be opened when in operation.

• The filter material in the filter cartridge is specially treated

with silver. It is possible that a small amount of silver, which

is completely safe, may be released into the water. The

amount is in keeping with the recommendations of the World

Health Organisation (WHO) for drinking water.

• Notice for people suffering from kidney disease or on

dialysis:

Filtering may result in a slight increase in the potassium

content. If you are suffering from kidney disease or are

on a low-potassium diet, we recommend that you

consult your doctor.

• GROHE recommends not leaving the filter system out of

service for extended periods of time. If the filter system is

not used for more than 4 weeks, at least one storage heater

fill (4 litres) must be discharged and discarded.

Technical data

Electrical data

Boiling water storage heater:

• Connection: Wall socket with earth wire, protected

via a 13 A fuse

• Voltage supply: 230 V AC / 50 Hz

• Power consumption: 2100 W

• Standby power loss (switched on): 15 W

• Standby power loss (switched off): 1 W

• Type of protection: IPX4

Filter system:

• Sensor battery: 3 V lithium battery (type CR 2032)

• Cable length: 1,500mm

• Display unit rating (wall installation): IPX4

• Sensor rating: IPX8

Sanitary data

Boiling water storage heater, fitting:

• Boiling water storage heater capacity: 4 l

• Flow pressure:

– min. 0.05 MPa (0.5 bar)

– recommended 0.1 – 0.5 MPa (1 – 5 bar)

• Operating pressure: max. 0.8 MPa (8 bar)

• Test pressure: 1.6 MPa (16 bar)

• Flow rate at 0.3 MPa (3 bar) flow pressure: approx. 3.7 l/min

• Boiling water temperature 99 °C

The actual temperature may differ slightly due to different

ambient pressures

• Heating time from 10 °C to 99 °C: approx. 15 min

• Available storage heater volume at 99 °C: 3 l/min

• Max. chlorine value: 100 mg/l

• Water connection to storage heater:

Cold water from service valve

• Water connection at fitting:Boiling water from storage heater

Filter system:

• Water temperature: 4 – 30 °C

• Flow rate at 3 bar flow pressure: approx. 4.5 l/min

• Filter capacity at 14 - 17 °KH: 600 l

or max. 12 months

The relevant water supplier can provide information on the

carbonate hardness and chlorine value.

New Water Regulations

Please ensure installation complies with New Water Regula-

tions. It must also be installed in accordance with local bye-law

requirements.

Approval and conformity

The conformity declarations can be obtained from the following

address:

GROHE Deutschland Vertriebs GmbH

Zur Porta 9

D-32457 Porta Westfalica

Electrical installation

Electrical installation work must only be

performed by a qualified electrician. This work

must be carried out in accordance with the

regulations according to IEC 364-7-701-1984

(corresponding to VDE 0100 Part 701) as well as

all national and local regulations.

• Extension cables are not permitted between the electrical

socket and boiling water storage heater connection.

Installation

Refer to the dimensional drawing on fold-out page I.

Installing fitting, see fold-out page II, Figs. [1] and [2].

Insert fitting in sink hole. This will require leading through the

hoses one at a time.

Note: If there is no need to fit support plate (A), the clamping

length may be increased by 15mm, see Fig. [1].

Mount safety relief valve kit to the waste pipe, see Figs. [3]

to [7].

Mount wall holder to the wall, see Fig. [8] and [9].

Screw the expansion vessel (B) to the safety

assembly (C), see Fig. [10].

Fix expansion vessel (B) with safety assembly (C) to the

wall holder, see Fig. [11].

Install wall holder (D), see Fig. [12].

Use suitable screws and if applicable wall plugs (not included

in the scope of delivery).

Set water hardness at filter head (E), see Fig. [13].

Set water hardness at bypass setting (F) to local conditions,

see table column A on page 5. The relevant water supplier can

provide information on the water hardness. The value from

column B assigned to the bypass value from column A must

also be set on the display unit (G), see section Setting the

litre specification.

Insert filter head (E) in wall holder (D), see Fig. [13].

Insert filter cartridge (H), see Fig. [14].

Filter head (E) can be swivelled forwards by up to 90° in wall

holder (D) to install the cartridge.

Remove protective cover (H1) and insert filter cartridge (H)

into filter head (E) to the stop. Note the installation position of

the filter cartridge.

Turn locking handle (E1) until filter cartridge is felt to lock into

place.

Install pressure hose (I) at inlet [IN] of filter head (E),

see Fig. [15].

Install sensor (J) at outlet [OUT] of filter head (E),

see Fig. [15].

Important: Note direction of flow.

The sensor (J) must be installed horizontally.

Install display unit (G), see Fig. [15].

Use suitable screw and if applicable wall plug or secure using

double-sided adhesive tape (not included in the scope of

delivery).

This product conforms to the requirements of the

relevant EU guidelines.

Install storage heater taking into consideration the

available hose lengths, see Figs. [2] and [16].

Do not connect voltage supply yet.

Flush pipes thoroughly before and after installation

(observe EN 806).

Connect filter system, see Fig. [2] and [16].

1.Screw pressure hose (I) of filter system onto service valve,

see Fig. [16].

2.Screw hose (L) onto sensor (J).

Connect safety assembly (C), see Fig. [2] and [16].

1.Screw hose (L) to safety assembly (C) using the seals

provided, see Fig. [16].

2.Secure storage heater pressure hose (M) marked blue to

safety assembly (C) using the seals provided.

3.Connect copper pipe (not in the scope of delivery) to

the Ø15mmcompression connection of the drain

device (C1).

Connecting fitting, see Figs. [2] and [16].

- Connect the fitting pressure hose (N) marked 99 °C to

connection (N1) on the storage heater, see Fig. [11].

The spout must not be fitted with any downstream

resistances in the form of air bubblers (e.g. mousseurs) or

components reducing flow (e.g. restrictors) as these will

result in damage to the storage heater.

Open the service valve and check connections for

watertightness.

Flush filter system, see fold-out page III, Fig. [17].

1.Place collecting vessel under filter to collect water flowing

out of hose (O).

2.Press flush valve (E2) on filter head (E) and flush filter

system.

3.Continue flushing until water emerging from hose (O) is

clear and free of bubbles [min. 2 litres].

Filling storage heater with water, see Figs. [18] and [19].

1.Pull button (P1) on handle (P) of fitting outward and turn the

handle anti-clockwise, see Fig. [18].

2.Fill the storage heater until water comes out the spout of

the fitting.

3.Connect voltage supply via mains plug (R), see Fig. [19].

- Press and hold button (S) on storage heater for at

least 2 seconds to switch on the storage heater. The red

indicator lamp (S1) indicates that the storage heater is

switched on.

4.Open the GROHE Red boiling water fitting and flush with

one storage heater fill (4 litres).

Setting the litre specification

The bypass setting (F) set in the filter head (E), see fold-out

page II, Fig. [8], must be transferred to the display unit (G), see

fold-out page III, Fig. [20].

The value for the litre specification must be set as follows

depending on the water hardness as per table column B on

page 5:

The GROHE Red boiling water system is now fully

installed and ready for operation.

Operating the fitting

Note:

In order to prevent incorrect operation and for protection

against injury, we recommend affixing the sticker provided.

Pull button (P1) on handle (P) outward and turn and hold

handle (R) anti-clockwise to draw boiling water. Handle (R)

closes automatically, see Fig. [18].

Press and hold button (S) for at least 2 seconds to switch the

storage heater on or off, see Fig. [19].

Button Display

Briefly press PROG button

(PRG flashes)

Briefly press RESET button to access

programming for litre specification

(00000flashes)

Keep pressing PROG button until

required position is reached

(00000 digit flashes)

Keep pressing RESET button until

required digit is reached

(00600 digit flashes)

Keep pressing PROG button to exit

menu (PRG disappears and set value

appears)

The date of installation must be noted on the

maintenance sticker and affixed at a visible location

on the storage heater.

Maintenance

In the case of interventions in the mains supply

or maintenance work, the GROHE Red boiling

system must be bled as steam jets could

otherwise occur.

Close the service valve, switch off the storage heater and

disconnect the mains plug.

Wait until the storage heater and fitting have cooled down.

Open the lever to depressurise the storage heater.

Inspect and clean all parts, replace as necessary and lubricate

with special grease.

Filter (H), see fold-out page III, Fig. [21].

See technical product information enclosed with the filter

cartridge for information on replacing the filter.

The filter system is equipped with the 600 litre filter cartridge

(Prod. No.: 40 404) at the factory. The following filter sizes are

also available. 3,000 litre filter cartridge (Prod. No.: 40 412)

or 1,500 litre filter cartridge (Prod. No.: 40 430).

Note: The various filter cartridges can be ordered at

www.grohe.com.

Resetting the filter capacity, see fold-out page IV, Fig. [22].

After a new filter cartridge is inserted, the filter capacity must

be reset as follows:

Note: The litre specification programmed for the filter cartridge

is retained.

Battery (G3), see fold-out page IV, Fig. [23] and [24].

The battery must be replaced 7 years after commissioning the

fitting, at the latest.

1.Loosen screw (G1) and remove cover (G2), see Fig. [23].

2.Remove battery (T) and replace, see Fig. [24].

Important: Note correct polarity.

Note: No settings saved by the user will be lost when

changing the batteries or if the battery discharges.

Assemble in reverse order.

II. Mousseur

Remove and clean mousseur (13 999), see fold-out page I.

Assemble in reverse order.

Service

In order to improve customer service, we recommend

registering the product under www.grohe.com.

Note the Fault/Cause/Remedy table for information on

eliminating problems.

If the problem cannot be rectified, disconnect the mains plug to

shut off the voltage supply. Note down the serial number of the

storage heater on the rear of the device and get in touch with

GROHE Customer Service or contact the GROHE Service

Hotline under TechnicalSuppor[email protected].

The GROHE Red boiling water storage heater cannot be

repaired. If servicing is required, the complete storage heater

must be replaced.

In order to ensure correct operation, maintenance must be

performed on all hot-water-bearingpartsby GROHE Customer

Service every five years.

Following any service/maintenance work, the boiling water

storage heater must be re-filled, see section Installation.

Replacement parts

See fold-out page I (* = special accessories).

Care

For directions on the care of this fitting, please refer to the

accompanying Care Instructions.

Disposal

Button Display

Display flashing

(negative litre specification, e.g. -1 or

remaining capacity e.g. 150 flashing)

Press RESET button for 3 seconds

(rESEt appears)

The data for time and litre capacity is

reset

Button Display

BATT display flashes

(battery is discharged and needs to be

replaced)

The date of maintenance must be noted on the

maintenance sticker on the storage heater.

This category of devices does not belong in the

domestic waste, but must be disposed of

separately in accordance with the relevant local

national regulations.

Carbonate hardness Bypass Litre capacity 40 404

12 - 13 (°KH) 21 - 24 (°fH) 4,10 - 4,82 (mval/l) 2,06 - 2,41 (mmol/l) 50 % 900 l

14 - 17 (°KH) 25 - 31 (°fH) 4,83 - 6,25 (mval/l) 2,42 - 3,12 (mmol/l) 40 % 600 l

18 - 24 (°KH) 32 - 43 (°fH) 6,26 - 8,75 (mval/l) 3,13 - 4,37 (mmol/l) 30 % 400 l

25 - 35 (°KH) 44 - 63 (°fH) 8,76 - 12,50 (mval/l) 4,38 - 6,24 (mmol/l) 20 % 250 l

Fault Cause Remedy

Water too cold • Empty storage heater switched on

(‘On’ indicator lamp flashes)

• Heating phase not yet complete

- Fill the storage heater, see section Installation

Reset the storage heater by pressing the reset

button (U) located onthe rear of the storageheater

using a thin object, see Fig. [25]

- Wait max. 15 minutes

Flow rate too low • Fitting mousseur dirty or defective

• Isolating valve not fully open

• Water supply restricted

- Replace mousseur, see section Maintenance

- Fully open shut-off valves, isolating valves

- Check supply lines, open isolating valve

Water not boiling • Storage heater not hot enough yet - Wait approx. 15 minutes after switching on

Storage valve losing

water • Hose connection or internal tank leaking - Switch off the storage heater, disconnect the mains

plug and contact GROHE Customer Service

Splashy, irregular

spray • Fitting mousseur dirty or defective - Replace mousseur, see section Maintenance

Fitting running

continuously • Handle not closing - Close the isolating valves, switch off the storage

heater, disconnect the mains plug and contact

GROHE Customer Service

Dieses Handbuch passt für folgende Modelle

Andere Grohe Kessel Handbücher

Grohe

Grohe RED 40 701 Bedienungsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung