Groov-e GV-TT03 Bedienungsanleitung

GV-TT03

MUSIC CENTRE

CD/MP3 PLAYER WITH TURNTABLE

STEREO RADIO AND USB ENCODING

INSTRUCTION MANUAL

IMPORTANT SAFETY INSTRUCTIONS:

1.Read the instructions. All uses guidelines must be read before start device.

2. Keep the instructions for future use.

3.Attention, use and security guidelines must be respected.

4. The device must not be used near water or be put in contact with moisture.

5. Make sure has no liquid is spilled on device and device openings.

6. Move device carefully, avoid shocks.

7. Do not block the breakdown of the device outputs.

8. Do not place the device near from a heat source (e.g. radiator). Do not expose it to the Sun.

9. Plug the device as indicate on this information form.

10. This device has a connection with overload protection (security device) decision-making. If the

replacement of decision-making is required, please you send has an experienced or the device

manufacturer technician.

11. For cleaning the device, please follow the recommendations of the notice.

12. The sector cord should be unplugged a long period of use.

13. Device shall be repaired by a qualified person when:

a. the taken or the power cord is damaged,

b. objects have falleninto the apparatus or a liquid has been spilled into device,

c. device was exposes to the rain,

d. device does not work correctly without notable exterior change,

e. device fell and the subwoofer is broken.

14. The user shall not try to maintain device beyond that which is described in this information

form. The guarantee would negate.

BATTERY INSTALLATION

The battery compartment is located on the back of the remote control.

1. Remove the battery compartment door by pressing in on the tab and lifting it off.

2. Insert two (2) AAA size batteries (not included) into the battery compartment following the

polarity markings inside the battery compartment.

3. Replace the battery compartment door.

Battery Precautions

Replacement of batteries must be done by an adult.

Do not mix old and new batteries.

Do not mix alkaline, standard (carbon-zinc) or rechargeable

(nickel-cadmium) batteries.

The supply terminals are not to be short-circuited.

Non-rechargeable batteries are not to be recharged.

Exhausted batteries are to be removed.

Only batteries of the equivalent type are to be used.

Batteries are to be inserted with the correct polarity.

Dispose of batteries properly. Do not dispose of batteries in fire. The

batteries may explode or leak.

LOCATION OF CONTROLS

1) DUST COVER

2) DIAL POINTER

3) LEFT SPEAKER

4) LCD DISPLAY

5) FM STEREO LED INDICATOR

6) REMOTE SENSOR

7) CD DOOR

8) USB SOCKET

9) VOLUME KNOB

10) X-BASS CONTROL BUTTON

11) RECORD BUTTON

12) REPEAT/INTRO/RANDOM BUTTON

13) RIGHT SPEAKER

14) TUNING KNOB

15) CD DOOR OPEN BUTTON

16) SOURCE BUTTON

17) FM MODE SELECTOR

18) POWER OFF/FUNCTIONS SELECTOR

19) 3.5 MM HEADPHONE JACK

20) CD PLAY/PAUSE/STOP BUTTON

21) CD SKIP UP /DOWN BUTTON

22) MP3 FOLDER UP BUTTON

23) SPINDLE ADAPTOR

24) TURNTABLE SPEED SELECTOR

25) AUTO STOP SWITCH

26) PICK-UP HOLDER

27) LINE OUT SOCKET

28) FM ANTENNA

29) AC CORD

CAUTION:

USAGE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULTE IN HAZARDOUS RADIATION EXPOSURE.

THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE

PERSONNEL.

PRECAUTIONS FOR USE

INSTALLATION

UNPACK ALL PARTS AND REMOVE PROTECTIVE MATERIAL.

DO NOT CONNECT THE UNIT TO THE MAINS BEFORE CHECKING THE MAINS VOLTAGE AND BEFORE

ALL OTHER CONNECTIONS HAVE BEEN MADE.

DO NOT COVER ANY VENTS AND MAKE SURE THAT THERE IS A SPACE OF SEVERAL CENTIMETERS

AROUND THE UNIT FOR VENTILATION.

CONNECTION

1. CONNECT THE POWER CORD (29) TO AC OUTLET

2. SWITCH THE FUNCTION SELECTOR (18) TO “TUNER “ FUNCTION. IF THE BACKGROUND OF DIAL SCALE

LIGHT UP WITH AMBER LIGHT, IT’S MEAN THE POWER SUPPLY IS NORMAL. NOW YOUR SYSTEM IS

READY TO PLAY THE MUSIC.

LISTENING TO RADIO

MANUAL TUNING

1. SWITCH THE FUNCTION SELECTOR (18) TO “ TUNER “ FUNCTION.

2. TUNE TO THE REQUIRED STATION BY TURNING THE TUNING KNOB (14).

3. ADJUST VOLUME KNOB(9) TO THE DESIRE VOLUME LEVEL.

FM & FM-STEREO RECEPTION

SET THE FM MODE SELECTOR (17) AT “ FM ” POSITION. PROGRAMS ARE RECEIVED IN MONO MODE. IN

PARTICULAR WHEN STEREO SIGNAL ARE WEAK. IT IS PREFERABLE TO RECEIVE THE PROGRAM IN

MONO.

SET THE FM MODE SELECTOR (17) AT “FM-ST” POSITION FOR RECEIVING STEREO PROGRAMS. THE

FM-STEREO LED INDICATOR (5) WILL LIGHT UP TO SHOW FM STEREO PROGRAM IS RECEIVING.

HINTS FOR BEST RECEPTION:-

- FM : THE RECEIVER HAS A BUILT-IN FM WIRE ANTENNA HANGING AT THE REAR CABINET. THIS WIRE

SHOULD BE TOTALLY UNRAVELED AND EXTENDED FOR BEST RECEPTION.

PLAYING COMPACT DISC

GETTING START

1. TURN FUNCTION SELECTOR(18) TO SELECT “ CD/USB ” MODE.

2. PRESS “OPEN/CLOSE” BUTTON (15) TO OPEN THE CD DOOR (7).

3. PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN CLOSE THE CO DOOR.

4. FOCUS SEARCH IS PERFORMING, THE LCD DISPLAY (4) WILL SHOW THE TOTAL NUMBER OF TRACKS &

TOTAL PLAYING TIME.

PLAY / PAUSE / STOP MODE

1. PRESS THE “PLAY/PAUSE/STOP” BUTTON (20) TO START PLAYBACK, THE FIRST TRACK WILL START

PLAYBACK.

2. TO INTERRUPT, PRESS THE “PLAY/PAUSE/STOP” BUTTON (20) ONCE, THE PLAYING TIME WILL BE

FREEZE & FLASHING ON THE LCD DISPLAY (4). PRESS AGAIN TO RESUME NORMAL PLAYBACK.

3. IF PRESS AND HOLD THE “ PLAY / PAUSE STOP “ BUTTON (20) FOR OVER 2 SECONDS DURIGN

PLAYBACK MODE. THESYSTEM WILL GO TO STOP MODE.

SKIP/SEARCH MODE (SKIP/SEARCH UP / SKIP/SEARCH DOWN )

1. DURING PLAY OR PAUSE MODE, IF “SKIP UP” BUTTON (3) IS PRESSED. IT WILL GO TO NEXT TRACK AND

DISPLAY THE TRACK NO. AND THEN REMAIN THE PLAY OR PAUSE MODE.

2. DURING PLAY OR PAUSE MODE, IF “SKIP DOWN” BUTTON (3) IS PRESSED. IT WILL GO BACK TO THE

BEGINNING OF THE TRACK, ORIGINAL TRACK NO. IS DISPLAY AND REMAIN THE PLAY OR PAUSE MODE.

3. AFTER STEP 2, PRESS “SKIP DOWN” BUTTON (3) AGAIN WILL GO TO THE PREVIOUS TRACK AND

REMAIN THE PLAY OR PAUSE MODE.

4. IF PRESS AND HOLD THE “ SKIP UP/DOWN BUTTON “ (3) DURING CD/MP3 PLAYABCK, THE PLAYING

TRACK WILL GO FAST FORWARD OR BACKWARD UNTIL THE BUTTON BEING RELEASED.

FOR MP3 DISC

1. PRESS “ FOLDER “ BUTTON (22), THE FOLDER NO. WILL GOES UP

2. PRESS “ SKIP UP “ OR SKIP DOWN (21) BUTTON, THE TRACK NO. CHANGE.

3. WHEN THE DESIRED TRACK IS BEING SELECTED, PRESS THE CD “PLAY/PAUSE/STOP ” BUTTON (20) TO

START PLAYBACK.

ID3 (TRACK/ALBUM TITLE) FUNCTION (BY REMOTE HANDSET)

1. PRESS THE “ INFO“ BUTTON DURING PLAYBACK OF MP3/WMA DISC, THE SONG TITLE IS BEING

DISPLAYED. PRESS THE “ INFO ” BUTTON AGAIN TO DISABLE THE FUNCTION.

MP3 TRACK FORMAT REQUIREMENT:-

- MP3 BIT RATE : 32 KBPS~256 KBPS.

- THE PERFORMANCE OF PLAYING MP3 DISC IS VARIOUS FROM THE QUALITY OF RECORDING DISC AND

THE METHOD OF RECORDING. FURTHERMORE, THE SEARCHING LEAD-TIME FOR MP3-CD IS LONGER

THAN NORMAL CD DUE TO DIFFERENCE FORMAT.

REPEAT/INTRO/RANDOM MODE

PRESS THE REPEAT/INTRO/RANDOM BUTTON BEFORE OR DURING PLAYBACK, A SINGLE TRACK, SINGLE

FOLDER (MP3 ONLY) OR ALL THE TRACKS CAN BE PLAYED IN DIFFERENCE MODE AS FOLLOW:-

FOR CD

(1) REPEAT 1 (2) REPEAT ALL TRACK (3) INTRO (4) RANDOM (5) OFF MODE

INDICATOR

PLAY MODE ON LCD DISPLAY

REPEAT TRACK

REPEAT ALL ALL

INTRO INTRO

RANDOM RANDOM

OFF MODE --------------

FOR MP3 DISC

(1) REPEAT 1 (2) REPEAT ALLTRACKS (3) REPEAT 1 FOLDER

(6)OFFMODE (5)RANDOM (4) INTRO PLAY

INDICATOR

PLAY MODE ON LCD DISPLAY

REPEAT SINGLE TRACK

REPEAT ALL TRACKS ALL

REPEAT SINGLEFOLDER

INTRO PLAY MODE INTRO

RANDOM MODE RANDOM

OFF MODE -----------------

REPEAT PLAY

YOU CAN LISTEN TO THE DESIRED TRACKS OR FOLDER REPEATEDLY BY THIS FUNCTION.

INTRO PLAY (BY REMOTE CONTROL)

YOU CAN LISTEN THE BEGINNING (10 SECONDS) OF EACH TRACK IN A CD BY THIS FUNCTION & SAVING

YOUR TIME TO SEARCH THE DESIRE SONG

RANDOM PLAY

YOU CAN LISTEN ALL THE TRACKS OR FOLDER IN A RANDOM ORDER BY THIS FUNCTION

CD DISC PROGRAMMING (BY REMOTE CONTROL)

UP TO 32 TRACKS CAN BE PROGRAMMED FOR CD FILE AND PLAY IN ANY ORDER. BEFORE USE, BE SURE

THE SYSTEM IS AT STOP MODE BEFORE PROGRAMMING:-

1. SET IN CD/USB MODE & STOP THE CD PLAYBACK.

2. PRESS THE “PROGRAM” BUTTON, “ PROG“ WILL APPEAR ON LCD DISPLAY (4).MOREOVER, IT WILL

INDICATE PROGRAM NO. AND DIGITS FOR TRACK NO. TO BE PROGRAMMED.

3. SELECT A DESIRED TRACK BY PRESSING SKIP OR BUTTONS (21).

4. PRESS THE“ PROGRAM ” BUTTON TO STORE THE TRACE INTO MEMORY.

5. REPEAT STEPS 3 AND 4 TO ENTER ADDITIONAL TRACKS INTO THE MEMORY IF NECESSARY.

6. WHEN ALL THE DESIRED TRACKS HAVE BEEN PROGRAMMED, PRESS CD “ PLAY/PAUSE/STOP ”

BUTTON (20) TO PLAY THE DISC IN ASSIGNED ORDER.

7. TO CANCEL THE PROGRAMMED FILE, PRESS “STOP” BUTTON ON REMOTE HANDSET UNTIL “ PROG “ IS

DISAPPEAR ON LCD DISPLAY (4)

PLAYBACK OF MP3 SONG VIA USB STORAGE MEDIA

CONNECTING

THE SYSTEM IS ABLE TO DECODE AND PLAYBACK ALL MP3FILE WHICH STORED IN THE MEMORY MEDIA

WITH USB CONNECTING PORT.

1. SET FUNCTION SELECTOR (18) AT CD/USB MODE AND THEN PRESS

SOURCE BUTTON (16) TO SELECT “ USB ” MODE.

2. PLUG-IN THE USB PLUG WITH THE FACE UP & MAKE SURE IT GOING

INTO COMPLETELY. INSERT STRAIGHT WITHOUT BENDING.

CONNECTING THE USB UPSIDE DOWN OR BACKWARDS COULD

DAMAGE THE AUDIO SYSTEM OR THE STORAGE MEDIA. CHECK TO BE

SURE THE DIRECTION IS CORRECT BEFORE CONNECTION.

3. THE SYSTEM WILL START READING THE STORAGE MEDIA

AUTOMATICALLY AFTER CONNECTING, AND LCD DISPLAY (4) WILL

SHOW THE TOTAL NUMBER OF MP3 FILES AND TOTAL NUMBER OF

FOLDER BEING DETECTED.

4. REPEAT THE SAME PLAYBACK PROCEDURE AS PLAYING CD/MP3 DISC

AS ABOVE

REMARK

- THE SYSTEM CAN DETECT AND READ THE FILE UNDER MP3FORMAT

ONLY THOUGH THE USBPORT.

- IF CONNECT THE SYSTEM TO MP3 PLAYER VIA THE USB SOCKET, DUE TO VARIANCES IN MP3

ENCODING FORMAT, SOME MP3 PLAYER MAY NOT BE ABLE TO PLAY VIA THE USB SOCKET. THIS IS

NOT A MALFUNCTION OF THE SYSTEM.

ENCODING OF CD/PHONO INTO MP3 FILE

THE SYSTEM IS ABLE TO ENCODE NORMAL CD OR TURNTABLE TO MP3 FORMAT AND RECORDING AT

MEMORY MEDIA WITH USB CONNECTING PORT.

A) CD ENCODING

I) ECNODING 1 TRACK

1. PERFORM NORMAL PLAYBACK OF THE CD TRACK YOU WANT TO ENCODE & RECORD,

2. PRESS “ REC “ BUTTON (11) DURING THE PLAYBACK OF THE DESIRE TRACK, UNIT WILL DISPLAY “

“&“ “ AND FLASHING. ENCODING IS PERFORMING NOW.

3. AFTER COMPLETING OF ENCODING, UNIT WILL STOP PLAYBACK AUTOMATICALLY.

II) ENCODING 1 DISC – TO RECORD A WHOLE CD

1. PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN CLOSE THE CD DOOR

2. STOP THE PLAYBACK BY PRESSING THE ONCE AND THEN AGAIN TO STOP CD

COMPLETELY. THE NUMBER OF TRACKS ON THE CD WILL DISPLAY.

3. PRESS THE “ REC “ BUTTON (11) AFTER FOCUS SEARCH COMPLETED.UNIT WILL DISPLAY “

“&“ “ AND FLASHING. ENCODING IS PERFORMING NOW.

4. AFTER COMPLETING OF ENCODING, UNIT WILL STOP PLAYBACK AUTOMATICALLY.

III) ENCODING BY PROGRAM

1. PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN CLOSE THE CD DOOR

2. SELECT THE DESIRE TRACKS BY FOLLOWING “CD DISC PROGRAMMING“ PROCEDURES. THEN

PRESS “ CD PLAY/PAUSE/STOP “ BUTTON (20) TO START PLAYBACK.

3. DURING CD PLAYBACK, PRESS AND HOLD THE “ CD PLAY/PAUSE/STOP “ BUTTON (20) FOR 2

SECONDS TO ENTER THE STOP MODE.

4. PRESS THE “ REC “ BUTTON (11) AND THE UNIT WILL DISPLAY “ “&“ “& FLASHING. ENCODING

IS PERFORMING NOW.

5. AFTER COMPLETING OF ENCODING, UNIT WILL STOP PLAYBACK AUTOMATICALLY.

REMARK:-

- THE RECORDING SPEED IS 1:1 AND ACCORDING TO THE ACTUAL PLYING TIME OF THE CD TRACK

- THE SYSTEM WILL CREAT A “ AUDIO “ FOLDER AND THEN STORE THE ENCODING TRACK IN IT.

- THE RECORDING FORMAT IS PRESET AT – MP3 BIT RATE : 128 KBPS, SAMPLING RATE : 44.1KHZ

- NO SONG TITLE WILL BE RECORDED DURING ENCODING MODE

- TO INTERRUPT THE RECRODING, PRESS THE “RECORD“ BUTTON AGAIN DURING RECORD MODE

- RECORDING WILL BE COMPLETED ONLY ENTIRE SONG BEING ENCODED, IF TERMINATED THE

ENCODING PROCESS INTERMEDIATELY, THERE IS NO TRACK BEING RECORDED NOR STORED TO

THE USB.

IV) COPYING OF MP3 FILE

IF PUTTING A MP3 DISC INSTEAD OF A CD-DISC, THE SYSTEM WILL COPY THE FILES TO THE USB IF PRESS

THE “ REC “ BUTTON. THE OPERATION PROCEDURES IS SAME AS CD ENCODING AS STIPULATE ON ABOVE,

AND THE SYSTEM WILL SWITCH TO COPYING MODE ONLY IF MP3 FILE BEING READ.

B) PHONO ENCODING

1) SET THE FUNCTION BUTTON TO “ PHONO “ MODE AND THEN PRESS THE “ REC “ BUTTON DIRECTLY.

2) THE LCD DISPLAY WITH SHOW THE WORD “ USB “ AND THEN FLASHING, AND THEN DISPLAY “

“ & “ “ AND FLASHING AFTER FEW SECONDS. NOW THE SYSTEM IS STARTING THE ENCODING

MODE.

3) START PLAYBACK AT PHONO FOR THE TRACK WHICH YOU WANT TO RECORD TO USB.

4) AFTER FINISH OF RECODING, PRESS AND HOLD THE “REC“ BUTTON (11) UNTIL THE LCD STOP

FLASHING AND RETURN TO “ PHONO “ MODE.

C) ENCODING BITRATE (BY REMOTE HANDSET)

YOU CAN SELECT THE DESIRED BITRATE DURING ENCODING FROM CD OR PHONO TO USB, THE

SELECTABLE RANGE FROM 32 / 64 /96 /128 / 192 / 256 KBPS.

1) SET IN “PHONO “FUNCTION(18)&REMAIN STOP MODE.

2) PRESS THE “ INFO “ FUNCTION AND THE LCD DISPLA WILL SHOW THE DEFAULT BITRATE (128 KBPS)

3) PRESS SKIP OR BUTTONS (21) TO SELECT THE DESIRED BITRATE FOR ENCODING.

4) PRESS AGAIN THE “ INFO “ TO CONFIRM THE SETTING AND THE LCD DISPLAY (4) RESUME TO “ PHONO

“ MODE

D)TRACK SEPARATION (BY REMOTE HANDSET)

YOU CAN DIVIDE THE RECORDING MUSIC FROM PHONO TO USB/SD TRACK BY TRACE DURING ENCODING.

EVERY TIME WHEN PRESS THE “ “ (TRACK SEPARATION) BUTTON ONCE AT REMOTE HANDSET DURING

ENCODING FROM PHONO TO USB/SD, THE SYSTEM WILL GENERATE A NEW TRACK AND CONTINUOUS THE

RECRODING. THE TEXT “ PHONO “ AT LCD DISPLAY WILL FLASHING ONE TIME, IT MEAN THE UNIT IS

CREATING A NEW TRACK SUCCESSFULLY.

FILE DELETE AT USB/SD CARD (BY REMOTE CONTROL)

THE SYSTEM IS ABLE TO ERASE THE FILE STORED INSIDE THE USB PEN DRIVE OR SD CARD BY

FOLLOWING:-

A) SINGLE FILE DELETE

1．PRESET AT “ USB “ OR “ SD “ MODE.

2．PRESS AND HOLD THE “ INFO “ BUTTON FOR 3 SECONDS AND THE LCD DISPLAY (4) WILL SHOW (DEL

---001)

3．PRESS SKIP FORWARD OR SKIP BACKWARD BUTTON TO SELECT THE FILE GOING TO DELETE

4．PRESS THE “ REC “ BUTTON TO ENTER “ YES / NO “ MODE AND THEN PRESS SKIP FORWARD OR

SKIP BACKWARD TO SELECT “ YES “ OR “ NO “.

5．PRESS THE “ REC “ BUTTON AGAIN TO CONFIRM THE SETTING.

B) ALL FILES DELETE

1. PRESET AT “ USB “ OR “ SD “ MODE.

2. PRESS AND HOLD THE “ INFO “ BUTTON FOR 3 SECONDS AND THE LCD DISPLAY (4) WILL SHOW (DEL

---001)

3. PRESS AND HOLD THE “ INFO “ BUTTON TO ENTER “ YES / NO “ MODE AND THEN PRESS SKIP

FORWARD OR SKIP BACKWARD TO SELECT “ YES “ OR “ NO “.

4. PRESS THE “ REC “ BUTTON AGAIN TO CONFIRM THE SETTING.

REMOVING OF USB / MEMORY CARD

TO REMOVE THE USB, TURN OFF THE POWER OR SWITCH THE FUNCTION MODE TO EITHER CD OR TUNER

FIRST. FOR USBPORT – UN-PLUG IT BY PULLING OUT THE USB SOCKET DIRECTLY.

PHONO

NOTED:

-REMOVE THE STYLUS PROTECTOR.

-BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM

REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.

1. SELECT TO “ PHONO ” FUNCTION FROM FUNCTION SELECTOR (18)

2. SET THE SPEED SELECTOR TO THE PROPER POSITION DEPENDING ON THE RECORD TO BE PLAYED.

3. PLACE THE RECORD ON THE PLATTER (USE THE SPINDLE ADAPTOR IF REQUIRED).

4. LIFT THE TONE ARM FROM THE REST AND SLOWLY MOVE IT TO THE RECORD

SIDE. THE PLATTER WILL START TO ROTATE.

5. PLACE THE TONE ARM TO THE DESIRED POSITION OF THE RECORD.

6. ADJUST THE VOLUME TO THE DESIRED LEVEL.

7. AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING.

LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE REST.

8. TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO

THE REST.

REMARK : AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT SETTING, SO IT WILL

STOP BEFORE THE LAST RACK FINISH. IN THIS CASE, SELECT THE AUTO-STOP SWITCH (26) TO “ OFF

“ POSITION, THEN IT WILL RUN TO THE END OF THE RECORD BUT WILL NOT STOP AUTOMATICALLY (TURN

OFF THE UNIT BY POWER BUTTON OR SWITCH BACK THE AUTO-STOP SWITCH TO “ ON “ POSITION TO

STOP THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE REST POSITION.

LINE OUT CONNECTION

YOU CAN CONNECT THE SYSTEM TO YOUR WHOLE HI-FI SYSTEM BY CONNECTING THE LINE OUT SOCKET

(27) TO THE AUXILIARY INPUT SOCKET WITH A RCA CABLE (NOT INCLUDED).

REMOTE CONTROL TRANSMITTER

CONTROL FUNCTIONS

BATTERY INSTALLATION (BATTERY NOT PROVIDED)

THE INFRA-RED TRANSMITTER REQUIRES 2 PC AAA SIZE BATTERY FOR OPERATION

BUTTON DESCRIPTION

1) OPEN/CLOSE PRESS TO OPEN OR CLOSE THE CD DOOR IN CD

MODE

2) INFO IN CD/PHONO STOP MODE, PRESS TO SELECT

ENCODING BITRATE

3) REC IN CD OR PHONO MODE, PRESS TO ACTIVE

RECRRDING FUNCTION

4) REP/INTRO/RAN IN CD/USB MODE, PRESS TO ACTIVE REPEAT /

INTRO / RANDOM FUNCTION

5) PROGRAM IN CD/USB MODE, PRESS TO ACTIVE

PROGRAMMING FUNCTION

6) PLAY/PAUSE IN CD/USB MODE, PRESS ONCE TO START

PLAYBACK. PRESS AGAIN TO ENTER PAUSE MODE.

7) SKIP/SEARCH FORWARD PRESS ONCE TO SKIP TO NEXT TRACK, PRESS &

HOLD FOR SEARCH FORWARD

SKIP/SEARCH BACKWARD PRESS ONCE TO SKIP TO PREVIOUS TACK.PRESS &

HOLD FOR SEARCH BACKWARD

8) STOP IN CD/USB MODE, PRESS TO STOP PLAYBACK OR CANCEL THE STORED

PROGRAM.

9) FOLDER UP /DOWN IN MP3 MODE, PRESS TO SELECT FOLDER UP OR DOWN

10) SOURCE IN CD/USB MODE, PRESS TO SELECT CD OR USB FUNCTION REPEATLY

CARE AND MAINTENANCE

1. Avoid operating your unit under direct sunlight or in hot, humid or dusty places.

2. Keep your unit away from heating appliances and sources of electrical noise such as fluorescent lamps

or motors.

3. Unplug the unit from the electrical power outlet immediately in case of malfunction.

CLEANING THE UNIT

To prevent fire or shock hazard, disconnect your unit from the AC power source when cleaning.

The finish on the unit may be cleaned with a dust cloth and cared for as other furniture, Use caution

when cleaning and wiping the plastic parts.

If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any wax or polish sprays on

the cabinet.

If the front panel becomes dirty or smudged with fingerprints it may be cleaned with a soft cloth

slightly dampened with a mild soap and water solution. Never use abrasive cloths or polishes as

these will damage the finish of your unit.

CAUTION: Never allow any water or other liquids to get inside the unit while cleaning.

SPECIFICATION

AC POWER AC 230V ~ 50Hz

RADIO FREQUENCY FM 87.5 – 108 MHz

TURNTABLE 33 1/3, 45 RPM

OUTPUT POWER 2 X 1.5W RMS

NOTE: Due to ERP stage two requirements and to protect the environment, the

unit will switch to standby mode automatically if no is music playing after 15

minutes.

INSTRUCTIONS ON ENVIRONMENT PROTECTION

DO NOT DISPOSE OF THIS PRODUCT IN THE USUAL HOUSEHOLD WASTE AT THE END OF ITS LIFECYCLE,

HAND IT OVER AT A COLLECTION POINT FOR THE RECYCLING OF ELECTRICAL AND ELECTRONIC

APPLIANCES. THE SYMBOL ON THE PRODUCT, THE INSTRUCTIONS FOR USE OR THE PACKING WILL

INFORM THEM ABOUT THE METHODS FOR DISPOSAL. THE MATERIALS ARE RECYCLABLE AS INDICATED

BY THE SYMBOL ON THE LEFT.

BY RECYCLING, MATERIAL RECYCLING OR OTHER FORMS OF RE-UTILIZATION OF OLD APPLIANCES, YOU

ARE MAKING AN IMPORTANT CONTRIBUTION TO PROTECT OUR ENVIRONMENT. PLEASE CONTACT YOUR

LOCAL COUNCIL FOR THE AUTHORIZED DISPOSAL LOCATION AND RECYCLING FACILITIES.

Unit J, Braintree Road

Braintree Industrial Estate

Ruislip

Middlesex HA4 0EJ

www.groov-e.co.uk

Ver. 1

Inhaltsverzeichnis

Andere Groov-e Stereoanlage Handbücher

Groov-e

Groov-e GVSP480 Bedienungsanleitung

Beliebte Stereoanlage Handbücher anderer Marken

LG CM3330B Bedienungsanleitung

Sony

Sony SS-CEP50 Bedienungsanleitung

Cetacea Sound

Cetacea Sound CVS-II Bedienungsanleitung

Aiwa

Aiwa XR-H66MD Bedienungsanleitung

Denon

Denon UCD-250 Bedienungsanleitung

Sanyo

Sanyo DC-MX41i Bedienungsanleitung

Sharp

Sharp CD-ES600V Bedienungsanleitung

Exibel

Exibel BDX600-UK Bedienungsanleitung

Sanyo

Sanyo DC-F320 Bedienungsanleitung

Philips

Philips FWM583X Bedienungsanleitung

Sharp

Sharp CD-C462 Bedienungsanleitung

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio Bedienungsanleitung

Aiwa

Aiwa XR-EM70 Bedienungsanleitung

Cyrus

Cyrus Lyric Bedienungsanleitung

Philips

Philips MCM159/98 Bedienungsanleitung

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C Bedienungsanleitung

RCA

RCA RS3965SB Bedienungsanleitung

Sharp

Sharp XL-UH240 Bedienungsanleitung