Grozone Control OSWDN Bedienungsanleitung
www.grozonecontrol.com
USER GUIDE
OSWDN
Day/Night ON/OFF Switcher
TABLE OF CONTENTS
SAFETY NOTICE 3
GENERAL DESCRIPTION 4
TYPICAL USE 4
SPECIFICATIONS 4
OPERATION AND OPTIONAL SETTING 5
SETTING THE DAY-NIGHT LEVEL 5-6
WARRANTY & CUSTOMER SERVICE 7-8
3
3
SAFETY NOTICE
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
DANGER
TO REDUCE T E RISK OF FIRE OR ELECTRIC S OCK,
CAREFULLY FOLLOW T ESE INSTRUCTIONS.
To reduce the risk of electric shock, disconnect power to the 120V
electrical outlet before installing or removing the unit. When removing the
electrical wall plate, it may fall across plug pins or become displaced.
To reduce the risk of electric shock, this product has a grounding type plug
that has a third (grounding) pin. This plug will only fit into a grounding
type power outlet. If the plug does not fit into the outlet, contact a
qualified electrician to install the proper outlet. Do not change the plug in
any way.
3
4
4
GENERAL DESCRIPTION
4
The OSWDN On/Off switcher features two 120V outputs to supply
power to equipment either during the day only or during the night only.
This plug-in module is similar to Grozone OSW except that OSW Trigger
Cord has been removed and replaced by a photocell; therefore, the On/
Off outputs are controlled by day-night conditions, instead of being con-
trolled by a voltage applied to the trigger cord.
TYPICAL USE
1– For DAY/NIGHT C ntr l : if you need to control your equipment during
the DAY or during the NIG T only, then plug your equipment as follows:
- In the upper output to turn the equipment «On during the DAY ONLY»
- In the lower output to turn the equipment «On during the NIG T ONLY»
2– TO FIX a DAY/NIGHT Detecti n Pr blem : you can also use this module
to connect a controller without a photocell, or a controller having problem
detecting day or night conditions correctly in the grow room : the OSWDN
has a day-night sensitivity level setting that allows you to define the
amount of light needed to detect a day or a night condition meeting your
specific grow room conditions.
SPECIFICATIONS
•
Two 120V outputs : upper output is ON while lower output is OFF
and vice versa.
•
Total current for both outputs : 15A maximum.
•
Photocell in a clear plastic dome to allow light detection 360°.
•
Day-night level setting on the side of the module, to set the pho-
tocell sensitivity to your grow room conditions.
•
ETL LISTED
5
OPERATION AND OPTIONAL SETTING
5
OPERATION AND OPTIONAL SETTING
Just plug your equipment into the top or bottom plug and you’re set!
Your equipment will toggle ON or OFF as soon as the lights in your room
will switch ON or OFF.
Grozone OSWDN photocell sensitivity is factory set for proper Day-
Night detection. If the DAY-Night detection works just fine in your grow
room, do not touch to the DAY-NIG T LEVEL SETTING. If the DAY-NIG T
detection is not properly set, read the instructions below.
The user can m dify the ph t cell sensitivity t perate in a DARK
DAY r a CLEAR NIGHT c nditi n.
•
What is a DARK DAY c nditi n? A dark day condition is met when
the light level during the day is darker than factory set day level.
This situation may occur if your module is connected as the bot-
tom of a wall in a dark section of your grow room or in the
shadow of larger equipment. In this case, the controller may not
detect day condition even though the lights are on in the grow
room.
SETTING THE DAY-NIGHT LEVEL
Example : Your CO2 controller stops enriching your room with CO2 dur-
ing the day, because it detects a NIG T condition, even though your
lights are still lit in the room! You’re probably experiencing a Dark DAY
condition...
•
What the CLEAR NIGHT c nditi n? A clear night condition is met
when the light level during the night is brighter than factory set
night level. This situation may occur if some light leaks coming
from doors or windows prevent your controller to detect a real
night condition, even though the lights are in the grow room.
Example : Your CO2 controller keeps enriching CO2 day and night, be-
cause it detects a DAY condition even though your lights are OFF in the
room! You’re probably experiencing a CLEAR NIG T condition...
(↓
↓↓
↓)
(↑
↑↑
↑)
6
SETTING THE DAY-NIGHT LEVEL
SETTING THE OSWDN IN A DARK DAY CONDITION
Your are in a DARK DAY condition : the photocell sensitivity is too low to
detect enough light to switch the upper output ON during the day. Using a
small screwdriver, rotate the DAY-NIG T LEVEL SETTING “COUNTER
CLOCKWISE” until the upper utput supplies 120V. Terminate the setting
by rotating further a few more degrees in the same direction. Turn the
lights ON and OFF in your grow room to validate the setting : the load
connected to the upper output should turn on when the lights are on in
the room.
SETTING THE OSWDN IN A CLEAR NIGHT CONDITION
Your are in a CLEAR NIG T condition : the photocell sensitivity is too high
and detecting low amount of light that inappropriately switches the upper
output ON during the night. Using a small screwdriver, rotate the DAY-
NIG T LEVEL SETTING “ CLOCKWISE” until the l wer utput supplies
120V. Terminate the setting by rotating further a few more degrees in the
same direction. Turn the lights on and off in your grow room to validate
the setting: the load connected to the lower output should turn on when
the lights are off in the room.
ON / OFF SWITCHER
ON during the DAY
OFF during the NIGHT
_____________________________________________________________
ON during the NIGHT
OFF during the DAY
Day-Night
Level Setting
Photocell in a 360° dome
7
7
WARRANTY & CUSTOMER SERVICE
DO YOU AVE A PROBLEM WIT YOUR CONTROLLER ? PLEASE READ
THESE INSTRUCTIONS CAREFULLY AND SAVE THEM FOR FUTURE
REFERENCE.
1. I think my c ntr ller is damaged, r it simply d es n t w rk as
indicated in the user guide, what sh uld I d ?
•
Please refer to the troubleshooting steps. Follow these instructions
carefully, step by step. The controller should work as described in the
“Expected results” column of the Complete Troubleshooting Guide.
D y u need assistance n executing the Tr ublesh ting steps?
1. C ntact us at 1-855-262-1800
2. Send us an EMAIL at service@gr z nec ntr l.c m
3. VISIT ur Technical Supp rt Center at
www.gr z nec ntr l.c m/techsupp rt.html
Technical Support is available Monday through Friday, from 8:00 AM
to 8:00 PM, Eastern Time.
7
8
2. I’ve been thr ugh the tr ublesh ting steps. What d I d if I meet a
pr blem at any f these steps? Is my pr duct c vered by the
WARRANTY?
•
Grozone controllers are covered by a 3-year warranty (*). We will
replace any DAMAGED PRODUCT WIT A BRAND NEW PRODUCT.
•
Covered or not covered? We do not authorize the replacement of fully
working products nor altered (tampered) products. The Troubleshooting
steps will help you identify a damaged product. Do not hesitate to
contact us or contact your retailer to make sure the controller is not fully
working or damaged before returning it to the store.
•
My product is not fully working or damaged, I want a replacement unit:
in order to get a replacement product, y u MUST return all m dules
and applicable access ries t the retailer. To avoid being charged for
the accessories, be sure to include all pieces. Thanks for your
cooperation.
•
Any Grozone Control product that is returned with obvious signs of user
neglect will not be covered by the warranty. Grozone Control exercises
the right to make final decisions in these matters.
(*)
The warranty period begins from the date of purchase at the retail level. The
retailer/consumer must keep their proof of sale/purchase. Otherwise, Grozone
Control will consider the manufacturing date to apply the warranty coverage.
IMPORTANT MESSAGE TO RETAILERS
Retailers must call Grozone Control to get authorisation to replace the
defective product and a RMA number.
1-855-262-1800
WARRANTY & CUSTOMER SERVICE
8
NOTE
Inhaltsverzeichnis
Sprachen:
Andere Grozone Control Schalten Handbücher
