Grundfos CIM 260 Bedienungsanleitung

CIM 260 and CIM 280

Cellular modules

Installation and operating instructions

CIM 260/280

Installation and operating instructions

Other languages

http://net.grundfos.com/qr/i/99440283

GRUNDFOS INSTRUCTIONS

CIM 260 and CIM 280

English (GB)

Installation and operating instructions ..................................4

Deutsch (DE)

Montage- und Betriebsanleitung .....................................15

Dansk (DK)

Monterings- og driftsinstruktion ......................................27

Español (ES)

Instrucciones de instalación y funcionamiento............................38

Suomi (FI)

Asennus- ja käyttöohjeet ..........................................50

Français (FR)

Notice d'installation et de fonctionnement...............................61

Italiano (IT)

Istruzioni di installazione e funzionamento ..............................72

Português (PT)

Instruções de instalação e funcionamento ..............................84

한국어 (KO)

설치 및 작동 지침 ...............................................95

Appendix A..................................................105

EU declaration of conformity .....................................106

UK declaration of conformity.....................................109

Table of contents

English (GB) Installation and operating instructions

Original installation and operating instructions

Table of contents

1. General information ............. 4

1.1 Hazard statements .............. 4

1.2 Notes ..................... 4

2. Product introduction ............ 5

2.1 Applications .................. 5

2.2 LEDs ..................... 6

3. Receiving the product............ 7

3.1 Inspecting the product ............ 7

4. Installation requirements .......... 7

4.1 Security .................... 7

4.2 RF safety ................... 8

4.3 Antenna requirements ............ 8

4.4 Radio frequency radiation exposure

information (for Canada and US only) .... 8

4.5 EMC statements for USA ........... 9

5. Mechanical installation ........... 9

5.1 Fitting a cellular antenna ........... 9

5.2 Inserting the SIM card ............10

6. Electrical connection ............10

6.1 Connecting the battery and power supply ..10

6.2 Connecting the battery ............10

6.3 Connecting the power supply.........11

7. Fault finding .................12

7.1 CIM 260 or CIM 280 fitted in a Grundfos

product ....................12

7.2 CIM 260 or 280 fitted in the CIU unit .....13

8. Technical data ................14

9. Disposing of the product ..........14

1. General information

Read this document before you install the

product. Installation and operation must

comply with local regulations and accepted

codes of good practice.

1.1 Hazard statements

The symbols and hazard statements below may

appear in Grundfos installation and operating

instructions, safety instructions and service

instructions.

DANGER

Indicates a hazardous situation which, if

not avoided, will result in death or serious

personal injury.

WARNING

Indicates a hazardous situation which, if

not avoided, could result in death or

serious personal injury.

CAUTION

Indicates a hazardous situation which, if

not avoided, could result in minor or

moderate personal injury.

The hazard statements are structured in the following

way:

SIGNAL WORD

Description of the hazard

Consequence of ignoring the warning

• Action to avoid the hazard.

1.2 Notes

The symbols and notes below may appear in

Grundfos installation and operating instructions,

safety instructions and service instructions.

Observe these instructions for explosion-

proof products.

A blue or grey circle with a white graphical

symbol indicates that an action must be

taken.

A red or grey circle with a diagonal bar,

possibly with a black graphical symbol,

indicates that an action must not be taken

or must be stopped.

If these instructions are not observed, it

may result in malfunction or damage to the

equipment.

Tips and advice that make the work easier.

English (GB)

2. Product introduction

2.1 Applications

CIM 260 or CIM 280 cellular module (CIM =

Communication Interface Module) enable data

transmission between a cellular network and a

Grundfos product.

CIM 260 communicates using Modbus TCP via

cellular data transmission to a SCADA system or

SMS communication to mobile phones.

CIM 280 communicates via cellular network to the

related cloud, for example, Grundfos iSolutions

Cloud, (requires a Grundfos contract).

In the following, "Grundfos product" means one or

more Grundfos products, depending on the actual

application.

CIM 260 and CIM 280 cellular module make it

possible to control and monitor a Grundfos product in

several ways:

• From a SCADA system via a data connection.

• From a mobile phone via SMS messages. See the

manual "CIM 260 SMS commands".

• From Grundfos iSolutions Cloud or the related

cloud where control takes place via a central

server. This is not described in this document.

CIM 260 or CIM 280 is supplied separately and must

be fitted in the product to be communicated with or in

a CIU unit (CIU = Communication Interface Unit).

Retrofitting of CIM 260 or CIM 280 is described in the

installation and operating instructions of the Grundfos

product.

If you want CIM 280 to connect to another

cloud than Grundfos iSolutions Cloud, for

example, Grundfos Remote Management,

it can take 3-4 minutes until the interface

reconnects at first communication process.

2.1.1 CIM 260 or CIM 280 cellular module

3 4 5 7 6

TM084023

CIM 260 or CIM 280 cellular module

English (GB)

Pos. Designation Description

1 Battery socket

2 SIM card holder

3Secondary SMA connection for cellular antenna1)

4Primary SMA connection for cellular antenna.

This antenna must always be connected.

5 LED1 Yellow and green status LED for cellular communication.

6 LED2 Red and green status LED for internal communication between CIM 260 or CIM 280

and the Grundfos product.

7 SW1

For CIM 260:

To reset to factory settings, press and hold for at least 5 seconds.

For CIM 280:

To reset CIM 280, press and hold for 1 second.

To reset to factory settings, press and hold for at least 5 seconds.

1) Only use this antenna connection if required by the telecom company.

2.2 LEDs

CIM 260 and CIM 280 cellular module have two

LEDs.

• Yellow and green status LED (LED1) for cellular

communication

• Red and green status LED (LED2) for internal

communication between CIM 260 or CIM 280 and

the Grundfos product.

LED1 (yellow and green)

1 second

3 seconds

A B

TM084022

LED1 status

Pos. Description

1 Searching for cellular network

2 Cellular network active

3Data exchanged via data connection2)

4 Sending SMS message

A Yellow

B Green

2) Only applies to CIM 260.

LED1 status

Pos. LED1 status Description for CIM 260 Description for CIM 280

1 Flashing yellow. Searching for a cellular network. Searching for a cellular network.

2 Pulsating yellow (single pulse). Connection to the cellular

network has been established.

Connection to the cellular

network has been established.

3 Pulsating green (single pulse). Data are exchanged via data

connection. -

4 Green (3 sec.). Sending an SMS message. Sending an SMS message.

LED2 status

English (GB)

LED2 status Description for CIM 260 Description for CIM 280

Off CIM 260 has been switched off. CIM 280 has been switched off.

Flashing red.

No internal communication

between CIM 260 and the Grundfos

product.

After commissioning, the LED2 will flash red if the

communication to the Grundfos product is lost.

Permanently red. CIM 260 does not support the

Grundfos product.

The product driver is not downloaded from Grundfos

Remote Management (GRM) or Grundfos iSolutions

Cloud (GiC) yet. When the CIM 280 is switched on, the

LED2 may turn green for one minute before it turns

permanently red.

Permanently

green.

Internal communication between

CIM 260 and the Grundfos product

is OK.

Internal communication between CIM 280 and the

Grundfos product is OK.

During startup, it may take up to 5 seconds

to update the LED2 status.

Related information

2.1.1 CIM 260 or CIM 280 cellular module

3. Receiving the product

3.1 Inspecting the product

Before installing the product, do the following:

1. Check that the product is as ordered.

2. Check that no visible parts have been damaged.

3. If parts are damaged or missing, contact your

local Grundfos sales company.

4. Installation requirements

WARNING

Electric shock

Death or serious personal injury

‐Before starting any work on the

product, make sure that the power

supply has been switched off and that

it cannot be accidentally switched on.

‐SELV wires must not come into contact

with other wires with higher voltages.

QR99462331

QR code for the CIU quick guide

4.1 Security

Grundfos connected products must be behind a

firewall or connected to a private network.

If a firewall or private network is not in place, the

Grundfos product may be subject to a cyber-security

risk and becomes vulnerable to an attack or

compromise.

Follow the highly recommended configuration

requirements below. If in doubt, consult an IT

Infrastructure Specialist.

4.1.1 CIM 260, cellular

The CIM 260 modules are cellular-based modules

and require cellular connectivity through a private

Access Point Name (APN) to be securely connected

English (GB)

to the Internet. Any basic cellular connectivity solution

is not recommended, only private APNs are

recommended.

The private APN must be purchased from your mobile

network operator. The mobile network operator will

guide you through the setup process.

TM077057

Secure connectivity for CIM 260

Pos. Description

1 Grundfos device

2 Private APN

3 Private mobile network

4 Firewall

5 Internet

4.2 RF safety

Installers and end users must be provided

with these installation and operating

instructions and operating conditions for

satisfying RF exposure compliance.

WARNING

Radiation

Minor or moderate personal injury

‐The antenna used for the product in

which the CIM module is fitted must be

installed to provide a separation

distance of at least 20 cm (0.66 feet)

from persons and must not be co-

located or operated in conjunction with

any other antenna or transmitter.

Interference of other electronic equipment may occur

if the equipment is inadequately protected.

4.3 Antenna requirements

WARNING

Radiation

Death or serious personal injury

‐The combined gain of the cable-

antenna solution used for this product

must not exceed 2.0 dBi (800, 900,

1800, 2100, 2600 MHz).

4.4 Radio frequency radiation exposure

information (for Canada and US only)

This equipment complies with FCC and ISED

radiation exposure limits set forth for an uncontrolled

environment. This equipment must be installed and

operated with a minimum distance of 20 cm (0.66

feet) between the radiator and your body.

This transmitter must not be co-located or operated in

conjunction with any other antenna or transmitter.

Model: CIM 280-US

TM071660

The host product needs to be labelled

with:

HMN name:______________________

Contains FCC ID: OG3-CIM2X0-3G-4G

Contains IC: 10447A-CIM2X034G.

The enclosed FCC label must be attached near the

barcode label on the product in which the CIM

module is installed. Remember to write the host

marketing name (HMN) on the label according to the

table.

Type on the product

nameplate

HMN name for the FCC

label

MAGNA3 MAGNA3 Z

MLE71 MLE71 Z

MLE80 MLE80 Z

MLE90 MLE90 Z

English (GB)

Type on the product

nameplate

HMN name for the FCC

label

MLE100 MLE100 Z

MLE112 MLE112 Z

MLE132 MLE132 Z

MLE160 MLE160 Z

This device complies with Part 15 of the

FCC Rules.

Operation is subject to the following two

conditions:

1. This device may not cause harmful interference,

and

2. This device must accept any interference

received, including interference that may cause

undesired operation.

Changes or modifications made to this

equipment not expressly approved by

Grundfos may void the FCC authorisation

to operate this equipment.

4.5 EMC statements for USA

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there

is no guarantee that interference will not occur in a

particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the

interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

5. Mechanical installation

5.1 Fitting a cellular antenna

The antenna for CIM 260 or CIM 280 must be

connected to the module to establish connection to

the cellular network.

Connect the antenna cable to the SMA connection

(pos. 1) of CIM 260 or CIM 280. The antenna must be

installed outside the control cabinet in a position with

good reception conditions. If required by the telecom

company, connect an additional antenna.

TM084024

Fitting an external cellular antenna

Pos. Description

Primary SMA connection for the cellular

antenna.

This antenna must always be connected.

2Secondary SMA connection for the cellular

antenna3)

3) Only use this antenna connection if required by the telecom

company.

English (GB)

5.2 Inserting the SIM card

Before inserting the SIM card into CIM 260 or CIM

280, remove the PIN code, or set it to "4321".

1. Insert the SIM card into a mobile phone.

2. Remove the PIN code from the SIM card, or set it

to "4321". See the manual of the mobile phone.

3. For CIM 280, you must have a SIM

card subscription with international

SMS roaming activated.

Insert the SIM card into CIM 260 or CIM 280.

The slanted edge of the SIM card must

point downwards.

TM084025

Inserting the SIM card

Pos. Description

1 SIM card holder

2 SIM card

6. Electrical connection

6.1 Connecting the battery and power

supply

WARNING

Electric shock

Death or serious personal injury

‐Connect CIM only to a Grundfos host

product with a dedicated CIM interface.

‐Installation must be carried out by

qualified and trained experts.

WARNING

Flammable material

Death or serious personal injury

‐The safety precautions listed below

must be observed carefully as

improper handling of the lithium-ion

battery may result in injury or damage

from electrolyte leakage, heating

ignition or explosion.

These safety precautions must be observed:

• Only insert the approved Grundfos battery pack

(99465650).

• Never use this battery pack in other battery

chargers.

• Do not dismantle or modify the battery.

• Do not heat or incinerate the battery.

• Do not pierce, crush or cause mechanical damage

to the battery.

• Do not short circuit the battery.

• Do not allow the battery to get wet or be

immersed in water.

• Do not strike or throw the battery.

• For long periods of storage, the storage

temperature should be below +35 °C.

6.2 Connecting the battery

The CIM 260 and CIM 280 cellular module can be

fitted with a lithium-ion battery, part number

99465650. It is secured by a velcro strap which

absorbs vibrations and makes it easier to replace the

battery. Connect the battery to CIM 260 or CIM 280

as shown below. See the CIU quick guide for

placement of the battery on the CIU cover.

If the battery is not connected, the user will

not receive any information in case of a

power cut.

English (GB)

Andere Handbücher für CIM 260

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Grundfos Steuereinheit Handbücher

Grundfos

Grundfos CIM 500 Bedienungsanleitung

Grundfos

Grundfos CIM 500 Bedienungsanleitung

Grundfos

Grundfos Unilift AP12 Bedienungsanleitung

Grundfos

Grundfos CIM 260 Bedienungsanleitung

Grundfos

Grundfos LC 23 Series Betriebsanleitung

Grundfos

Grundfos BMS Series Betriebsanleitung

Grundfos

Grundfos PM TWIN Bedienungsanleitung

Grundfos

Grundfos CIM 280-US GIC Gen2 Bedienungsanleitung

Grundfos

Grundfos DIT-IR Bedienungsanleitung

Grundfos

Grundfos CIM 290-MA LPWAN GiC Bedienungsanleitung

Grundfos

Grundfos CIM 500 Bedienungsanleitung

Grundfos

Grundfos BM Bedienungsanleitung

Grundfos

Grundfos LC 241 Bedienungsanleitung

Grundfos

Grundfos TP Bedienungsanleitung

Grundfos

Grundfos CIM 270 Bedienungsanleitung

Grundfos

Grundfos CIM 1 Series Bedienungsanleitung

Grundfos

Grundfos CU 401 Bedienungsanleitung

Grundfos

Grundfos IO 242 Bedienungsanleitung

Grundfos

Grundfos CMB-SP Booster PM2 Bedienungsanleitung

Grundfos

Grundfos CIM 260 Bedienungsanleitung

Grundfos

Grundfos CIM 100 Bedienungsanleitung

Grundfos

Grundfos CIM 260 Bedienungsanleitung

Grundfos

Grundfos MP 204 Bedienungsanleitung

Grundfos

Grundfos G 401 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung