GSM Activate e-CO Series Bedienungsanleitung
Page 1
MODEL ECO DOOR V2
GSM 2G & 3G
Door Contact Alarm
e-CO RANGE
Product Information
Our 2G/3G GSM Door Contact Alarm is a standalone alarm system for smaller rooms
inside properties. It will alert you using GSM technology by sending you a text message
and/or phone call to your mobile phone or landline when the sensor has been broken
alerting you to a possible intrusion.
The unit is enclosed in a IP65 rated box which means it is perfectly weathered for outside
installation and has passed testing in high temperature as well as below freezing
temperatures.
GSM Module Specification
●GSM Frequency: Quadband Freq 850/900/1800/1900 - 3G Model 2100 Mhz
●Power Supply Voltage: 9-24 Volts DC - 1 Amp Min
●Current Used in Standby Mode: 60mA Max
●IP65 Rated Enclosure for Outside Installation
●Micro 2G or 3G Simcard
●No Landline Required
●Dimensions - L100 x W68 x H50mm
●Dimensions PCB Only - L95 x W67mm
●Sim Active Function
●Operating Temperature: -10…+40°C
●Programmed by Text Message
●Text to Test Signal Strength
●Wireless Range to Door Contact 25 Feet
Door Contact Specification
●Alert Distance: 25-35mm separation
●Detection: Duel Function, Magnetic Door and Emergency Switch
●Battery Life: 6 Months
●Dimensions - L60 x W32 x H13mm
www.gsm-activate.co.uk - 01273462380 - [email protected]
Page 2
Page 3
Instructions
IMPORTANT- PLEASE READ
Please make sure you disconnect the power when you fit the simcard. Then slide the
simcard into the holder making sure that the clipped corner of the simcard lines up with
the clipped corner of the simcard holder as seen in the image above.
Signal Strength
To help ensure that you place the unit in a suitable position you can text the unit to see
how much signal strength the detector is receiving by texting the command,
#SIGNAL#
The detector will perform a test on the signal strength.
You will receive a text confirming the signal strength between 0 up to 30. We strongly
recommend that you place the unit where it can receive a signal of at lease 10. Anything
less than this will make the unit unreliable.
SIM Active Function
Our GSM Auto Dialler comes with a SIM Active function meaning that it will send a
message every six weeks to a preprogrammed number we at GSM Activate own to
prevent the SIM card being shut down due to inactivity.
www.gsm-activate.co.uk - 01273462380 - [email protected]
Below is a notepad to help you remember the numbers that you have saved to your unit in
the event you need to modify or delete in the future.
#1=_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #
#2= _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #
#3=_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #
How to programme the SMS text message
You can now change the alarm message from “input detected” to one of your own choice.
To change the message send the text command as follows
#MESS=YOUR MESSAGE#
The detector will reply with a text message - “MESSAGE STORED”
IMPORTANT - PLEASE READ
You can only use a maximum of 19 characters including spaces for your customised
message.
Page 4
How to Programme Mobile Numbers
After inserting the simcard into the GSM module, turn the unit on and wait until you see the
GREEN LED is on. This indicates that the module has a signal and the unit is ready for use.
Please Note - To avoid confusion we have colour coded the hash (#) and the equals (=)
symbols. Furthermore, where it indicates a phone number this should be
your number or the numbers you wish the unit to contact.
Example: (hash) (1,2 or 3) (equals) (phone number) (hash)
To programme mobile numbers into the unit you will need to send them as a text to the unit
as follows:
#1=07123456789# Then send this as a text to the unit for contact no: 1
#2=07234567891# Then send this as a text to the unit for contact no: 2
#3=07345678912# Then send this as a text to the unit for contact no: 3
If you wish to cancel a number, follow this example.
(HASH) (1,2 or 3) (EQUALS) (DELETE) (HASH)
#1=DELETE#
This will delete contact no: 1
IMPORTANT - PLEASE READ
Please only send one message at a time and wait for the GSM detector to send back the
text acknowledgement “NUMBER STORED” before you try to add the next number.
www.gsm-activate.co.uk - 01273462380 - [email protected]
Page 5
Telephone Call Alerts
The Door Contact Alarm can be programmed to send you a telephone call after each text
alarm has been sent.
You will receive approximately three ring tones. The unit will then hang up automatically.
This is to prevent call charges being incurred.
To text call alerts to ON please send the text message
#CALL=ON#
The unit will reply back with the message - “CALL ON”
To disarm call alerts please send the text message.
#CALL=OFF#
If the call function has been set to ON you will receive a text message and shortly after a
phone call.
How to use the 2G/3G Door Contact Alarm
Once you have positioned the door contact, installed the simcard and programmed the
numbers the system is ready to use.
The GSM Door Contact Alarm has two modes, alarm mode and auto mode.
Alarm mode: you have to arm the alarm manually each time when required via a text
message command or via the keyfob provided.
Auto mode: the alarm is always armed. You should choose which mode is more suitable
to your application.
These modes are selected by sending the following text messages
#Mode=1# Auto Mode
#Mode=2# Alarm Mode (default)
The default setting is alarm mode, to get an alarm notification when the beam is triggered,
you will need to arm the alarm first via text message or key fob
www.gsm-activate.co.uk - 01273462380 - [email protected]
Arm Via Text Message
To set the alarm to ON you will need to send the text message
#ALARM=ON# This will activate the alarm
#ALARM=OFF# This will deactivate the alarm
It is important to remember that once the alarm has been triggered you will need to reset
the alarm by sending the text command #ALARM=ON# to reactivate the alarm or activate
it using the key fob.
Arm Via Key Fob
The key fob works best when used with the siren provided as you will get the audible alert
whenever you arm or disarm the alarm.
Press button A on the key fob Arms the alarm and siren will beep twice
Press button B on the key fob Disarms the alarm and the siren will beep twice
IMPORTANT - PLEASE READ
Again it is important to remember that when the alarm has been triggered you will need to
reset the alarm using either the text command (above) or by using the fey fob.
In auto mode, the key fob and text message are disabled, the alarm is always “Active”.
After the alarm is triggered it will automatically reset to active after 20 seconds
In the event of a power loss the unit will remember if it was armed when power is restored.
How to use the Relay Output
The relay has been programmed to trigger the siren for 60 seconds in the event of an
alarm activation. Once the text message and call has been received you can stop the siren
sounding by pressing B on the key fob.
If you do not require the siren to sound in the event of an alarm activation but require it so
that you hear the key fob activation you can turn the siren OFF by Dipswitch 1.
Dipswitch 1 ON Siren is turned ON
Dipswitch 1 OFF Siren turned OFF
If you require the ability for the relay to be independently activated like older versions of
this alarm, please contact us on the details below.
www.gsm-activate.co.uk - 01273462380 - [email protected]
Page 6
Page 7
To connect wireless door sensors you will need to match the deveices to the receiver
on the dialler.
1. Hold down the pairing button on the RF Module for 3 seconds
(refer to figure 1)
2. Trigger the door switch
3. The RF module has a RED LED which will flash when pairing in complete.
Figure 1
Pairing the Wireless Door Sensors
www.gsm-activate.co.uk - 01273462380 - [email protected]
Quick Reference
Factory Reset
To set the unit back to factory settings you will need to send a text message
#RESET#
Please Note - doing this will reset ALL of your parameters. Only send a reset command
when necessary.
The GREEN ready LED will flash eight times.
Dipswitch Settings
Dipswitch 1 = ON = Siren ON
OFF = Siren OFF
Dipswitch 2 = ON = 3G
OFF = 2G
For more technical support please browse the FAQ’s on our website www.gsm-
activate.co.uk
Alternatively email our technical support team at [email protected] and we will
do our best to respond to your querry within 24 hours Monday- Friday.
06/10/21 - GD Page 8
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere GSM Activate Sicherheitssystem Handbücher
GSM Activate
GSM Activate AD-SD Bedienungsanleitung
GSM Activate
GSM Activate GSM PT100 Bedienungsanleitung
GSM Activate
GSM Activate 2G RF BEAM Bedienungsanleitung
GSM Activate
GSM Activate Alarm Pro 20 Bedienungsanleitung
GSM Activate
GSM Activate ECO-BEAM Bedienungsanleitung
GSM Activate
GSM Activate 2G RF PIR Bedienungsanleitung
GSM Activate
GSM Activate ECO Series Bedienungsanleitung
GSM Activate
GSM Activate ADRV11 Bedienungsanleitung
GSM Activate
GSM Activate 3G RF DOOR Bedienungsanleitung
GSM Activate
GSM Activate GSM 4G AUTO DIALLER PLUS Bedienungsanleitung
Beliebte Sicherheitssystem Handbücher anderer Marken
EDM
EDM Solution 6+6 Wireless-AE Bedienungsanleitung
Highway Safety Group
Highway Safety Group EA401 Bedienungsanleitung
Siren
Siren LED GSM Bedienungsanleitung
Detection Systems
Detection Systems 7090i Montageanleitung
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung
Siemens
Siemens FDM273 Bedienungsanleitung