Guilin Feiyu Technology A2000 Bedienungsanleitung
User M a n u a l
EN V 1.0
3-Axis Gimbal for Mirrorless Camera
GuiLin FeiYu Technology Incorporated Company
2
(1) Align the adjustment skateboard to the 1/4 screw
hole at the bottom of the camera and place to the
appropriate position，then tighten the screw.
1
1. Installation
Attention: Please complete the following instructions before power on the gimbal
!
As the stabilizer comes with boot self-test function, such as the stabilizer due to no load, the balance
adjustment is less than ideal, or due to the intensity adjustment does not fit and other reasons cause
the stabilizer vibration is too large, the gimbalwill automatically enter the standby mode.
Attention
Insert the batteries
Remove the handle, insert
2 pcs 18650 batteries and
tighten the screw.
Prior to use, please be sure to fill the battery.
Installation of the camera
18650
18650
1
After installing the camera, first press and hold the
anti-column, place the adjustment skateboard with
the camera mounted on the clamping plate,and
tighten the fixing screws.
In case of low battery, the indicator will light red
and flash 3 times every 5 seconds. Please charge
gimbal or replace the battery.
Power on / off
Power on：Long press Function button
and release it until the green
light is on.
Power off：
Long press Function botton
and release it until the green
light changes from quick
flashing to constant.
（2）3
!
Anti-
column Thumb
screw
2
[19] Tilting lock screw
[20] Charging indicator
[21] Shutter cable socket
[22] Sliding arm
[23] Trigger button
[24] Sliding arm
[25] Function shortcuts
[18] Cross arm
[2] Rolling axis
[3] Rolling lock screw
[4] Vertical arm
[13] Handle
[11] Socket connector
[7] Function button
[5] Indicator
[6] Joystick
[12] USB interface
[17] Thumb screw
[14] Up adjustment skateboard
[15] Down adjustment skateboard
[16] Adapter(Clamping plate)
[10] Panning axis
[9] Heading lock screw
[1] Tilting axis
2. Product Overview
[8] Shutter button
[1]
[2]
[3]
[18]
[19]
[24]
[16] [15]
[14] [17]
[23]
[12]
[20]
[9]
[10]
[11]
[8] [7]
[6] [5]
[13]
[4]
[22]
[21]
[25]
3
Basic accessories
After installation, please
tighten the retaining ring
!
Single-armed
installation
Dual Handheld
Installation
USB cable
（micro port） Batteries
(Type: 18650)
SONY shutter line
(3.5 audio to multi)
Smart charger Thumb screw Camera support
frame screws
Camera support
frame Code shoe
α2000 Double-hand foldable set
Retaining ring
1/4 screw
（Double-hand foldable set）
α2000 Single Handle
Advanced accessories
Installation way
4
Trigger button
Lock
3. Modes / Functions
Function button
Double tap
Double tap
Single tap
Function
Triple tap
Reset
Long press
Panning Mode
Panning and Tilting Mode
Lock Mode
Reset
* Boot default mode: Panning mode
The orientation of the camera is fixed.
Reset the tilting axis of the gimbal to initial orientation and initial mode
Reset the tilting axis of the gimbal to initial
orientation and initialmode
Explanation
Function Explanation
Panning mode
Panning and Tilting mode Under panning and tilting mode, single tap to switch to panning mode
Rotate 180°in horizontal Make the camera lens rotate 180 ° (The rotation angle is restored by the
reset function)
Single tap to switch to panning mode
Tilting and rolling direction are fixed, and the camera lens moves according to the hand movement of the user.
Operating Instructions of Button
Working Modes
Other Functions
The rolling direction is fixed, and the camera lens moves according to the hand movement of the user.
Charge
USB charge Input：5V/1A
1
2
In the panning mode or panning and pitch mode, press and hold lock
shortcuts to enter the lock mode, release to return before mode.
Quadruple tap Quadruple tap to enter autototation mode
Autorotation Mode
Fifth tap Single tap again to awake the gimbal, or triple tap to initialize the gimbal
Initialization
5
3Autorotation Mode
Four times clicks on function button, gimbal will access the autorotation mode setting. Manually turn the gimbal to an initial position,
then click again on function button for recording it. Manually turn the gimbal to end position, then click the function button again for
recording it. Gimbal will turn to the initial position and begin autorotation.
1.Four times clicks on function
button, gimbal will access the
autorotation mode setting.
Tilting
Tilting
Panning
Panning
2. Turn the panning axis and tilting
axis to the position ① and hold for
half a second.Click on function
button, record the position ①.
3 .Turn the panning axis and tilting
axis to the position ②
and hold for
half a second.
Lick on the function
button again,record the position ②.
①
②
②
①
6
4.Gimbal will recover to
position ① automatically.
Tilting axis and panning
axis turn to position ②
at constant speed.The
gimbal is automatically
reset after the end.
gimbal speed setting reference table
Annexed parameter table：
gimbal autorotation function with micrrorless camera delay
photography function can be used to achieve a very special
mobile delay photography. The speed setting is made by
Feiyu ON App.
8 hours / turn
4 hours / turn
1 hours / turn (default)
30 minutes / turn
15 minutes / turn
2 minutes / turn
4 minutes / turn
8 minutes / turn
30 seconds / turn
24 seconds / turn
18 seconds / turn
12 seconds / turn
1 minutes / turn
α2000 Rotate Speed
4. Manual Lock
Hold the camera and
change its angle in
tilting axis direction.
Keep this position for
half second, the
current angle will be
locked manually.
2
1
7
Manual lock ，pull to the specified angle to stay half a
second can be lock the current angle.(The tilting axis and
panning axis in the lock mode can be manual lock and the
tilting axis can be manual lock in the panning mode.)Take
the tilting axis as an example:
Explanation of LED indicator status
5. Operation
Explanation of joystick control
Other functions
Switch the working mode
Power on / off
Identify the current mode of the
gimbal by the indicator
Function Button
Shutter button
Click the shutter button to focus, click again
within 3s to take pictures.
If there is no operation within 3s, the focus
state is cleared(need connect a camera control cable )
Up
Down
Left
Right
LED status Mode / Status
Blue light flashes once
Blue light flashes twice
Panning mode
Panning and Tilting mode
Lock mode / Initialize the gimbalBlue light constant on
Blue light keeps flashing Initialization failure / Malfunction
Low battery Red light flashes three times
Red light keeps flashing Entering standby /
Entering power off
Explanation of Charging indicator status
LED status Mode / Status
Blue light，
red light off
The blue and red light
are flashing
Stop charging
The voltage of two batteries
balance ajustment
The blue and red light Charging
状态指示灯Indicator
Charging indicator
（If the two batteries voltage difference between the
larger, the process takes a long time）
8
6. Balance Adjustment
STEP 1
Balance adjustment of the tilting axis
（1） Adjust the camera's pitch axis Vertical center of gravity: place the camera lens down vertically, keep the
arm horizontal and observe the camera lens status. Adjust the arm up and down to adjust the balance.
(See below)
Normal vertical
* After adjustment, be sure to tighten the lock screw.
Camera forward Camera backward
L
T
L
T
Slide the arm up to adjust Slide the arm down to adjust
9
Andere Handbücher für A2000
1
Inhaltsverzeichnis
Andere Guilin Feiyu Technology Kamerazubehör Handbücher
Guilin Feiyu Technology
Guilin Feiyu Technology G5 Handbuch
Guilin Feiyu Technology
Guilin Feiyu Technology SPG 2 Bedienungsanleitung
Guilin Feiyu Technology
Guilin Feiyu Technology A2000 Kurzanleitung
Guilin Feiyu Technology
Guilin Feiyu Technology G6 Plus Bedienungsanleitung
Guilin Feiyu Technology
Guilin Feiyu Technology FY WG2 3 Axis Bedienungsanleitung
Guilin Feiyu Technology
Guilin Feiyu Technology G5 Bedienungsanleitung
Guilin Feiyu Technology
Guilin Feiyu Technology Vimble 2 Bedienungsanleitung
Guilin Feiyu Technology
Guilin Feiyu Technology G5 GS Bedienungsanleitung
Guilin Feiyu Technology
Guilin Feiyu Technology VIMBLE C Bedienungsanleitung
Guilin Feiyu Technology
Guilin Feiyu Technology SPG Plus Bedienungsanleitung
