Gunnebo RotaSec B120S Bedienungsanleitung

.............................

CCEC/ OM Manuals RotaSec Titan 1.5 08.2009

This Manual Refers to the RotaSec fitted with the Titan Head

RotaSec –With Damping

Installation Operation and Maintenance Manual

.............................

CCEC/ OM Manuals RotaSec Titan 1.5 08.2009

.............................

CCEC/ OM Manual RotaSec Titan 1.5 EN 08.2009

Contents

Page

SECTION 1INTRODUCTION ...................................................................................................................................... 5

General .............................................................................................................. 5

Electrical Warnings ............................................................................................ 5

Errors.................................................................................................................. 5

Proprietary Notices ............................................................................................ 5

Hardware Changes............................................................................................. 5

Rotating Machinery ........................................................................................... 6

Warnings, Cautions and Notes .......................................................................... 6

Good Practices ................................................................................................... 6

Equipment Safety Systems ................................................................................. 6

Risk Assessment ................................................................................................. 7

CE - Marking....................................................................................................... 8

SECTION 2PRODUCT DESCRIPTION ........................................................................................................................... 9

Product Description............................................................................................ 9

Typical Units..................................................................................................... 11

Technical Details .............................................................................................. 13

Standard Technical Specification ..................................................................... 13

SECTION 3INSTRUCTIONS FOR USE ......................................................................................................................... 15

Operating Sequence......................................................................................... 15

Access Control Devices..................................................................................... 16

Programmable Parameters.............................................................................. 16

SECTION 4TECHNICAL INFORMATION ...................................................................................................................... 17

Standard Features............................................................................................ 17

Optional Features ............................................................................................ 17

Typical Layout Details ...................................................................................... 18

Typical Titan Head Mechanism Elevation ........................................................ 23

Drives and Controls.......................................................................................... 23

Restoring Force Adjustment............................................................................. 24

Damping Adjustment....................................................................................... 25

Electrical Connections ...................................................................................... 25

Sensor Timing and Solenoid Operation ............................................................ 26

Anti-reverse Ratchet Quietening Adjustment .................................................. 26

Locking Solenoid Adjustment........................................................................... 27

Electronic Circuit Boards .................................................................................. 28

LCM02 Control Logic Board.............................................................................. 29

Start-up Functions............................................................................................ 29

Changes to the Programmable Parameters..................................................... 30

Basic Configuration.......................................................................................... 32

Parameter Default Setting ............................................................................... 32

Voltage Free Outputs ....................................................................................... 33

Sensor Board .................................................................................................... 33

LEDs.................................................................................................................. 33

SNT1 Card ........................................................................................................ 34

Power Supply Unit............................................................................................ 35

Solenoid Loom Connections ............................................................................. 36

.............................

CCEC/ OM Manual RotaSec Titan 1.5 EN 08.2009

SECTION 5INSTALLATION...................................................................................................................................... 37

Unpacking ........................................................................................................ 37

Tools Required ................................................................................................. 37

Site Preparation ............................................................................................... 37

Headroom ........................................................................................................ 57

Conduit Routing ............................................................................................... 57

Cable Requirements ......................................................................................... 57

Cable Controls .................................................................................................. 57

General Details................................................................................................. 58

Basic Principles of Setting To Work (Fig 5.21 and 5.22) ................................. 58

Variations for “R” Models ................................................................................ 59

Variations for “S” Models ................................................................................ 59

Electrical Connections ...................................................................................... 78

Testing after Installation.................................................................................. 79

SECTION 6MAINTENANCE..................................................................................................................................... 86

General Care .................................................................................................... 86

Routine Maintenance....................................................................................... 87

Fault Finding .................................................................................................... 89

SECTION 7SPARE PARTS ....................................................................................................................................... 91

Recommended Spare Parts.............................................................................. 91

SECTION 8TABLE APPENDICES ............................................................................................................................... 92

Firmware Version - FBCBQMYR110 ................................................................. 93

Firmware Version (FBCBQMYR123) ................................................................. 95

SECTION 9DECLARATION OF CONFORMITY............................................................................................................... 97

.............................

CCEC/ OM Manual RotaSec Titan 1.5 EN 08.2009

Section 1 Introduction

Introduction

General

Please read this manual carefully, it contains information that will assist you with all aspects of

installation and maintenance, including unpacking. Correct installation & Maintenance will ensure

smooth functionality and increase the lifespan of components.

Gunnebo Entrance Control Ltd makes every effort to ensure that this manual is reviewed whenever

significant changes are made to the design. However, our policy of continuous improvement may

result in some small differences between the unit supplied and the description in this document.

Enquiries in this respect should, in the first instance, be directed to our Technical Department. .

Telephone +44 (0) 1825 746105, Fax +44 (0) 1825 763835,

E-mail turnsupport.entrancecontrol@gunnebo.com

Electrical Warnings

The electrical power used in this equipment is at a voltage high enough to endanger life. Before

carrying out maintenance or repair, you must ensure that the equipment is isolated from the electrical

supply and sufficient tests made to verify that the isolation is complete.

When the supply cannot be disconnected, functional testing, maintenance and repair of the electrical

units are to be undertaken only by persons fully aware of the danger involved and who have taken

adequate precautions and training.

Errors

Reports on errors, comments and suggestions concerning this manual are requested and encouraged.

They should be submitted to:

Gunnebo Entrance Control Ltd, Bellbrook Business Park, Uckfield, East Sussex, TN22 1QQ, UK.

Telephone +44 (0) 1825 761022, Fax +44 (0) 1825 763835,

E-mail turnsupport.entrancecontrol@gunnebo.com

Proprietary Notices

All data appearing herein is of a proprietary nature, with exclusive title to it held by Gunnebo. The

possession of this Manual and the use of the information are therefore restricted only to those persons

duly authorised by Gunnebo.

Do not reproduce, transcribe, store in a retrieval system or translate into any human or computer

language, any part of this Manual without prior permission of Gunnebo.

Hardware Changes

No hardware changes may be made without authority from Gunnebo who will be responsible for

ensuring that the proposed change is acceptable in all safety aspects. Personnel authorised by

Gunnebo may only make hardware changes.

Any maintenance or modification of Emergency Stop and Guarding Circuitry must be followed by

safety checks on the whole hardwired Emergency Stop and Guarding Circuitry.

Prior to a hardware change, records must be made of the change, one of which MUST be sent to the

Technical Department at Gunnebo.

.............................

CCEC/ OM Manual RotaSec Titan 1.5 EN 08.2009

Rotating Machinery

Rotating industrial machinery may possess huge amounts of stored energy. On no account must you

commence maintenance if you do not fully understand what you are doing and/or have not taken all

the safety precautions normally associated with industrial electronic control systems and machines.

Before starting to work on the equipment, please make yourself familiar with all the associated blocks

in the system, including control loops, mechanics, drives, transducers and electrics. Please read all

the Manuals of the equipment you are unfamiliar with first.

Warnings, Cautions and Notes

Where necessary within the technical manual, Warnings, Cautions and Notes may be given.

Warnings

Are for conditions that might endanger people; the instructions given in Warnings must be followed

precisely. They are given to avoid injury or death.

Cautions

Are for conditions that may cause damage to equipment or may spoil work; The instructions given in

Cautions must be followed to avoid spoilt work or damage to equipment.

Notes

Alert the user to pertinent facts and conditions.

Static Sensitive Devices

Some of the PCBs within in the equipment, which is covered by this technical manual, contain Static

Sensitive Devices. It is recommended that maintenance and service engineers are fully aware of the

Local Industry Regulations and procedures when handling such devices.

Good Practices

Equipment being installed must not be left unattended unless all potential mechanical and electrical

hazards have been made safe. A competent person must be left in charge when the equipment is to

be left whilst potentially unsafe.

The following points indicate good practice that will contribute to safety and avoid equipment damage.

i Ensure that all electrical power supplies and batteries are turned OFF and disconnected

before working on any of the equipment.

ii Never leave the equipment in a potentially dangerous state.

iii Use only the correct tools for the task in hand.

iv When working on the equipment, remove any personal jewellery that may be

conductive, or clothing that may become entangled with mechanical parts.

Equipment Safety Systems

Safety systems and controls, such as interlocks, covers and guards, must not be overridden or

bypassed by personnel, other than authorised staff who are qualified to carry out prescribed actions

within specified Warnings.

.............................

CCEC/ OM Manual RotaSec Titan 1.5 EN 08.2009

Risk Assessment

Risk assessment is graded into categories of safety, rated 1 to 8 (where 8 is the highest risk level).

The following activities are covered.

Rating Activity

1 Cleaning

2 General Installation

3 Roof Installation

Servicing

4 Servicing

General Maintenance

Using Chemical Fixers

5 Commissioning

8 Floor Drilling

Rating 1: Cleaning.

Who is at Risk Engineers or Site personnel

Hazard Misuse of Cleaning Fluids

Current Controls Compliance with COSHH regulations

Rating 2: General Installation

Who is at Risk Site personnel

Hazard Objects/Tools in Installation area

Current Controls Trained Installation Engineers

Rating 4: General Maintenance

Who is at Risk Site Personnel

Hazard Electric Shock

Current Controls Isolation of Power/Trained Service Personnel

Using Chemical Fixer

Who is at Risk Site Personnel within the Vicinity of the Work Area

Hazard Fume Inhalation

Current Controls Compliance with COSSH regulations

Rating 5: Commissioning

Who is at Risk Site Engineer

Hazard Power Supply/Moving Parts

Current Controls Isolate Power

Rating 8: Floor Drilling

Who is at Risk Installation Engineer

Hazard Flying Debris and Noise

Current Controls Protective Equipment must be worn

.............................

CCEC/ OM Manual RotaSec Titan 1.5 EN 08.2009

CE - Marking

The Gunnebo RotaSec is CE marked, developed and manufactured according to the EU‟s Machinery,

Low-Voltage and EMC-Directives.

With each unit a Declaration of Conformity is supplied.

Important Notice

The Gunnebo RotaSec is a security product and as such, any Children or Minors using the turnstile,

MUST be supervised and accompanied by a responsible Adult.

Gunnebo does not accept any liability if this Important Safety Notice is not

enforced.

.............................

CCEC/ OM Manual RotaSec Titan 1.5 EN 08.2009

Section 2 Product Description

Product Description

The RotaSec is designed for use in external entrances to Administrative Centres, Industrial

Complexes and Military Establishments where high quality, combined with high security full height

barriers are required.

An all welded steel rotor with straight arms runs in a phosphor bronze bearing at the top end and

supported by a ball and cone bearing at the base.

On double units the rotors can be interlocked where space is of prime importance.

Entry and Exit can be made by Card reader, Pushbutton or any other type of control device specified

by the client at the time of order.

All controls are housed within the unit, therefore NO separate switches or control boxes are required.

Control of the rotor is achieved usually by an electro-mechanism mounted within the top section of the

RotaSec and accessible via service panels. Purely mechanical control is also possible.

Power for the unit is 24V DC derived from a mains input transformer and rectifier circuit.

.............................

CCEC/ OM Manual RotaSec Titan 1.5 EN 08.2009

The following variations can be supplied by Gunnebo; however this Technical Manual provides

sufficient information to cover all models.

MODEL UNIT-TYPE

B90S (Basic) Single Unit, open frame design without canopy

B120S (Basic) Single Unit, open frame design without canopy

F90S Single Unit without canopy

F120S Single Unit without canopy

R90S Single Unit with canopy

R120S Single Unit with canopy

S90S Single Unit with canopy and side panels

S120S Single Unit with canopy and side panels

B90D (Basic) Double Unit, open frame design without canopy

B120D (Basic) Double Unit, open frame design without canopy

F90D Double Unit without canopy

F120D Double Unit without canopy

R90D Double Unit with canopy

R120D Double Unit with canopy

S90S Double Unit with canopy and side panels

S120D Double Unit with canopy and side panels

F90DI Interlocked Double Unit without canopy

F120DI Interlocked Double Unit without canopy

R90DI Interlocked Double Unit with canopy

R120DI Interlocked Double Unit with canopy

S90DDI Interlocked Double Unit with canopy and side panels

S120DDI Interlocked Double Unit with canopy and side panels

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Gunnebo Drehkreuz Handbücher

Gunnebo

Gunnebo DL645 Bedienungsanleitung

Beliebte Drehkreuz Handbücher anderer Marken

Oxgard

Oxgard CUBE C-10 Bedienungsanleitung

LBA GROUP

LBA GROUP LBAT10 Bedienungsanleitung

Magnetic

Magnetic mTripod Bedienungsanleitung

Kaba

Kaba Argus HSG-E02 Bedienungsanleitung

Automatic Systems

Automatic Systems TR491 Bedienungsanleitung

Turnstiles

Turnstiles HZ-SWGS01 Bedienungsanleitung

DSI

DSI DST-80 Bedienungsanleitung

OZAK

OZAK VP-125 Handbuch

Automatic Systems

Automatic Systems SMARTLANE SL 90X Bedienungsanleitung

Alvarado

Alvarado MT Montage- und Bedienungsanleitung

JKDC SECURITY

JKDC SECURITY JKDC-100C Bedienungsanleitung

Alvarado

Alvarado SU5000 Bedienungsanleitung

Magnetic Autocontrol

Magnetic Autocontrol MPT 33 Bedienungsanleitung

Oxgard

Oxgard Praktika T-04K Kurzanleitung

digicon

digicon CATRAX Plus Bedienungsanleitung

Oxgard

Oxgard CUBE C-04-s Bedienungsanleitung

BOON EDAM

BOON EDAM Turnlock 100 Leitfaden

Wano

Wano Tripod BO-DSN10 Bedienungsanleitung