GW Instek MSO-2000EA Bedienungsanleitung

Mixed-Signal Oscilloscope

MSO-2000E & MSO-2000EA

USER MANUAL

ISO-9001 CERTIFIED MANUFACTURER

April 2019

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

rights to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan

TABLE OF CONTENTS

Table of Contents

SAFETY INSTRUCTIONS .................................................. 6

GETTING STARTED........................................................ 11

MSO-2000E/2000EA Series Overview ......................... 12

Appearance ................................................................ 16

Set Up ....................................................................... 29

Built-in Help .............................................................. 39

MEASUREMENT ............................................................ 40

Basic Measurement ................................................... 41

Automatic Measurement............................................ 48

Cursor Measurement ................................................. 63

Math Operation ......................................................... 71

ADVANCED CONFIGURATION ....................................... 81

Acquisition ................................................................ 84

Segmented Memory Acquisition ................................ 89

Display .....................................................................101

Horizontal View ........................................................106

Vertical View (Channel).............................................114

Bus Key Configuration ..............................................122

Trigger ......................................................................148

Search.......................................................................190

System Settings and Miscellaneous Settings ............199

LOGIC ANALYZER .........................................................204

Logic Analyzer Operation..........................................205

ARBITRARY WAVE GENERATOR ....................................220

Arbitrary Wave Generator Operation .........................221

MSO-2000E & 2000EA User Manual

APPLICATIONS .............................................................255

Introduction............................................................. 256

Go-NoGo application ............................................... 258

DVM application ...................................................... 263

Data Log application ................................................ 265

Digital Filter application .......................................... 267

Mask application ..................................................... 269

SAVE/RECALL ...............................................................279

File Format/Utility ................................................... 280

Create/Edit Labels ................................................... 286

Save ......................................................................... 289

Recall ....................................................................... 297

Reference Waveforms ............................................... 303

FILE UTILITIES .............................................................305

File Navigation ........................................................ 306

Create Folder ........................................................... 308

Rename File ............................................................. 309

Delete File or Folder ................................................ 310

Copy File to USB ...................................................... 311

HARDCOPY KEY ...........................................................312

REMOTE CONTROL CONFIG ........................................316

Interface Configuration ............................................ 317

MAINTENANCE ............................................................327

FAQ..............................................................................333

APPENDIX ....................................................................336

Updating the Firmware ............................................ 337

MSO-2000E/2000EA Specifications .......................... 339

Probe Specifications ................................................ 344

TABLE OF CONTENTS

Dimensions ..............................................................346

Declaration of Conformity .........................................347

INDEX ..........................................................................348

MSO-2000E & 2000EA User Manual

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow during

operation and storage. Read the following before

any operation to insure your safety and to keep

the instrument in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the Product

name.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the equipment or to

other properties.

DANGER High Voltage

(Note)

Attention required

Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

SAFETY INSTRUCTIONS

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased.

Safety Guidelines

General

Guideline

WARNING

CAUTION

Make sure the BNC input voltage does not

exceed 300Vrms.

Never connect a hazardous live voltage to the

ground side of the BNC connectors. It might

lead to fire and electric shock.

Do not place any heavy object on the MSO-

2000E/2000EA.

Avoid severe impact or rough handling that

leads to damaging the MSO-2000E/2000EA.

Do not discharge static electricity to the MSO-

2000E/2000EA.

Use only mating connectors, not bare wires, for

the terminals.

Do not block the cooling fan opening.

Do not perform measurement at a power source

or building installation (Note below).

Do not disassemble the MSO-2000E/2000EA

unless you are qualified.

Note

(Measurement categories) EN 61010-1:2010 specifies the

measurement categories and their requirements as follows. The

MSO-2000E/2000EA falls under category I.

Measurement category IV is for measurements performed at the

source of low-voltage installation.

Measurement category III is for measurements performed in the

building installation.

Measurement category II is for measurements performed on

circuits directly connected to the low voltage installation.

Measurement category I is for measurement performed on

circuits not directly connected to Mains.

MSO-2000E & 2000EA User Manual

Power Supply

WARNING

AC Input voltage: 100 - 240V AC, 50 - 60Hz,

auto selection. Power consumption: 30 Watts.

Connect the protective grounding conductor of

the AC power cord to an earth ground, to avoid

electrical shock.

Cleaning the

MSO-2000E

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid.

Do not use chemicals containing harsh materials

such as benzene, toluene, xylene and acetone.

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Relative Humidity: ≤80%, 40°C or below; ≤45%,

41°C ~ 50°C

Altitude: < 2000m

Temperature: 0°C to 50°C

Note

(Pollution Degree) EN 61010-1:2010 specifies the pollution degrees

and their requirements as follows. The MSO-2000E/2000EA falls

under degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of dielectric

strength or surface resistivity”.

Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

Pollution degree 2: Normally only non-conductive pollution

occurs. Occasionally, however, a temporary conductivity caused

by condensation must be expected.

Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment

is normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature

nor humidity is controlled.

SAFETY INSTRUCTIONS

Storage

environment

Location: Indoor

Temperature: -10°C to 60°C

Humidity: Up to 93% RH (non-condensing) /

≤40ºC, up to 65% RH (non-condensing) / 41ºC

~ 60 ºC

Disposal

Do not dispose this instrument as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased. Please make sure

discarded electrical waste is properly recycled to

reduce environmental impact.

MSO-2000E & 2000EA User Manual

Power cord for the United Kingdom

When using the oscilloscope in the United Kingdom, make sure the

power cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

As the colours of the wires in main leads may not correspond with

the coloured marking identified in your plug/appliance, proceed

as follows:

The wire which is coloured Green & Yellow must be connected to

the Earth terminal marked with either the letter E, the earth symbol

or coloured Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the

terminal marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment

or contact the supplier.

This cable/appliance should be protected by a suitably rated and

approved HBC mains fuse: refer to the rating information on the

equipment and/or user instructions for details. As a guide, a cable

of 0.75mm2should be protected by a 3A or 5A fuse. Larger

conductors would normally require 13A types, depending on the

connection method used.

Any exposed wiring from a cable, plug or connection that is

engaged in a live socket is extremely hazardous. If a cable or plug is

deemed hazardous, turn off the mains power and remove the cable,

any fuses and fuse assemblies. All hazardous wiring must be

immediately destroyed and replaced in accordance to the above

standard.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GW Instek Prüfgeräte Handbücher

GW Instek

GW Instek GOS-620FG Bedienungsanleitung

GW Instek

GW Instek GRS-6052A Bedienungsanleitung

GW Instek

GW Instek PEL-3000 Series Bedienungsanleitung

GW Instek

GW Instek GLC-10000 Bedienungsanleitung

GW Instek

GW Instek GDS-2000A Series Bedienungsanleitung

GW Instek

GW Instek GDS-1000A-U Series Bedienungsanleitung

GW Instek

GW Instek GDS-3000 Series Bedienungsanleitung

GW Instek

GW Instek GDS-1000B Series Betriebsanleitung

GW Instek

GW Instek LCR-16 Bedienungsanleitung

GW Instek

GW Instek GUT-6000A Bedienungsanleitung

GW Instek

GW Instek MSO-2000E Bedienungsanleitung

GW Instek

GW Instek GDS-2072A Bedienungsanleitung

GW Instek

GW Instek AEL-5000 Series Bedienungsanleitung

GW Instek

GW Instek LCR-05A Bedienungsanleitung

GW Instek

GW Instek GPT-700A Series Bedienungsanleitung

GW Instek

GW Instek GDS-1000-U Series Bedienungsanleitung

GW Instek

GW Instek PEL-3000AH Series Bedienungsanleitung

GW Instek

GW Instek GPT-9801 Bedienungsanleitung

GW Instek

GW Instek GPT-9000 series Bedienungsanleitung

GW Instek

GW Instek GDS-3000 Series Bedienungsanleitung

GW Instek

GW Instek GDS-800 Series Bedienungsanleitung

GW Instek

GW Instek GCP-300 Bedienungsanleitung

GW Instek

GW Instek C-1200 Bedienungsanleitung

GW Instek

GW Instek GOS-6103C Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung