H3C S3610 Series Montageanleitung
H3C S3610&S5510 Series Ethernet Switches
Command Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: T2-08192P-20070416-C-1.02
Product Version: Release 0001
Copyright © 2006-2007, Hangzhou H3C Technologies Co., Ltd. and its licensors
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any means
without prior written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H3Care,
, TOP G, , IRF, NetPilot,
Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,
Storware, NQA, VVG, V2G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and
HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their
respective owners.
Notice
The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the contents, but
all statements, information, and recommendations in this document do not constitute
the warranty of any kind, express or implied.
To obtain the latest information, please access:
http://www. h3c.com
Technical Support
customer_service@h3c.com
http://www. h3c.com
About This Manual
Related Documentation
In addition to this manual, each H3C S3610&S5510 Series Ethernet Switches
documentation set includes the following:
Manual Description
H3C S3610&S5510 Series Ethernet
Switches Operation Manual-Release
0001
It is used for assisting the users in data
configurations and typical applications.
(See the electronic documentation for
details)
H3C S3610 Series Ethernet Switches
Installation Manual
It provides information for the system
installation. (See the electronic
documentation for details)
H3C S5510 Series Ethernet Switches
Installation Manual
It provides information for the system
installation. (See the electronic
documentation for details)
Organization
H3C S3610&S5510 Series Ethernet Switches Command Manual Release 0001 is
organized as follows:
Part Contents
1 Login Introduces the commands used for
logging into the Ethernet switch.
2 VLAN Introduces the commands used for
configuring VLAN, Voice VLAN, and
GVRP.
3 IP Address and Performance Introduces the commands used for
configuring IP address and IP
performance
4 QinQ-BPDU Tunnel Introduces the commands used for
configuring QinQ and BPDU TUNNEL.
5 Port Correlation Configuration Introduces the commands used for
configuring link aggregation and port
isolation.
6 MAC Address Table Management Introduces the commands used for
configuring MAC address forwarding
table.
Part Contents
7 MAC-IP-Port Binding Introduces the commands used for
configuring MAC address, IP address
and port binding.
8 MSTP Introduces the commands used for
configuring STP and BRDU tunnel.
9 Routing Overview Introduces the commands used for
display and debugging IPv4/IPv6 routing
protocols.
10 IPv4 Routing
Introduces the commands used for
configuring IPv4 routing, static routing,
RIP, OSPF, IS-IS, BGP, and route
policy.
11 IPv6 Routing Introduces the commands used for
configuring IPv6 routing, static routing,
RIPng, OSPFv3, IS-ISv6, and BGP4+.
12 IPv6 Configuration Introduces the commands used for
configuring IPv6 application, IPv6
tunneling, and so on.
13 Multicast Protocol
Introduces the commands used for
configuring IGMP Snooping, MLD
Snooping, multicast VLAN, multicast
policy, IGMP, PIM-DM, PIM-SM, and
MSDP.
14 802.1x-HABP-MAC Authentication Introduces the commands used for
802.1x, HABP and MAC address
authentication related configurations.
15 AAA-RADIUS-HWTACACS Introduces the commands used for AAA,
RADIUS, HWTACACS, and the related
configurations.
16 ARP Introduces the commands used for ARP
and the related configuration.
17 DHCP Introduces the commands used for
DHCP and the related configuration.
18 ACL Introduces the commands used for
IPv4&IPv6-based ACL and the related
configuration.
19 QoS Introduces the commands used for QoS
and the related configuration.
20 Port Mirroring Introduces the commands used for port
mirroring and the related configuration.
21 Cluster Management Introduces the commands used for
cluster and the related configuration.
22 UDP Helper Introduces the commands used for UDP
Helper and the related configuration.
Part Contents
23 SNMP-RMON Introduces the commands used for the
configuration to manage network
devices through SNMP and RMON.
24 NTP Introduces the commands used for NTP
and the related configuration.
25 DNS Introduces the commands used for DNS
and the related configuration.
26 File System Management Introduces the commands used for file
system management.
27 Information Center Introduces the commands used for the
configuration to analyze and diagnose
networks using the information center.
28 System Maintenance and Debugging Introduces the commands used for daily
system maintenance and debugging.
29 NQA Introduces the commands used for NQA
and the related configuration.
30 VRRP Introduces the commands used for
VRRP and the related configuration.
31 SSH Introduces the commands used for SSH
and the related configurations.
32 Appendix Lists the acronyms used in this manual.
Conventions
The manual uses the following conventions:
I. Command conventions
Convention Description
Boldface The keywords of a command line are in Boldface.
italic Command arguments are in italic.
[ ] Items (keywords or arguments) in square brackets [ ] are
optional.
{ x | y | ... }
Alternative items are grouped in braces and separated by
vertical bars. One is selected.
[ x | y | ... ]
Optional alternative items are grouped in square brackets
and separated by vertical bars. One or none is selected.
{ x | y | ... } *
Alternative items are grouped in braces and separated by
vertical bars. A minimum of one or a maximum of all can be
selected.
Convention Description
[ x | y | ... ] *
Optional alternative items are grouped in square brackets
and separated by vertical bars. Many or none can be
selected.
# A line starting with the # sign is comments.
II. GUI conventions
Convention Description
< > Button names are inside angle brackets. For example, click
<OK>.
[ ] Window names, menu items, data table and field names
are inside square brackets. For example, pop up the [New
User] window.
/ Multi-level menus are separated by forward slashes. For
example, [File/Create/Folder].
III. Symbols
Convention Description
Warning Means reader be extremely careful. Improper operation
may cause bodily injury.
Caution Means reader be careful. Improper operation may cause
data loss or damage to equipment.
Note Means a complementary description.
Andere Handbücher für S3610 Series
21
Dieses Handbuch passt für folgende Modelle
1
Andere H3C Schalten Handbücher
H3C
H3C S5500-SI Series Montageanleitung
H3C
H3C S9500 Series Bedienungsanleitung
H3C
H3C PSR450-12A Bedienungsanleitung
H3C
H3C S9500 Series Montageanleitung
H3C
H3C S5500-SI Series Bedienungsanleitung
H3C
H3C S12500X-AF Series Kurzanleitung
H3C
H3C s5820x series Bedienungsanleitung
H3C
H3C S9500 Series Bedienungsanleitung
H3C
H3C S7500 Series Bedienungsanleitung
H3C
H3C Mini S9G Bedienungsanleitung
H3C
H3C S5500-SI Series Bedienungsanleitung
H3C
H3C S7500E-XS Series Installationshandbuch
H3C
H3C S6800-2C Bedienungs- und Wartungshandbuch
H3C
H3C CR19000-16 Bedienungs- und Wartungshandbuch
H3C
H3C S9500 Series Bedienungsanleitung
H3C
H3C S5500-EI series Bedienungsanleitung
H3C
H3C S3600-28PSI Bedienungsanleitung
H3C
H3C S9820-64H Bedienungs- und Wartungshandbuch
H3C
H3C S3100-52P Bedienungsanleitung
H3C
H3C S7500E-XS Series Bedienungsanleitung
