H3C S7500 Series Bedienungsanleitung
Operation Manual – Telnet Protection
H3C S7500 Series Ethernet Switches Table of Contents
i
Table of Contents
Chapter 1 Telnet Protection Configuration.................................................................................1-1
1.1 Introduction........................................................................................................................1-1
1.2 Telnet Protection Configuration.........................................................................................1-2
1.2.1 Configuring Telnet Protection..................................................................................1-2
1.2.2 Configuring SNMP Protection.................................................................................1-2
1.2.3 Configuring ICMP Protection...................................................................................1-2
1.2.4 Configuring Default-route Telnet Protection............................................................ 1-3
Operation Manual – Telnet Protection
H3C S7500 Series Ethernet Switches Chapter 1 Telnet Protection Configuration
1-1
Chapter 1 Telnet Protection Configuration
When configuring Telnet protection, go to these sections for information you are
interested in:
zIntroduction
zTelnet Protection Configuration
1.1 Introduction
The Telnet protection function is used to protect Telnet packets, SNMP packets, and
ICMP packets from the specific source IP addresses in the case of attacks against the
network or high CPU utilization.
Telnet protection comes in global Telnet protection, special ARP Telnet protection, and
default-route Telnet protection. Global Telnet protection is the highest in priority; then
comes special ARPTelnet protection and default-route Telnet protection is the lowest in
priority.
After you configure global Telnet protection, all the Layer-3 interfaces are protected.
You can also configure special ARP Telnet protection to protect specified Layer-3
interfaces. If the default route exists, you can enable special ARP Telnet protection on
the gateway of the network segment where the next hop of the default route resides
through enabling default-route Telnet protection. By default, default-route Telnet
protection is disabled.
Before configuring Telnet protection, you need to enable Telnet, SNMP, and ICMP
protection respectively. You can configure Telnet protection, SNMP protection, and
ICMP protection for only the packets of the specific source IP addresses.
Caution:
After the network address translation (NAT) function is enabled,
zYou cannot configure global Telnet protection.
zYou cannot configure special ARP Telnet protection for the Layer-3 interface where
NAT resides.
zYou cannot configure default-route Telnet protection.
Operation Manual – Telnet Protection
H3C S7500 Series Ethernet Switches Chapter 1 Telnet Protection Configuration
1-2
1.2 Telnet Protection Configuration
1.2.1 Configuring Telnet Protection
Follow these steps to configure Telnet protection:
To do... Use the command... Remarks
Enter system view system-view —
Enable Telnet
protection
attack-protection telnet
[ ip-address ]
Required
If you use this command with the
ip-address parameter, you can
protect the packets that match
this source IP address only.
Enable global
Telnet protection
or special ARP
Telnet protection
attack-protection
[ ip-address ]
Required
If you use this command with the
ip-address parameter, you can
protect the specified Layer-3
interfaces.
1.2.2 Configuring SNMP Protection
Follow these steps to configure SNMP protection:
To do... Use the command... Remarks
Enter system view system-view —
Enable SNMP
protection
attack-protection
snmp [ ip-address ]
Required
If you use this command with the
ip-address parameter, you can
protect the packets that match this
source IP address only.
Enable global Telnet
protection or special
ARP Telnet
protection
attack-protection
[ ip-address ]
Required
If you use this command with the
ip-address parameter, you can
protect the specified Layer-3
interfaces.
1.2.3 Configuring ICMP Protection
Follow these steps to configure ICMP protection:
Operation Manual – Telnet Protection
H3C S7500 Series Ethernet Switches Chapter 1 Telnet Protection Configuration
1-3
To do... Use the command... Remarks
Enter system view system-view —
Enable ICMP
protection
attack-protection
icmp [ ip-address ]
Required
If you use this command with the
ip-address parameter, you can
protect the packets that match
this source IP address only.
Enable global Telnet
protection or special
ARP Telnet
protection
attack-protection
[ ip-address ]
Required
If you use this command with the
ip-address parameter, you can
protect the specified Layer-3
interfaces.
1.2.4 Configuring Default-route Telnet Protection
Follow these steps to configure default-route Telnet protection:
To do... Use the command... Remarks
Enter system view system-view —
Enable default-route
Telnet protection
undo attack-protection
disable-defaultroute
Required
By default, default-route
Telnet protection is
disabled.
Andere Handbücher für S7500 Series
29
Andere H3C Schalten Handbücher
H3C
H3C S6300 Series Bedienungs- und Wartungshandbuch
H3C
H3C S3100 Series Bedienungsanleitung
H3C
H3C S9500 Series Bedienungsanleitung
H3C
H3C S12500 Series Service-Handbuch
H3C
H3C S6820-56HF Bedienungs- und Wartungshandbuch
H3C
H3C S5830V2 series Bedienungsanleitung
H3C
H3C S12500X-AF Series Anwendungshandbuch
H3C
H3C LS-3100-16TP-EI-H3-A-O Bedienungsanleitung
H3C
H3C S6890 Series Kurzanleitung
H3C
H3C S9500E Series Bedienungsanleitung
H3C
H3C S9500 Series Bedienungsanleitung
H3C
H3C S9500 Series Bedienungsanleitung
H3C
H3C S5560S-SI Bedienungsanleitung
H3C
H3C S7502 Bedienungsanleitung
H3C
H3C S5500-SI Series Bedienungsanleitung
H3C
H3C S7500 Series Bedienungsanleitung
H3C
H3C S6860-54HF Bedienungs- und Wartungshandbuch
H3C
H3C S3100 Series Montageanleitung
H3C
H3C FS5100-EI Series Bedienungsanleitung
H3C
H3C S7500E-XS Series Installationsanleitung
