H3C S9500E Series Kurzanleitung

Contents

Connecting the switch to the network························································································································· 1

Cable routing recommendations ·····································································································································1

Logging in to the switch····················································································································································1

Connecting the console cable·································································································································1

Setting up a configuration environment·················································································································2

Powering on the switch·····················································································································································5

Verification after power-on······································································································································7

Connecting the switch to the network ·····························································································································8

Connecting the switch to the network through an AUX cable·············································································8

Connecting the switch to the network through an Ethernet twisted pair cable··················································8

Connecting the switch to the network through an optical fiber···········································································9

Connecting the switch to the network

Cable routing recommendations

Interface cables and power cords should be separately routed. Reasonable cable routing can improve

efficiency by facilitating installation and removal of fan trays, and some other components.

•Interface cables are routed through the cable management brackets on the left and right sides of the

chassis and bound at cabling racks on chassis sides, depending on the available equipment room

condition.

•Put all the data signal cable adapters neatly under the chassis (instead of any places outside the

chassis in case of unexpected damages).

•The power cords run along the left-rear of the chassis and out of the chassis either from the chassis

top or the raised floor depending on the equipment room conditions (power distribution rack,

lightning protection box, and connector strip, etc.) of the exchange office.

•Long cables can be bound with cable ties. Do not bind cables at the air exhaust vent to prevent the

cables from aging too fast. For more information, see "Appendix E Cable management."

•Fix cables as near the switch as possible. The cables between the fixing point and switch interfaces

must be bound loosely.

•To identify cables, you can stick labels on them. For more information, see "Appendix F

Engineering labels for cables."

Logging in to the switch

Logging in through the console port is the most common way to log in to a switch. It is also the

prerequisite to configuring other login methods.

Connecting the console cable

A console cable is an 8-core shielded cable, with a crimped RJ-45 connector at one end for connecting

to the console port of the switch, and a DB-9 female connector at the other end for connecting to the

serial port on the console terminal.

Figure 1 Console cable

Table 1 Console cable pinouts

RJ-45 pin Signal DB-9 pin Signal

1 RTS 8 CTS

2 DTR 6 DSR

3 TXD 2 RXD

4 CD 5 SG

5 GND 5 SG

6 RXD 3 TXD

7 DSR 4 DTR

8 CTS 7 RTS

Figure 2 Connecting the switch and the PC through the console port

To connect the console cable:

1. Connect the DB-9 connector of the console cable to the serial port of a PC or terminal.

2. Connect the RJ-45 connector of the console cable to the console port of the MPU of the switch.

NOTE:

hen you remove the console cable, first unplu

the RJ-45 end, and then the DB-9 end.

Setting up a configuration environment

1. Select Start > All Programs > Accessories > Communications > HyperTerminal.

The Connection Description dialog box appears.

2. Enter the name of the new connection in the Name field and click OK.

Figure 3 Connection description

3. Select the serial port to be used from the Connect using list, and click OK.

Figure 4 Setting the serial port used by the HyperTerminal connection

4. Set Bits per second to 9600, Data bits to 8, Parity to None, Stop bits to 1, and Flow control to None,

and click OK.

Figure 5 Setting the serial port parameters

5. Select File > Properties in the HyperTerminal window.

Figure 6 HyperTerminal window

6. On the Settings tab, set the emulation to VT100 and click OK.

NOTE:

H3C recommends that you select the Windows keys option button.

Figure 7 Setting the terminal emulation in Test Properties dialog box

Powering on the switch

CAUTION:

Before powering on the switch, identify the power switch in the equipment room so that you can disconnec

the power supply promptly in case of an emergency.

Before powering on the switch, verify that:

•The interface cables, power cables and the grounding cable are correctly connected.

•The input power voltage meets the requirement of the switch.

•The console cable is properly connected, the terminal or PC used for configuration has started, and

the configuration parameters have been set.

Powering on the switch

1. Turn on the power switch of the power source providing power to the switch.

2. Turn on the power switch on the switch.

Before the switch is powered on, the following information is displayed:

DDR2 SDRAM test successful.

System is starting...

Booting Normal Extend BootWare

The Extend BootWare is self-decompressing..........................

Done!

****************************************************************************

* *

* H3C S9500E BootWare, Version 1.09 *

* *

****************************************************************************

Compiled Date : Jul 22 2009

CPU Type : MPC8548E

CPU L1 Cache : 32KB

CPU L2 Cache : 512KB

CPU Clock Speed : 1000MHz

Memory Type : DDR2 SDRAM

Memory Size : 1024MB

Memory Speed : 400MHz

BootWare Size : 4MB

Flash Size : 128MB

cfa0 Size : 247MB

NVRAM Size : 1024KB

BASIC CPLD Version : 001F

EXTEND CPLD Version : 001F

PCB Version : Ver.B

The switch initiates the power-on self-test (POST) and the results are displayed at the console terminal.

Board self testing...........................

Board steady testing... [ PASS ]

Board SlotNo... [ 0 ]

Subcard exist testing... [ PASS ]

DX246 testing... [ PASS ]

PHY88E1111 testing... [ PASS ]

CPLD1 testing... [ PASS ]

CPLD2 testing... [ PASS ]

NS16550 register testing... [ PASS ]

The default switch's Mac address... [00:e0:fc:00:95:12]

CF Card testing... [ PASS ]

BootWare Validating...

Press Ctrl+B to enter extended boot menu...

When the POST is complete, the switch boots the applications. The following information appears on the

terminal screen (only part of the display information is given in this example):

Starting to get the main application file--flash:/switch.bin!

The main application file is self-decompressing...........................

..........................................................................

Done!

System is starting...

Starting application at 0x00100000 ...

TLB init OK.

LBC init OK.

LAW init OK.

Bsp init start...

MMU init OK.

CRC init OK.

Frame data init OK.

Connect IRQ 0 OK.

Enable IRQ 0 OK.

Connect IRQ 1 OK.

Enable IRQ 1 OK.

Connect IRQ 2 OK.

Enable IRQ 2 OK.

Connect IRQ 4 OK.

Enable IRQ 4 OK.

Connect IRQ 5 OK.

Enable IRQ 5 OK.

Connect IRQ 6 OK.

After the switch completes booting the applications, the following information appears on the terminal

screen:

Press ENTER to get started.

Press Enter to begin configuring the switch at the prompt:

<H3C>

NOTE:

•The S9500E switches provide a command line interface (CLI). For more information about the CLI, see

H3C S9500E Switch Series Fundamentals Configuration Guide.

•The output depends on your switch model.

Verification after power-on

H3C recommends that you check the following conditions after the switch is powered on:

•The cooling system is working. You should be able to hear fan rotation noise and feel air being

blown out.

•All the LEDs are functioning properly.

Table 2 LED status when the switch operates properly

Part LED Name/Color Status

MPU MPU status LED

SFC (green) Steady on

ACT (green)

•Active MPU—Steady on

•Standby MPU—Off

RUN (green) Flashing

LPU status LED RUN (green) Flashing

Part LED Name/Color Status

Power supply Power supply

input/output LED

IN (green) Steady on

OUT (green) Steady on

Fan tray Fan tray status LED

RUN (green) Steady on

ALM (red) Off

For the LED description of LPUs, service cards, and subcards, see "Appendix B LEDs."

Connecting the switch to the network

TIP:

fter connectin

the switch to the network, you can use the ping or tracert command to check the

interoperability between the switch and network. For more information, see

H3C S9500E Switch Series

Network Management and Monitoring Command Reference

Connecting the switch to the network through an AUX cable

You need an AUX cable when configuring a switch with the remote modem dial-up approach.

An AUX cable is an 8-core shielded cable. At one end of the cable is an RJ-45 connector and at the other

end is a DB-9 (male) connector. Plug the RJ-45 connector into the AUX port of the switch and the DB-9

(male) connector into the DB-9 (female) port of the modem. An AUX cable is the same as a console cable.

For more information, see Figure 1 and Table 1.

To connect the AUX port:

1. Plug the RJ-45 connector of the AUX cable into the AUX port of the switch.

2. Plug the DB-9 (male) connector at the other end into the serial port of the modem.

Connecting the switch to the network through an Ethernet

twisted pair cable

The 10/100/1000Base-T copper ports of the switch support MDI/MDI-X auto-sensing. They are

connected to the network through category-5 or above twisted pairs that are equipped with RJ-45

connectors.

To con nect a 10/100 /1000 Base -T p or t:

1. Plug one end of an Ethernet twisted pair cable into the copper Ethernet port (RJ-45 port) to be

connected on the switch.

2. Plug the other end of the cable into the RJ-45 port of the peer device.

NOTE:

No Ethernet twisted pair cables are shipped with the switch. Prepare them yourself.

Connecting the switch to the network through an optical fiber

Use an optical fiber to connect an optical fiber port, for example, Ethernet fiber port, POS fiber port, or

RPR fiber port, on the switch to the network. You must install a transceiver module to the switch, and then

insert the fiber connector to the module.

Introduction to fiber connector

Fiber connectors are indispensable passive components in an optical fiber communication system. They

allow the removable connection between optical channels, which makes the optical system debugging

and maintenance more convenient and the transit dispatching of the system more flexible. Among

various fiber connectors, only the LC connector is described here.

Figure 8 LC connector

Precautions

Follow these precautionary steps:

•When selecting a fiber network facility, make sure the type of the connector and the fiber matches

the adopted optical port.

•Be sure to install the dust cover if the optical port is not connected to a fiber connector.

•Some invisible rays may be emitted from the optical port if the optical port is not connected to a

fiber connector or the dust cover is removed. Therefore, never stare at the optical port directly.

•Never bend or curve a fiber when connecting it.

Installing a transceiver module

The installation procedures of an XFP, SFP, and SFP+ module are similar. The following uses an SFP

module as an example.

CAUTION:

Do not touch the golden finger of an SFP module during installation.

To install an SFP module:

1. Put on an ESD-preventive wrist strap, and make sure it makes good skin contact, and is well

grounded.

2. Unpack the SFP module. Close the clasp by pushing it up over the SFP module, and then gently

insert the SFP module into the interface slot until it clicks into place, as shown in Figure 9.

Andere Handbücher für S9500E Series

Inhaltsverzeichnis

Andere H3C Schalten Handbücher

H3C

H3C H3C S3600 Series Bedienungsanleitung

H3C

H3C WX3000 Series Bedienungsanleitung

H3C

H3C S3100-8C-Sl Bedienungsanleitung

H3C

H3C S5130S-HI Series Bedienungsanleitung

H3C

H3C S7508E-X Bedienungs- und Wartungshandbuch

H3C

H3C S5500-SI Series Bedienungsanleitung

H3C

H3C S9500 Series Bedienungsanleitung

H3C

H3C S12500X-AF Series Kurzanleitung

H3C

H3C s5820x series Installationshandbuch

H3C

H3C S6805 Series Bedienungsanleitung

H3C

H3C S10500 Series Bedienungsanleitung

H3C

H3C S5500-HI Switch Series Bedienungsanleitung

H3C

H3C S12500-X Bedienungsanleitung

H3C

H3C S7500 Series Bedienungsanleitung

H3C

H3C S3610 Series Bedienungsanleitung

H3C

H3C S5500-EI series Bedienungsanleitung

H3C

H3C S6820 Series Installationshandbuch

H3C

H3C S5120-SI Series Bedienungsanleitung

H3C

H3C S5500-EI series Bedienungsanleitung

H3C

H3C S9500 Series Bedienungsanleitung

H3C

H3C S5130-EI Series Bedienungsanleitung

H3C

H3C S3610 Series Bedienungsanleitung

H3C

H3C S6850 Series Bedienungsanleitung

H3C

H3C S3100V2-52TP Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung