Haier GDZ10-0677 Bedienungsanleitung

Automatic Electric Dryer

User Manual and Instructions

Model˖GDZ10-0677

Ultra Plus Capacity

Start

Pause

Power

On/Off

Normal

Heavy Duty

Whites

Bulky

Press Free

Delicate

Touch Up

Bulky

Auto

Dry

Cycles

Timed Dry

Rack Dry

Timed

Dry

Cycles

Less

Time

Wrinkle

Saver

Sensor

Dry

Level

TempSignal

High

Medium

No Heat

Low

Louder

Softer

Off

Dry

Cool Down

Cycle Completed

Wrinkle Saver

RemainingTime

ExtendTumble

Very

Normal

Damp

English

IMPORTANT SAFETY

INSTRUCTIONS

WARNING - To reduce the risk of ﬁre, electric shock, or

injury to persons when using your appliance, follow the

basic precautions, including the following:

1. Read all of the instructions before using this appliance.

2. Don’t dry articles that have been previously cleaned in, washed in,

soaked in, or spotted with gasoline, dry clean solvents or other

ﬂammable explosive sub stains as they give off vapors which could

ignite or explode.

3. Do not allow children to play on or in the appliance. Close

supervision of children is necessary when the appliance is used

near children.

4. Before the appliance is removed from service or discarded, remove

the door to the drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to

water and/or to the weather.

7. Do not tamper with controls.

8. Do not repair or replace any part of the appliance or attempt any

servicing unless speciﬁcally recommended in the user-repair

instructions that you understand and have skills to carry out.

9. Do not use fabric softeners or products to eliminate static unless

recommended by the manufacturers of the fabric softener or product.

10. Do not use heat to dry articles or products to eliminate static unless

recommended by the manufacturers of the fabric softener or product.

11. Clean lint screen before or after each load.

12. Keep area around the exhaust opening and adjacent surrounding

areas free from the accumulation of lint, dust and dirt.

13. Keep the dryer area clear and free from items that would obstruct

the ﬂow of combustion and ventilation air through the louvered panel

located on the rear of the dryer.

14. The interior of the appliance and the exhaust duct should be cleaned

periodically by qualiﬁed service personnel.

English

Thank you for using our Haier

product. This easy-to-use manual

will guide you in getting the best

use of your dryer.

Remember to record the model and

serial number. They are on a label

in back of the dryer.

Model number

Serial number

Date of purchase

Staple your receipt to your manual.

You will need it to obtain warranty service.

15. Do not place items exposed to cooking oils in your dryer. Items

contaminated with cooking oil may contribute to a chemical reaction

than could cause a load to catch ﬁre.

16. If material has been used with any ﬂammable liquids or solids, it

should not used in the dryer until all terraces of ﬂammable liquids

and its fumes have been removed.

17. This dryer must be properly installed in accordance with the

installation instructions before it is used. See grounding instructions in

the installations sections.

18. Proper grounding must be ensured to reduce the risk of electric shock

and force. Check with a qualiﬁed electrician or service personnel if

you are in doubt as to whether the dryer is properly grounded.

19. Use the dryer only for its intended purpose: drying clothes.

20. Always disconnect dryer from electrical supply before attempting any

service. Disconnect power cord by grasping the plug, not the cord.

21. Replace worn power cord and/or loose plugs.

22. To reduce the risk of electric shock or ﬁre, do not use extension cords

or adapters to connect dryer electrical power source.

SAVE THESE

INSTRUCTIONS

DANGER

Risk of child entrapment. Before you throw away your old dryer,

take off the door so that children may not get trapped inside.

English

PAGE

IMPORTANT SAFETY INSTRUCTIONS....................................... 1-2

INSTALLATION INSTRUCTIONS.............................................. 4-11

Tools and Materials Required ............................................................ 4

Electrical Requirements ..................................................................... 5

Unpacking Your Dryer ..................................................................... 5

Exhaust System Requirements .............................................................6

Location of Your Dryer ......................................................................8

Manufactured (Mobile) Home Instruction ............................................9

Electrical Installation .......................................................................10

Power Cord Connections ............................................................... 11

Replacement Parts .......................................................................... 11

OPERATING INSTRUCTIONS ............................................... 12-21

Understanding the Control Panel...................................................... 12

Preparations before Drying ............................................................. 14

Load clothes into Dryer ................................................................... 15

Auto Dry ...................................................................................... 15

Timed Dry 18

Other Features .............................................................................. 19

Normal Operating Sounds.............................................................. 20

Tips .............................................................................................. 20

CARE AND CLEANING GUIDE.......................................................20

TROUBLESHOOTING.................................................................. 21

SPECIFICATIONSR ......................................................................21

TABLE OF CONTENTS

.....................................................................................

Rack Dry 18

.......................................................................................

WAR Risk of Fire:

1. Clothes dryer installation must be performed by a

qualiﬁed installer.

2. Install the clothes dryer according to the manufacturer’s

instructions and local codes.

3. To reduce the risk of severe injury or death, follow all installation

instructions.

SAVE THESE INSTRUCTIONS

Tools and materials required

• Phillips-Head and ﬂathead screwdrivers

• Channel-lock adjustable pilers

• 1/2-inch open-end wrench

• Carpenter’s level

• Measuring tape (12ft. min.)

• Duct tape

• Rigid or ﬂexible metal 4 inch (102cm) duct

• Vent hood

INSTALLATION INSTRUCTIONS

English

NING

4. Do not install a clothes dryer with ﬂexible plastic venting materials.

If ﬂexible metal (foil type) duct is installed, it must be of a speciﬁc

type identiﬁed by the appliance manufacturer as suitable for use

with clothes dryers. Flexible venting materials are known to collapse,

be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airﬂow and increase the risk of ﬁre.

Unpacking Your Dryer

English

1. Remove all packaging material. This includes the foam base and all adhesive

tape holding the dryer accessories inside and outside.

2. Inspect and remove any remains of packaging, tape or printed materials

before using the dryer.

Individual 30 Amp branch circuit fused with 30 Amp time-delay fuses or circuit

breakers. Use seperately fused circuits for washers and dryers, and DO NOT

operate a washer and dryer on the same circuit.

Power Supply

220 Volt, 1 Phase, 50Hz, AC

ELECTRICAL REQUIREMENTS

Circuit

The following are speciﬁc requirements for

proper and safe operation of your dryer. Failure

to follow these instructions can create excessive

drying times and ﬁre hazards.

1. Do not use plastic ﬂexible duct to exhaust the dryer. Excessive lint can build up

inside exhaust system and create a ﬁre hazard and restrict air ﬂow. Restricted

air ﬂow will increase drying time. If your present system is made up of plastic

duct or metal foil duct, replace it with a rigid or ﬂexible metal duct. Ensure

present duct is free of any lint prior to installing dryer duct.

2. The dryer must not be exhausted into any gas vent, chimney, wall, ceiling

The dryer exhaust system MUST be exhausted to the outdoors.

If the dryer is not exhausted outdoors, some

the laundry area. An accumulation of lint in any area of the home can

create a health and ﬁre hazard.

3. Exceeding the length of duct pipe or number of elbows allowed in the

“Maximum Length” chart can cause an accumulation of lint in the exhaust

system. Plugging the system could create a ﬁre hazard, as well as increase

drying times.

4. Do not screen the exhaust ends of the vent system. Lint can become caught in

the screen, increasing drying time. Use an approved vent hood to terminate the

duct outdoors, and seal all joints with duct tape.

5. All male duct pipe ﬁttings must be installed downstream with the ﬂow of air.

6. Exhaust duct must not be connected or secured with scews or other fastening

devices which extend into the interior of the duct.

7. Do not allow combustible material (clothing, draperies/curtains, paper, etc.) to

come in contact with exhaust system.

Explosion hazard:

Do not install the dryer where gasoline or other ﬂammables are kept or

stored. If the dryer is installed in a garage, it must be a minimum of 18

inches (45.7cm) above the ﬂoor. Failure to do so can result in death,

explosion, ﬁre or burns.

Exhaust Requirements:

Use only 4 inch (10.2cm) diameter (minimum) rigid or ﬂexible metal duct and

approved vent hood which has a swing-out damper hat open when the dryer is

in operation. When the dryer stops, the dampers automatically close to prevent

drafts and the entrance of insects and rodents. To avoid restricting the outlet,

WARNING

EXHAUST SYSTEM REQUIREMENTS

English

attic, crawl or any concealed space of a building.

ﬁne lint will be expelled into

1. Only rigid metal duct work should be used.

2. Venting vertically through a roof may expose the exhaust system to down

drafts causing an increase in vent restriction.

3. Running the exhaust system through an uninsulated area may cause

condensation and faster accumulation of lint.

4. Compression of crimping of the exhaust system will cause an increase in

vent restriction.

The exhaust system should be inspected and cleaned a minimum of every 12

months with normal usage. The more the dryer is used the more often you

should check the exhaust system and vent hood for proper operation.

English

RECOMMENDED MAXIMUM

Exhaust Hood Types

Recommended Use only for short

run installations

No. of 90º

elbows Rigid Metal Flexible Metal Rigid Metal Flexible

Metal

0 90 ft. Flexible metal 60 ft.

1 60 ft. 45 ft.

2 45 ft. 35 ft.

3 35 ft. 25 ft.

The exhaust duct shall be 4 inch (102 mm) in diameter.

maintain a minimum of 12 inches (30.5cm) clearance between the vent hood

and the ground or any other obstruction. The vent ﬂap should be able to move

freely, although vertical orientation of the exhaust system is acceptable. Certain

extenuating circumstances could affect the performance of the dryer:

metal shoud only

length to be 7.5ft.

wall.Maximum

the dryer and the

be used between

Flexible metal

metal shoud only

length to be 7.5ft.

wall.Maximum

the dryer and the

be used between

English

Do Not Install Your Dryer:

1. In an area exposed to dripping water or outside weather conditions.

2. In an area where it will come in contact with curtains, thick carpet, or anything

that will obstruct the ﬂow of combustion and ventilation air.

3. On carpet, ﬂoor must be solid with a maximum slope of 1inch (2.54 cm). Any

ﬂoor unevenness should be corrected with leveling legs located on the bottom

of the dryer.

Installation in Alcove or Closet:

1. DO NOT install your dryer in a closet with a solid door.

2. A dryer installed in a bedroom, bathroom, alcove or closet MUST be

exhausted outdoors.

3. No other fuel burning appliance shall be installed in the same closet .

4. Refer to the images on this page to ensure the installation provides the

minimum amount of clearance required for ventilation.

5. When installing the dryer in a closet with a door, a minimum of 120 square

inches (774.2 square cm) of ventilation in the door is required. Openings must

be equally divided at the top and bottom of the door and airﬂow must be

unobstructed. A louvered door with equivalent air openings for the length of

the door is acceptable.

LOCATION OF YOUR DRYER

0 in

(0 cm)

Door Open 90°

43 1/4”

˄109.7cm˅

˄34.3cm˅

13 1/2”

27”

(68.6cm) (122cm)

48”

30 3/8”

(77.7cm)

3 3/8”(8.4cm)

English

1. Dryer MUST be exhausted outside (outdoors, not beneath the manufactured

home) using metal ducting that will not support combustion. Metal ducting must

be 4 inch (10.16 cm) in diameter with no obstructions. Rigid metal duct

is preferred.

2. If dryer is exhausted through the ﬂoor and area beneath the manufactured

home is enclosed, the exhaust system MUST terminate outside the enclosure

with the termination securely fastened to the mobile home structure.

3. Refer to previous sections for other important venting requirements.

4. Installation must conform to current Manufactured Home Construction & Safety

Standard

MANUFACTURED (MOBILE) HOME INSTALLATION

Inhaltsverzeichnis

Andere Haier Trockner Handbücher

Haier

Haier HDY-D70-F Bedienungsanleitung

Haier

Haier CGDE450AW Bedienungsanleitung

Haier

Haier HDHP80A1 Bedienungsanleitung

Haier

Haier HDY-E60 Bedienungsanleitung

Haier

Haier RDE350AW - 6.5 Cu. Ft. Electric Dryer Bedienungsanleitung

Haier

Haier Ginesis HLF103Q Bedienungsanleitung

Haier

Haier LDS7HC Bedienungsanleitung

Haier

Haier HDY-D60 Bedienungsanleitung

Haier

Haier HD90-A636-F Bedienungsanleitung

Haier

Haier TCD60E Bedienungsanleitung

Haier

Haier RDE350AW - 6.5 Cu. Ft. Electric Dryer Bedienungsanleitung

Haier

Haier HDM8.0-61 Bedienungsanleitung

Haier

Haier HD80-A2939 Bedienungsanleitung

Haier

Haier HLF11E Bedienungsanleitung

Haier

Haier HD70-01 ME Bedienungsanleitung

Haier

Haier HLP141E Bedienungsanleitung

Haier

Haier GDZ5-1C Bedienungsanleitung

Haier

Haier T60-32 Bedienungsanleitung

Haier

Haier HDY-D60 Bedienungsanleitung

Haier

Haier GDG480BW Bedienungsanleitung

Haier

Haier HD80-01-U Bedienungsanleitung

Haier

Haier GDZ5-1 Bedienungsanleitung

Haier

Haier Ginesis HLF103Q Bedienungsanleitung

Haier

Haier Genesis CRDWE200AW Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Miele

Miele TWH 780 WP Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Bedienungsanleitung

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung