Haier HLP455E Bedienungsanleitung

Model : HLP455E

Please read this manual

carefully before using.

Retain it for future reference.

The machine is for cold water

connection only.

Twin-tub Washing Machine

User's manual

ContentsContents

the back cover

Safety precautions

Installation and adjustment

Preparation before washing

The musts in washing

Usage of the detergent

Washing sequence

Disposal after washing

Packing list & Specification

Names of the parts

Trouble-Shooting Answer to question

Names of the parts

Wash tub

Wash tub cover

Outer cover of the spin tub

Inner cover of

the spin tub

Spin timer

Wash timer

Wash selector

Water-filling entrance

Control panel

Spin tub

Cabinet

Power cord

Hook of fixing

the drain hose

Back cover

Drain hose

Cabinet handle

Filter cover

Bottom foot

Pulsator Base frame

Meaning and description of the symbols

Warning sign

Forbidding sign

Contents marked with that symbol are related

to the safety of the product and the personal

safety of the users. Please operate in strict

conformity to the contents, otherwise it may

cause damage of the machine or injure the

personal safety of the user.

Contents marked with that symbol are actions

forbidden to perform. Performing of those

actions may result in damage of the machine

or injure the personal safety of he user.

Please check if the power receptacle has good earthing condition before

using to guarantee your safety.

Safety precautions

Please insert the power cord into special

receptacle with rated voltage. Be sure to

use single-phasethree pins receptacle.

The ground terminal of the receptacle

must be properly grounded. If possible,

please adopt electric leakage protector.

When the machine is normally using,

please put the power plug at the location

easily to be inserted and extracted by hand.

Be sure to pull the plug off when there's

power failure, or the machine is being

moved, cleaned or when it is idle.

If the power cord is bad, to avoid risk it is required to replace it by the

technicians of our special shop or the customer care department.

Keep the pin of the power plug clean.

Do not put the machine at damp

place like the bathroom . Never

wash it with water. Do not place

wet laundries on the control panel.

Do not use water hotter than 50 C .

In case the washing machine is installed

on ground with carpet , do not block the

ventilation hole with carpet.

Ventilation hole at

the bottom of the

washing machine

Do not wash water-proof laundries like

the raincoat, bike covers etc. to avoid

abnormal vibrations in spinning.

Do not let the machine share one receptacle

with other electric appliances. If the power

plug is damaged, or the plugging into the

receptacle is loose, do not use the plug any

more.

Earth

Do not stretch hands into the working

machine. It is dangerous even if the

rotation is slow. Take special care of

the children.

Safety precautions

Do not put any hot or heavy items

( such as the kettle with hot water )

on the washing machine.

Do not decompose, repair or alter the

machine by yourself.

Handicapped or children without care

shall not use the machine.

Do not wash laundries with volatile

materials (such as thinner, petrol etc.).

Petrol

Thinner

Keep the machine away from direct

sunlight and heat source like the

heater.

To protect your laundries and wash-

ing machine, please take out all of the

coins, buttons, sand, hairpin and

other foreign materials before washing.

Please check if the water faucet is open,

and if the connection of the water inlet

pipe is proper.

It is suggested to use foamless washing

powder.

Installation and adjustment

Please install and adjust the machine according to the requirement of the manual. It is

very important to your security and correct operating the machine.

Usage of the drain hose

1.The height of the drain hose shall be

less than 10cm, or the drainage will not

be smooth, and cost such long time that

the machine may stop at mid way.

2.Do not ramp or press the drain hose.

The drain hoseshall drain smoothly

4.If extra drain hose is needed, please

make separate purchase. The inner

diameter of the extra hose shall not

less than 26mm, and the length shall

not exceed 1.5m.

Install the water inlet hose

Please install thewater inlet accordingto the machine.

Control panel s frame (Figure 1)

Insert the Water inlet pipe into the Water-filling

entrance If want todemount the water inlet pipe

pull it out .

Figure 1

Water inlet pipe

Water-filling entrance

3.If the drain hose is too long, cut it at mid

point. To make smooth drainage, cut the

front end of the hose slantingly.

If the extrahose is toolong, cut it

either atA orat B point.

Preparation before washing

1.Connect the water inlet hose.

2.Confirm that the washing machine is properly

grounded . Then insert the power plug into the

receptacle. Do not connect the ground terminal

to the gas pipe and tap water pipe.

3.Put down the drain hose .

4.Slanting or uneven floor may result in

unstable working or abnormal noise. Please

make the machine stand horizontally.

Pay attention to followings before washing the laundries

Check if

the laundries

has special

requirement

on washing

Clear the

pocket. Take

out the coins,

sand, hairpins

etc.

Tie the long

strips; fasten

the buttons;

close zippers.

When the pulsator

is running , the

buttons of the

laundries may

cause noise. For

the sake of

discretion, please

put the laundries

with buttons into

other laundries.

The quantity of

the laundries

shall not be too

large. Stretch

and loosen the

laundries before

putting them in

the tub.

a. Check if the laundries are applicable for washing with machine.

b. Divide the laundries that are not colorfast from other laundries.

c. Put those laundries difficult to absorb water into water with hand.

d. For those laundries with heavy soil, please first remove the dirt like

mud or dust. For the parts with heavy soil, please apply detergent on

them in advance, which can make it easier to remove the soil.

e. For those laundries that may get lint ball and those with long fur, turn

it over before putting in.

f. Do not put those laundries polluted by chemicals into the washing

machine directly.

Operating instructions

The capacity of washing and spinning of the machine refer

to the largest weight of the standard laundries under dry

condition that can be washed or spinned in one time.

The thickness, size, type of the cloth will influence the actual

washing capacity. It is suitable to put in reasonable amount of

laundries and the laundries can be turned round in washing

for one time washing.

Do not select high water level for laundries less than 1.0kg,

so as to avoid splashing of water.

Usage of the detergent

How to use the whitener

Fill water to decided level. Dilute

the whitener with container. Pour

it slowly into the washing tub.

Avoid using whitener on laun-

dries with color or pattern as they

are prone to lose color.

The whitener shall not touch

the laundries directly.

Refer to the user's manual for

the usage and quantity of the

whitener.

For powder whitener, please

dissolve it before using.

Direct dissolved in the machine:

1.Fill small quantity of water.

2.Add the powder . Run for 30

seconds to dissolve it completely.

3.Put it in the laundries. Select suitable

water level.

The instant dissolving of the washing

powder:

1.Prepare warm water of 30 C and a

container.

2.Add the powder while stirring to fully

dissolve it.

The powder is more prone to pollute the

laundries than the detergent. Therefore

please use it with proper quantity.

Dosage of different washing powder is

different. Please refer to the instruction

of the washing powder for the detail

dosage.

How to use the washing powder

Washing sequence

DRAIN

WASH

Spin timer

SPIN TIMER

Wash timer

WASH TIMER

(To set to below 2 minute,

first set to 6 minute then

turn it back. it can increase

the service life of the timer).

(To set to below 1 minute,

first set to 2 minute then

turn it back. it can increase

the service life of the timer).

WASH SELECTOR

Water inlet

WATER INLET

SPIN TIMER

OFF

Wash timer

WASH TIMER

OFF

CYCLE SELECTOR

Figure 1

Washing sequence

Wash

2. Fill the water and add the dissolved washing

powder to make the water level reach the preset

position. Run washing program for some time to stir and

dissolve the powder completely.(Figure 1)

3.Put in the laundries. If the water quantity is

insufficient, please add water.

5.After washing, set the "WASH SELECTOR"

at "SPIN". (Figure 4).

1.Fill the water

Set the water-filling selector at the "WASH" side.

Set the water level adjusting lever to needed line.

Please note that the input water voltage should be

controled between 0.02~0.2MPa.

4.Select the current.

Select the strength of the current according to

the laundries. Select the washing time according to the

laundries. (Figure 2)(Figure 3)

1.Put the laundries into the spin tub

evenly and smoothly.

Midway spinning

2.Spin

(1) Put the gland in properly.

Please put in the gland properly even

if the laundries quantity is small.

(2) Close the inner and outer cover of the

spin tub.

(3) Spin for 1-2 minutes.

Push Gland

Proper The laundries

are slanting No gland

Outer cover of

The spin tub

Inner cover of

The spin tub

Proper

Push

Rinsing

1.Put the laundries into the wash tub. Select

suitable current according to the laundries.

2.Fill the water

Fill suitable water continuously according to

the laundries quantity.

3. Rinse

Adjust the wash timer to 5-7 minutes to do

rinsing.

Spinning

1.Put the laundries into the spin tub evenly and smoothly.

2.Press the gland in the tub properly. Close the inner and

outer cover of the spin tub.

3.Spin

Select suitable spin time according to the laundries and

do spinning. During spinning, if there is abnormal sound

it is generally owning to slanting placement of the laundries.

Please stop the machine and reorder the laundries.

4.In spinning it will pause the work if you open the outer

cover of the spin tub. Close it to resume the spinning.

3.If the water quantity filled is too large, the water

may flow out from the wash tub side. Please

twist the water tap to limit the water filling.

Figure 4

CYCLE SELECTOR

Figure 2

CYCLE SELECTOR

DRAIN

WASH

CYCLE SELECTOR

Figure 3

WASH TIMER

Wash timer

WASH TIMER

OFF

DRAIN

WASH

CYCLE SELECTOR

The input water level should

not exceed the labled position.

Please first pull off the power plug from the receptacle before cleaning.

Maintenance and cleaning

Wipe the complete unit with soft

cloth twisted dry.

Wipe with neutral detergent if

too dirty.

Do not wash it directly by water.

After washing, dismount the water inlet hose.

Do not store water in the tub for long perio d.

Discharge the water immediately after each using.

Pull off the power plug and hang up the power

cord, Hang up the drain hose.

Wipe off the water drops on the surface and inside

the tub with clean soft cloth. Open the cover of the

wash tub and the inner/outer cover of the spin tub

for some time (about one hour), then close them.

Thinner

Alcohol

Petrol

Trouble-shooting

2~3L

Below 50

When the remained water is frozen

Prevent the freezing (be sure to discharge the water

completely after using)

After complete draining, set the "WASH SELECTOR"

at "STRONG" or "STANDARD". If it is set at "DRAIN",

it will be rather difficult for the frozen water to melt.

When the water is frozen

Pour hot water below 50 into the wash tub

to soak it completely. Then turn the pulsator

with hands gently. Please confirm the drainage

can work normally before next using.

Inhaltsverzeichnis

Andere Haier Waschmaschine Handbücher

Haier

Haier XQS50-28 Bedienungsanleitung

Haier

Haier XQB100-96 Bedienungsanleitung

Haier

Haier WD-8888-19 Bedienungsanleitung

Haier

Haier JW-K42F Bedienungsanleitung

Haier

Haier SBM600T Bedienungsanleitung

Haier

Haier HWM60-20B Bedienungsanleitung

Haier

Haier HBF601 Benutzerhandbuch

Haier

Haier HWM55-33W Bedienungsanleitung

Haier

Haier XPB50-LS Bedienungsanleitung

Haier

Haier HVS1200 Bedienungsanleitung

Haier

Haier HWF95AN1 Bedienungsanleitung

Haier

Haier HW150-BP14986ES9 Bedienungsanleitung

Haier

Haier HWT12AD1 Bedienungsanleitung

Haier

Haier HWM68-0523K Bedienungsanleitung

Haier

Haier XPB10-LAP Bedienungsanleitung

Haier

Haier XPB90-99VGS Bedienungsanleitung

Haier

Haier HWF5300AW Bedienungsanleitung

Haier

Haier HLP23E - Electronic Touch Pulsator Ing Portable Washing... Montageanleitung

Haier

Haier XPB90-99VGS Bedienungsanleitung

Haier

Haier HWM20-0701 Bedienungsanleitung

Haier

Haier TEL6TL Bedienungsanleitung

Haier

Haier GWT 450 AW Bedienungsanleitung

Haier

Haier HWM40-32 Bedienungsanleitung

Haier

Haier XQBM20-E Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

GE WSLP1500 Handbuch

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

Bosch

Bosch WAN2829BSN Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung